Saltar al contenido principal

Desmontaje de Oculus Quest 2

Qué necesitas

  1. Desmontaje de Oculus Quest 2, Desatornilla la tapa trasera: paso 1, imagen 1 de 1
    • Comienza quitando los seis tornillos T2 que sujetan el revestimiento interior de los auriculares al frente.

    It’s actually 6x T3 screws. A T2 driver is smaller than the groves of the T3 screws, will slip and strip.

    Steven - Contestar

    It may depend on your bit manufacturer. I used an ifixit T2.

    Daniel Yoder - Contestar

    What screw size are these? I need to replace one but I don't know what to search for

    Michele Bright -

    I have T2 on mine as well

    weiwei.e.sun - Contestar

    What if one of the screws strips? We are using a t3 and it got all screws out but one. Now we cannot get that last screw out

    AliD - Contestar

    Not much you can do except drill it out.

    Kmic -

  2. Desmontaje de Oculus Quest 2, Retira la tapa trasera: paso 2, imagen 1 de 2 Desmontaje de Oculus Quest 2, Retira la tapa trasera: paso 2, imagen 2 de 2
    • Un lado a la vez, inserta una púa al lado de la boquilla, deslízala hacia el borde y haz palanca.

    • Cuando ambos lados estén sueltos, levante con cuidado la cubierta y dóblala de modo que la boquilla quede en el perímetro exterior del dispositivo, como se muestra en la segunda imagen.

    • El sensor de proximidad todavía está conectado a través de un cable flexible, así que ten cuidado de no rasgar o arrugar el cable.

    • Levanta el pequeño clip negro del conector ZIF y extrae el cable flexible.

    • El cable está ligeramente adherido al auricular, así que ten cuidado al retirarlo.

    • Durante el montaje, asegúrate de colocar el cable correctamente. Volver a enganchar el pequeño clip negro no debería requerir mucha fuerza. Si no conectas el cable correctamente, la pantalla de los auriculares puede permanecer en negro y el dispositivo se apagará después de unos segundos.

    I’m going to do this in about 2 month and this part seems difficult any tips?

    Someone - Contestar

    Shove your prying tool right in the sides (right and left, where the two arrows pointing inward are) and it pops right out (don't push too fast, just keep pushing until it pops out, i suggest using the flat end of a normal Ifixit spudger)

    Kmic -

    I REALLY wish this step had some better close ups. I thought I connected the cable correctly but I'm getting the black screen silly stuff going on. Boo!

    Infinimitsu - Contestar

    You have to push the connector in a bit, and then the black clip will latch down. I'm using a lighted magnifier, myself.

    Shayne Cameron - Contestar

    Bouta throw this thing across the room trying to open it

    Possum - Contestar

  3. Desmontaje de Oculus Quest 2, Desatornille la tapa frontal: paso 3, imagen 1 de 1
    • Remueve los 3 tornillos P0

    • Remueve los dos tornillos P0

    • Los dos tornillos naranjas cerca de la parte superior son muy profundos, es posible que se requiera un destornillador de cabeza más larga

    Does iFixit have a set with a screwdriver for accessing the left top screw shown here? The space there is very narrow.

    S-ed - Contestar

    The correct size for these five screws is P000, not P0.

    Matthew Foreman - Contestar

    where can I look up the naming scheme for that screw size you’r etalking about?

    is that the same as the phillips PH000?

    is that describing the thread dimensions or the head of the screw, or both?

    I’ve looked up the screw dimensions / where I can get spares but can’t seem to find consistent results for this one,

    I want to know the screw’s head and thread measurements so I can recreate a custom oculus shell in CAD and have the proper screws and parts all fit back together properly.

    _latch_key_ -

    The ph screw driver was wrong and I stripped one of the screws thanks a lot ifixit

    gavilanesadan@yahoo.com - Contestar

    Of note; the screws are PH000 and they are especially soft and easy to strip.

