Saltar al contenido principal

Olympus FE-210 Lens Assembly Replacement

Qué necesitas

  1. Olympus FE-210 Lens Assembly Replacement, Battery: paso 1, imagen 1 de 2 Olympus FE-210 Lens Assembly Replacement, Battery: paso 1, imagen 2 de 2
    • The battery compartment is located on the bottom side of the camera. Push the button in, and slide the cover to get access to the batteries.

  2. Olympus FE-210 Lens Assembly Replacement: paso 2, imagen 1 de 2 Olympus FE-210 Lens Assembly Replacement: paso 2, imagen 2 de 2
    • The batteries will slide right out.

    • When putting new batteries in, make sure they are pointing the right direction.

  3. Olympus FE-210 Lens Assembly Replacement, Front Casing: paso 3, imagen 1 de 3 Olympus FE-210 Lens Assembly Replacement, Front Casing: paso 3, imagen 2 de 3 Olympus FE-210 Lens Assembly Replacement, Front Casing: paso 3, imagen 3 de 3
    • Remove the 7 screws holding the front case in place, with a #00 screwdriver.

    • Six screws are 3.6 mm.

    • The seventh screw is 3.2 mm.

  4. Olympus FE-210 Lens Assembly Replacement: paso 4, imagen 1 de 3 Olympus FE-210 Lens Assembly Replacement: paso 4, imagen 2 de 3 Olympus FE-210 Lens Assembly Replacement: paso 4, imagen 3 de 3
    • Pulling the front case off, requires applying enough strength in the right areas.

    • The front case snaps into place in three places:

    • At the top and bottom of the battery side (opposite of side pictured) of the case.

    • Right in the middle of the DC-in side (side pictured) of the case.

    • Top of the camera, to the left of the power button.

    • Once those places are disconnected, the front case will pop right off.

    • The camera in the first two pictures is upside down. This is the best position to place your thumbs to remove the case.

  5. Olympus FE-210 Lens Assembly Replacement, Rear Casing: paso 5, imagen 1 de 1
    • Remove the 3.2 mm screw in the battery compartment using a #00 screwdriver.

    • After removal of the screw the case will be loose, but do not tug it off. There is a cord connecting the rear controls to the motherboard.

  6. Olympus FE-210 Lens Assembly Replacement: paso 6, imagen 1 de 3 Olympus FE-210 Lens Assembly Replacement: paso 6, imagen 2 de 3 Olympus FE-210 Lens Assembly Replacement: paso 6, imagen 3 de 3
    • Carefully pull the rear case away from the camera until you have access to the cord connected to the motherboard.

    • Lift the white latch using a fingernail or a spudger.

    • Pull the cord from its connector.

  7. Olympus FE-210 Lens Assembly Replacement, Motherboard: paso 7, imagen 1 de 2 Olympus FE-210 Lens Assembly Replacement, Motherboard: paso 7, imagen 2 de 2
    • Remove the 2 pieces of translucent yellow tape.

    • Removing these pieces of tape will void the camera warranty. They serve no functional purpose and do not need to be replaced during reassembly.

  8. Olympus FE-210 Lens Assembly Replacement: paso 8, imagen 1 de 2 Olympus FE-210 Lens Assembly Replacement: paso 8, imagen 2 de 2
    • Remove the seven 2.7 mm using a #00 screwdriver.

  9. Olympus FE-210 Lens Assembly Replacement: paso 9, imagen 1 de 1
    • Remove the ribbon cord located near the top right corner of the motherboard. Do this by carefully pulling the cord out of the socket using a pair of tweezers.

  10. Olympus FE-210 Lens Assembly Replacement: paso 10, imagen 1 de 1
    • Disconnect the ribbon cord located on the left side of the motherboard.

    • Use tweezers or a spudger to lift the latch on the connector.

    • Carefully remove the cord from the connector.

  11. Olympus FE-210 Lens Assembly Replacement: paso 11, imagen 1 de 2 Olympus FE-210 Lens Assembly Replacement: paso 11, imagen 2 de 2
    • De-solder the 2 connection points.

    • Be careful to not damage any part of the circuit board with the soldering iron.

  12. Olympus FE-210 Lens Assembly Replacement: paso 12, imagen 1 de 1
    • Remove the motherboard from the camera casing.

  13. Olympus FE-210 Lens Assembly Replacement, Lens Assembly: paso 13, imagen 1 de 1
    • Remove the three 3.6 mm screws using a #00 screwdriver.

  14. Olympus FE-210 Lens Assembly Replacement: paso 14, imagen 1 de 2 Olympus FE-210 Lens Assembly Replacement: paso 14, imagen 2 de 2
    • Slide the lens to the left and pull up. The lens should easily come loose and slide right out.

Conclusión

To reassemble your device, follow these instructions in reverse order.

Matt

Miembro Desde 01/25/11

811 Reputación

6 Guías creadas

Equipo

Cal Poly, Team 4-36, Regan Winter 2011 Miembro de Cal Poly, Team 4-36, Regan Winter 2011

CPSU-REGAN-W11S4G36

3 Miembros

14 Guías creadas

Un comentario

This is also applicable to the Olympus FE170. I dismantled and repaired mine using this guide. Excellent!

Alan Shaw - Contestar

Agregar Comentario

Ver Estadísticas:

Ultimas 24 horas: 0

Ultimos 7 días: 2

Ultimos 30 días: 10

Todo El Tiempo: 6,173