Repara tus cosas

Derecho a reparar

Tienda

OLPC XO-4 Touch Screen Replacement

Escrito Por: Zach Yasuda (y 7 de otros participantes)
  • Comentarios: 0
  • Favoritos: 1
  • Terminaciones: 2

Dificultad

Moderado

Pasos

11

Tiempo Requerido

15 minutos

Secciones

3

Banderas

1

Featured Student Guide

Guía de Estudiante Destacada

Esta guía fue realizada gracias al duro trabajo de nuestros fantásticos estudiantes y ha sido valorada como excepcionalmente genial por el personal de iFixit.

Introducción

Learn how to replace the display screen on the XO-4 Touch.

Herramientas

Comprar estas herramientas

Partes

No se especificaron partes.

  1. Turn the laptop upside-down, with the handle facing away from you.

    • Turn the laptop upside-down, with the handle facing away from you.

    Traducir

  2. Pull the lock tabs towards the green outer edges of the laptop. Hold the left lock tab in the unlock position until the battery is completely removed in the next step.

    • Pull the lock tabs towards the green outer edges of the laptop.

    • Hold the left lock tab in the unlock position until the battery is completely removed in the next step.

    Traducir

  3. Lift up on the middle of the battery to remove it from the device. Lift up on the middle of the battery to remove it from the device.

    • Lift up on the middle of the battery to remove it from the device.

    Traducir

  4. Remove the two 4mm Phillips #1 screws underneath the screen on the right-hand side. Rotate the screen 180° and remove the other two screws. You will have to put your screwdriver through the handle in order to reach the middle screw for both sides.

    • Remove the two 4mm Phillips #1 screws underneath the screen on the right-hand side.

    • Rotate the screen 180° and remove the other two screws.

    • You will have to put your screwdriver through the handle in order to reach the middle screw for both sides.

    Traducir

  5. El kit de herramientas esencial

    Las herramientas más útiles en nuestro kit más compacto.

    Compra ahora

    El kit de herramientas esencial

    Las herramientas más útiles en nuestro kit más compacto.

    Compra ahora

  6. Remove the green side panel by pressing down on the small green button on the top and sliding the panel up. Repeat the step above for the panel on the other side. Repeat the step above for the panel on the other side.

    • Remove the green side panel by pressing down on the small green button on the top and sliding the panel up.

    • Repeat the step above for the panel on the other side.

    Traducir

  7. Be careful not to pull the bottom too far out because a ribbon cable is under the frame and can easily break.

    • Be careful not to pull the bottom too far out because a ribbon cable is under the frame and can easily break.

    • Gently lift up the lower part of the frame and pull it down to free the screen frame.

    Traducir

  8. Lift the black connector and pull the ribbon cable out by the purple tab, freeing the frame. Lift the black connector and pull the ribbon cable out by the purple tab, freeing the frame.

    • Lift the black connector and pull the ribbon cable out by the purple tab, freeing the frame.

    Traducir

  9. Remove the four 7.62mm screws using a Phillips #1 screwdriver.

    • Remove the four 7.62mm screws using a Phillips #1 screwdriver.

    Traducir

  10. Be careful not to pull the screen out too far. There are two ribbon cables attached to the screen, and they can easily break. Carefully lift the screen out.

    • Be careful not to pull the screen out too far. There are two ribbon cables attached to the screen, and they can easily break.

    • Carefully lift the screen out.

    Traducir

  11. Notice that the laptop in this picture has been turned 180° with the antennas now below the screen. For each ribbon cable, lift up the black connector and gently pull the ribbon cables out by the plastic tabs. For each ribbon cable, lift up the black connector and gently pull the ribbon cables out by the plastic tabs.

    • Notice that the laptop in this picture has been turned 180° with the antennas now below the screen.

    • For each ribbon cable, lift up the black connector and gently pull the ribbon cables out by the plastic tabs.

    Traducir

  12. Remove the screen from the laptop.

    • Remove the screen from the laptop.

    Traducir
Conclusión

To reassemble your device, follow these instructions in reverse order.

2 personas más completaron esta guía.

Autor

con 7 otros colaboradores

Zach Yasuda

Miembro Desde 24/01/13

173 Reputación

2 Guías creadas

Insignias: 10

+ 7 más insignias

Equipo

Cal Poly, Team 3-29, Amido Winter 2013 Miembro de Cal Poly, Team 3-29, Amido Winter 2013

CPSU-AMIDO-W13S3G29

4 Miembros

20 Guías creadas

0 comentarios

Agregar un comentario

Agregar Comentario

Ver Estadísticas:

Ultimas 24 horas: 0

Ultimos 7 días: 1

Ultimos 30 días: 6

Todo El Tiempo: 1,196