    Alexander Owen - Contestar

    For those like me that do not have the Marlin screwdrivers or any other thin extension to reach the two deep screws, but if you do have an iFixit kit with bits: I used the normal PH00 bit and the 4mm nut driver as a DIY extension. However, they do not magnetize so this may require some extra finesse to ensure they don't fall apart.

    MINK - Contestar

    The ifixit kit comes with several ph sizes. There is ph000 ph00 and ph0 among others. It is printed on the side of the bits. They are definitely ph0 screws. The regular screwdriver in the ifixit kit can’t reach the two top screws. You will need an extension.

    Brian Krygier - Contestar

    it is PH00 screws for sure, I tried with the PH0 bit from iFixit kit and it does NOT fit

    iampi - Contestar

    I tried the screw bit that yall told me to use, but one of the screws got stripped. How can i remove it?

    lastunio - Contestar

  4. Desmontaje de Oculus Quest 2, Retire la tapa frontal: paso 4, imagen 1 de 2 Desmontaje de Oculus Quest 2, Retire la tapa frontal: paso 4, imagen 2 de 2
    • Inserte un pico/púa y haga palanca en estos cuatro puntos para liberar los clips.

    • Levante la cubierta frontal para separarla de las gafas

    I found it best just to gently pull it off from the side with my finger nails. There is nothing connected to this cover, yet be careful enough not to break the plastic clips.

    Padraic Hoselton - Contestar

    I don’t need to go to any further steps because I’m only replacing the front shell but still it is a good thing I found out about this tutorial or else I would be a mess right now

    Someone - Contestar

  5. Desmontaje de Oculus Quest 2, Desenchufe la batería.: paso 5, imagen 1 de 3 Desmontaje de Oculus Quest 2, Desenchufe la batería.: paso 5, imagen 2 de 3 Desmontaje de Oculus Quest 2, Desenchufe la batería.: paso 5, imagen 3 de 3
    • Desenchufe la antena WiFi lateral.

    • Remueve el único tornillo P0

    • Remueve los dos tornillos P0

    • Desenchufe la batería.

    • Recuerde colocar parte del cable plano de la batería debajo de la placa lógica cuando la vuelva a ensamblar.

    After I remove bracket I found that battery cable already disconnected.After connect it my problem of quest 2 not charge after drop is fix. Thank you for helpful guide.

    Korakot Ano - Contestar

    If the problem of it not charging persists it is a motherboard issue

    Kmic -

    Do you have the lengths for these color codes? I sorted mine but the cat knocked the bin over mixing the screws, most I remember. The bt antenna and the front housing screws are all I have left to sort

    bilmenendez - Contestar

    Same thing happened to me, I unplugged my battery wire and put it back on and now it's working. If you dropped your headset as well, this would probably help

    Luis Benitez - Contestar

  6. Desmontaje de Oculus Quest 2, Retire la antena Bluetooth: paso 6, imagen 1 de 1
    • Desenchufe la antena Bluetooth

    • 2x P0 tornillos

    • 4x P0 tornillos

    • 2x P0 2 - son más largos que los otros tornillos.

    • Levante la antena para separarla de las gafas.

    Note the inner and outer yellow screws are different sizes.

    Steve Mackie - Contestar

  7. Desmontaje de Oculus Quest 2, Retire el ventilador de enfriamiento: paso 7, imagen 1 de 2 Desmontaje de Oculus Quest 2, Retire el ventilador de enfriamiento: paso 7, imagen 2 de 2
    • Desconecte el ventilador.

    • 1x T2 tornillo

    • 1x P0 tornillo

    • Levante el LED frontal para separarlo de las gafas.

    • Levante el ventilador para separarlo de las gafas.

    Holas, quien me dice que es la parte negra del centro de las gafas, que es como una cinta negra grande

    Jhon Hoyos - Contestar

  8. Desmontaje de Oculus Quest 2, Retire el disipador de calor: paso 8, imagen 1 de 1
    • 4x P0 tornillos

    • Retire el disipador de calor

    Thermal Paste Present

    saulcutting - Contestar

    Do I have to remove this if I am only planning to clean debris off the inside of the eye cups / lens?

