Esta versión puede contener ediciones incorrectas. Cambie a la última instantánea verificada.
Qué necesitas
-
-
Retire los cuatro tornillos que se muestran con un destornillador Phillips #00.
-
-
-
-
La botonera, en la base de la pantalla LCD, está sujeta por dos clips.
-
Haz palanca sobre los clips con una herramienta de apertura PSP. Esto liberará los clips.
-
-
-
El cable de cinta fino se abre desde el lado opuesto por el que entra el cable de cinta. Abre el pestillo hacia el cable de cinta. El pestillo tirará hacia arriba y liberará el cable de cinta. Coloca la herramienta detrás de la parte negra y levanta la pieza de plástico negra.
-
El cable de cinta ancho se abre desde el mismo lado en el que se engancha el cable de cinta, y se abre alejándose del cable.
-
Ambos cierres son las piezas negras.
-
Tira suavemente de los cables planos para separarlos de los pestillos. Ahora puedes retirar la pantalla LCD.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Now that the LCD is removed, unscrew the two screws in red.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
First Start by turning the PSP over, UMD Drive up.
-
Then using a small flat-head, Pry the lower left corner up.
-
The right side will come out after the left latch is free. Some jiggle work might be needed, no excessive force.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
FIRST, with the psp facing up, unscrew the black screw on the bottom right hand of the umd door adjacent to the right side speaker for easier prying of the umd door in the next step.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Hold the tray on the left side and slide it to the right.
-
Remove the tray.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Because the problem was that the door was loose, clean all parts of dirt or debris.
-
Align the tray to the 2 hinges at the bottom and slide the tray to the left, back into place. The latch should still be above the UMD frame.
-
Apply light pressure to the left side while lowering the tray to its original position.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
This next part is a bit tricky. Notice the slot for the spring arm and the slot for the UMD tray in the the corners.
-
Turn the PSP upside-down, so that the bottom is now facing up.
-
First slide the UMD tray into the slots on the UMD cover. Once these are in, align the spring into its slot.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Carefully close the PSP door, keeping the UMD tray and spring in their slots.
-
Insert the left side of the door first, then the right hinge.
-
This can be done using either your hands or a flat-head.
-
Cancelar: No complete esta guía.
36 personas más completaron esta guía.
4 comentarios
Hi, my UMD door opens too easily, just as i touch it sometimes, and i have to press it hard to close it. What should i do to make it stay close? i don’t understand why it has become so loose
You can actually use a file and an exacto knife and some sandpaper on an aftermarket door. They tried to make an L-shaped reinforcement on the right side (if looking at the PSP from the back) that's why it's quite hard to get it in past those screws, just shave and file and sliver little by little, until it fits in without even having to take off the front case. You may also have to do some trimming and gluing of the latch catch on most of these aftermarket UMD doors.