Saltar al contenido principal
  1. Remove the 2 exposed screws on opposite sides of the camera. Turn the screws counter-clockwise to remove. Remove the 2 exposed screws on opposite sides of the camera. Turn the screws counter-clockwise to remove.
    • Remove the 2 exposed screws on opposite sides of the camera. Turn the screws counter-clockwise to remove.

  2. Open the battery compartment and remove the 2 screws in the top of the opening. Open the battery compartment and remove the 2 screws in the top of the opening.
    • Open the battery compartment and remove the 2 screws in the top of the opening.

  3. Remove the 2 exposed screws on the bottom of the camera. Remove the 2 exposed screws on the bottom of the camera.
    • Remove the 2 exposed screws on the bottom of the camera.

  4. Uncover the mini-usb dock on the side of the camera and unscrew the screw next to the flap joint
    • Uncover the mini-usb dock on the side of the camera and unscrew the screw next to the flap joint

  5. Uncover the video cable port on the side of the camera and remove the screw
    • Uncover the video cable port on the side of the camera and remove the screw

  6. Carefully slip the head of the plastic opening tool under the panels by finding the crack between the panels. Lightly apply pressure in the shown places at the top and bottom of the camera. Carefully slip the head of the plastic opening tool under the panels by finding the crack between the panels. Lightly apply pressure in the shown places at the top and bottom of the camera.
    • Carefully slip the head of the plastic opening tool under the panels by finding the crack between the panels. Lightly apply pressure in the shown places at the top and bottom of the camera.

  7. Loosen the panels on the sides of the camera in the shown places by slipping the plastic opening tool in the crack between the panels. Lightly apply pressure. Loosen the panels on the sides of the camera in the shown places by slipping the plastic opening tool in the crack between the panels. Lightly apply pressure.
    • Loosen the panels on the sides of the camera in the shown places by slipping the plastic opening tool in the crack between the panels. Lightly apply pressure.

  8. Ensure that the panels have been loosened. Carefully use hands to pull back and remove the panels. Ensure that the panels have been loosened. Carefully use hands to pull back and remove the panels.
    • Ensure that the panels have been loosened. Carefully use hands to pull back and remove the panels.

  9. Remove the three screws holding the outer circuit board in place. Remove the three screws holding the outer circuit board in place. Remove the three screws holding the outer circuit board in place.
    • Remove the three screws holding the outer circuit board in place.

  10. Use the spudger or your fingers to remove the outer circuit board from the camera. Use the spudger or your fingers to remove the outer circuit board from the camera.
    • Use the spudger or your fingers to remove the outer circuit board from the camera.

  11. Use the spudger to pull the plastic tabs shown off of the motherboard. Gently pull the plastic piece off of the motherboard. Gently pull the plastic piece off of the motherboard.
    • Use the spudger to pull the plastic tabs shown off of the motherboard.

    • Gently pull the plastic piece off of the motherboard.

  12. Remove the screws shown using the 00 philips screwdriver. Remove the screws shown using the 00 philips screwdriver. Remove the screws shown using the 00 philips screwdriver.
    • Remove the screws shown using the 00 philips screwdriver.

  13. Use the pointed end of the spudger to release the ribbon cable clasp. Remove the ribbon cable from the port using the tweezers. Remove the ribbon cable from the port using the tweezers.
    • Use the pointed end of the spudger to release the ribbon cable clasp.

    • Remove the ribbon cable from the port using the tweezers.

  14. Use the tweezers to remove the ribbon cable near the shutter button.
    • Use the tweezers to remove the ribbon cable near the shutter button.

  15. Next unsolder the connections shown.
    • Next unsolder the connections shown.

    • See our soldering guide for help on how to unsolder

    • Soldering irons are hot, and will also heat the connection wire. Using the tweezers will protect your fingers from the heat.

  16. Gently pull the motherboard (from the bottom first) away from the device. Gently pull the motherboard (from the bottom first) away from the device. Gently pull the motherboard (from the bottom first) away from the device.
    • Gently pull the motherboard (from the bottom first) away from the device.

Conclusión

To reassemble your device, follow these instructions in reverse order.

Tyler Hartwig

Miembro Desde 24/03/15

337 Reputación

3 Guías creadas

Equipo

Baylor, Team 6-4, Shaver Spring 2015 Miembro de Baylor, Team 6-4, Shaver Spring 2015

BU-SHAVER-S15S6G4

3 Miembros

6 Guías creadas

Agregar Comentario

Ver Estadísticas:

Ultimas 24 Horas: 0

Últimos 7 Días: 0

Últimos 30 Días: 0

Todo El Tiempo: 183