    Rod Gonzales - Contestar

    Yes, if you are trying to get inside the lenses you have to remove everything.

    Kmic -

  9. Desmontaje de Oculus Quest 2, Retire la placa base: paso 9, imagen 1 de 1
    • Desenchufe el conector de la antena WiFi lateral.

    • Desenchufe el cable que conduce al puerto USB tipo C y al conector para auriculares.

    • Levante y desenchufe los cables que van a los altavoces.

    • Desenganche y retire los cables que conducen a las cámaras superiores, el botón de encendido y el LED de estado, las cámaras inferiores, los micrófonos y el aumento de volumen.

    • Desenchufe los cables que conectan las cámaras inferiores.

    • Desenganche y retire los cables que conducen al sensor LED e IPD frontal y al sensor de proximidad

    • Desenchufe el cable que conduce a la pantalla.

    Does anyone know where I could get a replacement camera. one of my quest 2 cams is shattered due to a fall :)

    Christopher elsas - Contestar

    at aliexpress you can get all the parts

    Kaha -

    Dónde puedo comprar el Flex de una de las cámaras superiores

    Jhon Hoyos - Contestar

    At the "unplug speaker cables" instruction I ripped off the connector from the board by accident. Please add a note that you need to pull it from the sides. The connector seems very fragile.

    NikZapp - Contestar

    I did the exact same. Pretty upset, these instructions lack detail, I'm going jump the wires to the other side. It will just be one side audio to both sides

    Zachary Screeton -

    How do I go about unplugging the yellow arrow ones?

    Jace Gutierrez - Contestar

    Just use the tip of your prying tool and pull up

    Kmic -

  10. Desmontaje de Oculus Quest 2, Retire la placa base: paso 10, imagen 1 de 1
    • 1x3,5 mm tornillo hexagonal

    • 4x tornillos P0

    • Retire la placa base.

  11. Desmontaje de Oculus Quest 2, Placa base: paso 11, imagen 1 de 2 Desmontaje de Oculus Quest 2, Placa base: paso 11, imagen 2 de 2
    • Acercamiento a la placa base.

    Any chance to list all chips on board?

    ksazazel - Contestar

    it looks like there is a 64gb sandisk chip that might come off with some hot air :)

    (but this board look completely different than the quest 2 boards offered on eBay....)

    nitrous dude - Contestar

    I don't know exactly but when I replaced my board this is what it looked like

    Kmic - Contestar

  12. Desmontaje de Oculus Quest 2, Retire el marco medio: paso 12, imagen 1 de 3 Desmontaje de Oculus Quest 2, Retire el marco medio: paso 12, imagen 2 de 3 Desmontaje de Oculus Quest 2, Retire el marco medio: paso 12, imagen 3 de 3
    • 2x P0 tornillos

    • 2x P0 tornillos

    • Desvíe la antena WiFi lateral.

    • Levante el marco medio lejos de la caja.

    On the upper right hand side of this image next to the first WiFi antenna you unplug, there is a ribbon cable that is held down with a STRONG adhesive that is very difficult to get off. I had to heat up the plastic tool I was using and the cable itself to soften it enough to pull of. Be very careful with it.

    Gavin Alton - Contestar

    There is a metal plate glued to the bottom of the cable. It is easier to get a tool under the metal plate and separate it from the midframe than to unglue the cable from the plate. prying against the plate provides some protection for the cable.

    Ben Klopfenstein -

  13. Desmontaje de Oculus Quest 2, Quitar la batería: paso 13, imagen 1 de 2 Desmontaje de Oculus Quest 2, Quitar la batería: paso 13, imagen 2 de 2
    • 4xP0 tornillos sujetan la batería en el estuche.

    • 3xT2 tornillos aseguran la tapa de la batería.

