Introducción
Esta guía te ayudará a sustituir la pantalla LCD si se ha roto o dañado.
Qué necesitas
-
-
Ubique el botón de la carcasa de la batería en el lado posterior izquierdo de la PSP.
-
Presione el botón y retire la tapa de la batería.
You are dumbbb... BRO YOUR DUMB BC U DIDNT HAVE TO USE A TOOL TO OPEN THE DOOR. USE YOUR FINGER""
The battery door can be damaged dont use a tool
That also happend to me it got destroyed by screwdriver
-
-
-
Usando su dedo, retire la batería hacia arriba del sistema como se muestra.
The use of the opening tool is completely unnecessary. There is a finger actuated opening latch button that says “PUSH” on it. Simply press down with your thumb then slide your thumb down and away, dragining the battery door with it. It will then come off. Assuming the system still has its original plastics, they may have become brittle enough that the opening tool could damage the release button or the plastic cover.
-
-
-
Retire los cuatro tornillos que se muestran con un destornillador Phillips #00.
you need to peel back the warranty sticker in order to access both the lower left and lower left screws
This is a bit misleading, you should only remove the two black screws in the battery compartment. The silver ones can stay.
iFixit screwdriver bits aren't thin enough to reach the two screws on the right near the memory stick slot.
Can't edit previous comment so here's a new one:
Standard or older iFixit screwdriver bits aren't thin enough to reach the two screws on the right near the memory stick slot. You'll need precision bits that have longer tips to reach these deep screws.
-
-
-
-
La botonera, en la base de la pantalla LCD, está sujeta por dos clips.
-
Haz palanca sobre los clips con una herramienta de apertura PSP. Esto liberará los clips.
-
-
-
El cable de cinta fino se abre desde el lado opuesto por el que entra el cable de cinta. Abre el pestillo hacia el cable de cinta. El pestillo tirará hacia arriba y liberará el cable de cinta. Coloca la herramienta detrás de la parte negra y levanta la pieza de plástico negra.
-
El cable de cinta ancho se abre desde el mismo lado en el que se engancha el cable de cinta, y se abre alejándose del cable.
-
Ambos cierres son las piezas negras.
-
Tira suavemente de los cables planos para separarlos de los pestillos. Ahora puedes retirar la pantalla LCD.
-
Cancelar: No complete esta guía.
70 personas más completaron esta guía.
Un agradecimiento especial a estos traductores:
100%
¡ Carlos López (España - Spain) nos está ayudando a reparar el mundo! ¿Quieres contribuir?
Empezar a traducir ›
8 comentarios
This is not easy...I tore up the outer casing trying to do this. I better see money in the mail for this
People!! If you weren't gifted in screws and bolts, then bring your console to a repair shop. Seriously blaming this for your Dick Fingers?
dick fingers!!
It needs to be mentioned that the power switch is very fragile. When reassembling the front cover you need to first make sure that the small black switch on the circuit board sits in the yellow part of the switch, otherwise when you apply pressure to click the cover back in place the black switch will break off.
Great tutorial, thanks to this I manage to fix the R button, it turns out the ribbon cable of the right section of buttons was dirty and a little bit off of place, and taking out the screen was necessary to get to that connector.
Totally helpful thank u so much, a little bit of patience and common sense job was done an I was play my psp portable the instant I put the battery cover back on it! U guys ROCK TNX AGIAN!!