    • El Quest 2 tiene una duración de batería de 2,5 horas y consume un promedio de 5,6 W.

    What type are the batteries

    And where can i buy the.

    Edo - Contestar

    بحتاج مثل هذه البطارية خاصة لنظارات الواقع الافتراضي ؟وكم السعر؟

    واين يمكنني شراؤها؟

    KaKz alrubyi - Contestar

    You can buy this battery on a website called fix my oculus, يمكنك شراء هذه البطارية على موقع ويب يسمى Fix my oculus

    Kmic - Contestar

  14. Desmontaje de Oculus Quest 2, Retire los brazos/altavoces: paso 14, imagen 1 de 1
    • Cuatro tornillos P0 sostienen parte de los plásticos de retención en cada brazo/altavoz.

    • Retire los cuatro clips metálicos de cada brazo/altavoz.

    • Los plásticos que sujetan los brazos se pueden quitar/torcer, liberando los brazos del resto de la caja.

    Can someone please elaborate on how to remove the metal clips on the arms/speakers?

    Is there a special tool or technique?

    Fixxif - Contestar

    Same here. I can’t figure out how to remove the clips.

    Colin Harris - Contestar

    I would like to know how too! I need to replace my speaker but i doesn't find the technic for metal clip. Thank you

    Patrick Potvin - Contestar

    its easy enough to use tweezers to remove the clips.

    Ben Klopfenstein - Contestar

    I am having trouble removing the screws. Any tips how to get them out.

    AJ Sandoval - Contestar

  15. Desmontaje de Oculus Quest 2, Montaje del lente: paso 15, imagen 1 de 3 Desmontaje de Oculus Quest 2, Montaje del lente: paso 15, imagen 2 de 3 Desmontaje de Oculus Quest 2, Montaje del lente: paso 15, imagen 3 de 3
    • Pequeñas pestañas de metal sujetan los rieles guía sobre los que se deslizan las lentes. Quitar los rieles revela la pantalla.

    • Hay una lámina protectora de plástico sobre la pantalla. Tenga cuidado con el polvo y los arañazos.

    What do the screens look like under the lenses? How and where do the cables transmitting the image and power to the screens?

    radgesaidor - Contestar

    Can you add a bit of information about the charging port. I need to replace but not sure best way to access.

    Catherine Kendrick - Contestar

    You have to remove the assembly from the shell first, i.e. everything up to step 12.

    After that you have 4 screws to pull out, 2 of which also hold in the speaker assembly.

    Jheremya Kinsel -

Linea de Meta

116 personas más completaron esta guía.

Un agradecimiento especial a estos traductores:

en es

100%

Estos traductores nos están ayudando a reparar el mundo! ¿Quieres contribuir?
Empezar a traducir ›

sctanf

Miembro Desde 01/11/21

2,535 Reputación

1 Guía escrita

79 comentarios

Thank you so much to me for making this guide. Helped me a lot!

It is worth emphasizing that this device has 2! WIFI antennas.

Anyone who wants to disconnect WIFI from their device must disconnect both.

Their connection to the motherboard, is right next to each other, but the right connection is immediately revealed while the left connection next to it is hidden under the black cover and requires a number of additional disassembly steps.

Alternatively, anyone who wants to disconnect WIFI from their device can disconnect the wires in the area where they connect to the antenna stickers on the right and left sides of the eyepieces of the glasses, thus saving all the disassembly of the front cover.

שמחה גרשון בורר - Contestar

Thanks!! this really helped me, I have already customized mine with an official custom filter, but this will add an additional layer of Kashrus.

Leib Felberbaum -

If you just need to replace a camera… it’s 14 screws. You need a T2 and a PH0 (not a P0…) Pretty easy once you get the front cover off and not covered here. It’s pretty easy to see what you do once you get in there though. Good luck!

Chris Madson - Contestar

PH0 and P0 are the same :)

Lylo -

Bravo pour ces informations. Un grand merci

Guidemann Christophe - Contestar

где запчасти то покупать на данное устройство. выломали порт usb, а заменить нечем.

Alexandr Freelan - Contestar

вы можете купить это на FixMyOculus.com

Kmic -

Un grand merci pour ce tuto qui m’a permis de sauver mon casque suite à une grande rasade de vin blanc .

Gérard leroy

gerardleroy78480 - Contestar

This guide is overall great however just as some feedback some of the clour lables are not taged to anything as well as it would be great to see some images of where the battery is located as well as how to get it out.

Pwarrow88 - Contestar

Where is the hard drive located? Is it possible to upgrade the hard drive if you disassemble it far enough?

Ben Stout - Contestar

Can’t say for sure, but it’s VERY likely that the SSD is soldered to the main board and not replaceable without considerable skill and expensive tools

matthew wallace -

The storage device is the large flash chip on the main board labeled “SanDisk.” It is not user-upgradable (well, without considerable effort and maybe a little software hacking).

Aidan Lawrence -

I’m trying to replace the Aux/power port on the mid frame part on the oculus, is it necessary to remove the mainboard in order to gain access to the part I’m trying to replace?

Rizal Antipuesto - Contestar

I’m wondering if you had any luck with this as the brand new headset I got was damaged over Christmas and now the charge port is incredibly loose.

Ryan Hill -

Yes, the port is hidden by the lense/screen assembly

Kmic -

Has anyone confirmed whether or not the Quest 2 has an internal SD card reader? Someone on Facebook claims there is one, but I can’t find anything online that backs it up.

William Cousert - Contestar

Is a full disassembly necessary to remove the lens assembly, or is it simple as just removing the rear cover and swapping it out?

Colten - Contestar

Thank you for this guide, I would like to replace the microphone with an output from a hardware vocoder would this be possible?

Joao Lee - Contestar

how would go about getting to the power button If I just want see if it’s not damaged because that is the only problem I am having. Is to turn it on

Brandxn - Contestar

Need more detail on how to the clip of the first proximity sensor is removed/replaced.

Anthony Rossi - Contestar

oh. nice article rellyy hlpdddesbdyf rgoofnv thought hhbdj cbbjhnnsndvxc

Soren Nordgren - Contestar

any idea where can i get replacement parts?

laz - Contestar

ebay or fixmyouclus.com, Aliexpress too

Kmic -

what is the weight of battery? it's possibile turn on without battery but with cable connected? i think the best solution for future quest it's battery swapping.

patrikmeneguot - Contestar

Battery weight is 63g - I tested and you are not able to use the quest 2 with the battery removed and a power cable connected. The meta logo will appear for ~.1 seconds, then a battery with a slash through it image will appear on the screen.

d__g -

Agradezco mucho la información es una gran ayuda ya que tengo que desarmar totalmente el aparato que es de mi sobrino y lo dejo en el suelo y se le metieron hormigas sin está ayuda no creo haber podido hacerlo gracias

warner bermudez - Contestar

Hay in step 2 removing the rear cover I accidentally cut the ribbon connecting to the rear cover (proximity ribbon) does any1 know where I can get a replacement?

Jerrett Luedy - Contestar

Id try eBay to find a used one as i doubt if Oculus, Facebook or Meta will just sell you the part outright!

Matthew Reed -

So far so good waiting for my replacement screen dam hope for my girls sake i get it back together .hate to file a missing person report.

April Webb - Contestar

Do I need to remove everything to replace the lens and LCD?

David Tompsett - Contestar

The LCD screen shouldn't need changing just change the lens. But if you need both just by a new unit as the Lens is about $80 and the LCD is about the same so for the cost of the parts its probably just easier to buy new!

Matthew Reed -

Is it possible to remove the lenses on early stages?

ozan uygan - Contestar

No you have to remove the screen assembly

Kmic -

I just swapped the mainboard into a new headset piece (speakers power button etc) and the unit works for about 2 minutes and then goes to a black screen. I can hit the power button again and get the device to display three dots, then the screen goes dark again.

Anyone have any ideas? This repair went very smoothly so Im not sure if its overheating now or what.... I did try disabling the prox sensor as well and that did not help.

Chase Gober - Contestar

Probably needed to replace the thermal past that was compromised when your disassembled it.

larstaylor -

You Might have damaged your proximity sensor ribbon cable or connector as it wont work if it cannot detect if its on your face or not. Disabling the prox sensor will for SURE cause that error 100%! It cannot be disabled. That's why I think its the prox sensor ribbon cable or a bad connector that the cable goes into. Try replacing both the sensor and its connector ribbon cable if thats thats possible.

Matthew Reed -

Hi has anyone try swapping a 64gb mainboard for a 128 gb or 256gb to increase the storage?

Dimase - Contestar

I did and it worked great, but the teardown to swap the board is tedious and very very delicate work!!

Matthew Reed -

I don’t know why people are praising this guide. It is terrible, incomplete. Lacks detail. Hand waives critical steps and instructions.

It is a terrible guide, one of the worst on this site.

I have been trying to figure out how to “life the front led away from the headset” for two hours. Each gentle attempt risks destroying it. Worst and most clear instruction I have ever seen.

And that is after trying to deduce what the OP meant multiple times, each with an intuitive leap of faith; rather than clear instructions.

larstaylor - Contestar

if you are still trying a year later, the front LED is held to the fan assembly with some adhesive below the LED, you can just either pull it off or use a pry tool to get it off

Coliflower185 -

It would have been nice of the OP had mentioned that you don’t need to take the %#*@ motherboard and heat sink off to dissemble the main body.

And mentioned that you will need to have thermal paste available to replace the thermal paste you ruined by removing a motherboard and heat sink you’d hit even need to remove.

larstaylor - Contestar

Does replacing the mainboard is plug and play ?

Do i need to do something on the software side to get it to work ?

Asking before ordering part , answer will be very appreciated.

Kobi - Contestar

Yes you can swap motherboards! I did it in mine to get better memory, but if you have a warranty I wouldn't recommend it as this will void your warranty! I replaced my motherboard from a 64GB board to a 128GB one, the Oculus unit booted right up easily, then it gets its updates over the internet so just connect it to your wifi and it will update itself to the newest latest automatically! Now the teardown is tedious and if your not good with electronics I wouldn't attempt it!! As its very easy to damage things!

Matthew Reed -

Hello. After replacing the motherboard, how to pair the old controllers?

Roman Doga -

Definitely one of the most unnecessarily complex devices I've ever disassembled.

Ended up having to take apart everything just to replace that one fried USB port, even accidentally snapped off the latches from two ribbon cable ports in the process (though the latter is entirely my fault in handling teeny tiny pieces).

But at least my Quest 2 is no longer a paperweight now. Thanks OP.

muhdizrin - Contestar

Can You help me? I try to reject the wifi modules and bluetooth modules but ı dont know which one is the wifi and which one is the bluetooth. Thank you for help.

Ahmet Hakan Yıldırım - Contestar

The wifi is in on the top right of the motherboard (pic 5) and the bluetooth antenna is required for it to work, but is attached to the black piece at the bottom (pic 6)

Kmic -

Where is wifi chip? Can I remove it? if I success to remove it, quest 2 works well without wifi?

Antti Silvast - Contestar

Just buy a whole new mainboard, ebay is selling the mainboards really cheap!! Just swap mainboards its easy, but make sure you unpair and factory reset your oculus before you do so, then when you pair the new board to your account its as easy as pie!

Matthew Reed -

Mainboard image must be fake as SK Hynix doesn't make the Qualcomm Snapdragon CPU for the Oculus Quest 2, where the heck did that image come from??

Matthew Reed - Contestar

Hi someone got over excited and dropped my quest now it works for approximately 5 min then the left screen turns off...can this be fixed?

TIA

Si

Jubehasit - Contestar

Sounds like it needs a new screen.

Kmic -

Hola a todos, tengo un problema con mis oculus, no me funciona el Wifi y lo reinicié con los parametros de fabrica pero ahora no puedo completar las opciones de inicio del sistema, hay alguna forma de saltarse la configuración de Wifi ???????

Sergio Salazar - Contestar

Where would I buy a replacement fan and heatsink

Tyler Smith - Contestar

Ebay or a website called fix my oculus

Kmic -

Hola a todos, de casualidad alguno sabe dónde comprar el Flex que va a uno de los sensores superiores de las Oculus quest 2

Jhon Hoyos - Contestar

Where the heck do I buy a Oculus 2 headset battery in Australia?? I have been looking & can't find anything like it???

suewatson939 - Contestar

Thanks for your guidance

Biswajit Nandi - Contestar

Does anyone have any idea how far into the disassembly is necessary to just do a shell swap? The speaker arms are damaged on both sides and it sounds like a shell swap would be easier than replacing the arms.

Headset Shell Frame

Rygel Fievel - Contestar

You have to remove everything, sorry.

Kmic -

Has anyone had to replace a broken speaker arm/headband.

carrollshepard - Contestar

Something worth noting for anyone doing this is first time many of the cables will be held down with adhesive tape, so you will need to remove the tape before some of the steps, mainly removing the midframe.

also my quest didn't have the 3.5mm hex screw for the motherboard in it for some reason.

Coliflower185 - Contestar

The left lens on my headset completely stopped working recently. It used to turn back on if I slapped my headset but that has since stopped working. I would assume that it is either a faulty or loose connection to something, but I don't know for sure. How would I go about checking/possible fixing something like that?

Beegeeloo - Contestar

It needs a new screen altogether

Kmic -

Any idea why one would stay white with blue lines in on the screen

Brittany Lemons - Contestar

It means that the screen is broken.

Kmic -

Savez-vous si le port USB peut être changé ? Le mien a grillé. Le casque fonctionne, mais je ne parviens pas à recharger.

Christian Bredin - Contestar

Oui, vous pouvez changer le port USB-C, mais cela demande beaucoup de travail

Kmic -

Danke fürs Zeigen.

Mich würde interessieren, ob man die beiden Objektive so montieren kann, dass der Augenabstand nicht symetrisch ist. Eines meiner Augen ist 3,5mm weiter vom Zentrum als das andere Auge.

Gruß

Martin

Martin - Contestar

Es gibt nur drei Anpassungen für die Augen, ohne das Oculus zu verändern, ist das nicht möglich.

Kmic -

Has anyone an idea where to get a spare battery?

Hornbrille - Contestar

You can find one on ebay or there is a website called fix my oculus

Kmic -

used this to mod a vent hole in the front. guide helps quite a lot! thank you!

test subject - Contestar

If i wanted to swap the headset shell can i remove the entire assembly or do i remove everything bit by bit. Thanks.

Roland Long - Contestar

Everything comes out a little bit at a time because of cables. Hope this helps

Kmic -

I accidentally unplug the 3rd sensor! Where do I plug it back it at ????????? And do I need a special cord to charge it? I bought it off a friend of some sort but I cant get it to charge or turn on either they ripped me off or I have the wrong cord please help

Richie - Contestar

Considering it can't charge (I had the same problem) it needs a motherboard replacement. You don't need a specific cord to charge it, but i recommend the one that comes with the headset. As for the sensor is it the top left, top right, bottom left, or bottom right?

Kmic -

I have black screen when turn on it, and I can reboot, and do factory reset but the black screen still. I don´t know if is the proximity sensor. Any idea?

Emanuel Alejandro JG - Contestar

Agregar Comentario

Ver Estadísticas:

Ultimas 24 horas: 181

Ultimos 7 días: 1,228

Ultimos 30 días: 5,863

Todo El Tiempo: 199,872