Saltar al contenido principal

OLPC XO-4 Touch Back Cover Replacement

Qué necesitas

  1. OLPC XO-4 Touch Back Cover Replacement, Battery: paso 1, imagen 1 de 1
    • Turn the laptop upside-down, with the handle facing away from you.

  2. OLPC XO-4 Touch Back Cover Replacement: paso 2, imagen 1 de 2 OLPC XO-4 Touch Back Cover Replacement: paso 2, imagen 2 de 2
    • Pull the lock tabs towards the green outer edges of the laptop.

    • Hold the left lock tab in the unlock position until the battery is completely removed in the next step.

  3. OLPC XO-4 Touch Back Cover Replacement: paso 3, imagen 1 de 2 OLPC XO-4 Touch Back Cover Replacement: paso 3, imagen 2 de 2
    • Lift up on the middle of the battery to remove it from the device.

  4. OLPC XO-4 Touch Back Cover Replacement, Screen Frame: paso 4, imagen 1 de 3 OLPC XO-4 Touch Back Cover Replacement, Screen Frame: paso 4, imagen 2 de 3 OLPC XO-4 Touch Back Cover Replacement, Screen Frame: paso 4, imagen 3 de 3
    • Remove the two 4mm Phillips #1 screws underneath the screen on the right-hand side.

    • Rotate the screen 180° and remove the other two screws.

    • You will have to put your screwdriver through the handle in order to reach the middle screw for both sides.

  5. OLPC XO-4 Touch Back Cover Replacement: paso 5, imagen 1 de 3 OLPC XO-4 Touch Back Cover Replacement: paso 5, imagen 2 de 3 OLPC XO-4 Touch Back Cover Replacement: paso 5, imagen 3 de 3
    • Remove the green side panel by pressing down on the small green button on the top and sliding the panel up.

    • Repeat the step above for the panel on the other side.

  6. OLPC XO-4 Touch Back Cover Replacement: paso 6, imagen 1 de 1
    • Be careful not to pull the bottom too far out because a ribbon cable is under the frame and can easily break.

    • Gently lift up the lower part of the frame and pull it down to free the screen frame.

  7. OLPC XO-4 Touch Back Cover Replacement: paso 7, imagen 1 de 2 OLPC XO-4 Touch Back Cover Replacement: paso 7, imagen 2 de 2
    • Lift the black connector and pull the ribbon cable out by the purple tab, freeing the frame.

  8. OLPC XO-4 Touch Back Cover Replacement, Screen: paso 8, imagen 1 de 1
    • Remove the four 7.62mm screws using a Phillips #1 screwdriver.

  9. OLPC XO-4 Touch Back Cover Replacement: paso 9, imagen 1 de 2 OLPC XO-4 Touch Back Cover Replacement: paso 9, imagen 2 de 2
    • Be careful not to pull the screen out too far. There are two ribbon cables attached to the screen, and they can easily break.

    • Carefully lift the screen out.

  10. OLPC XO-4 Touch Back Cover Replacement: paso 10, imagen 1 de 3 OLPC XO-4 Touch Back Cover Replacement: paso 10, imagen 2 de 3 OLPC XO-4 Touch Back Cover Replacement: paso 10, imagen 3 de 3
    • Notice that the laptop in this picture has been turned 180° with the antennas now below the screen.

    • For each ribbon cable, lift up the black connector and gently pull the ribbon cables out by the plastic tabs.

  11. OLPC XO-4 Touch Back Cover Replacement: paso 11, imagen 1 de 1
    • Remove the screen from the laptop.

  12. OLPC XO-4 Touch Back Cover Replacement, Back Cover: paso 12, imagen 1 de 1
    • Remove the four 6mm screws using a Phillips #1 screwdriver.

  13. OLPC XO-4 Touch Back Cover Replacement: paso 13, imagen 1 de 2 OLPC XO-4 Touch Back Cover Replacement: paso 13, imagen 2 de 2
    • Rotate the top half of the laptop so that the back cover is facing you.

    • Pull up the tabs on the lower part of the back cover and pull it down and away from the antennas.

    • Remove the back cover by gently lifting it off of the laptop.

Conclusión

To reassemble your device, follow these instructions in reverse order.

Matthew Smith

Miembro Desde 01/25/13

23 Reputación

4 Guías creadas

Equipo

Cal Poly, Team 3-29, Amido Winter 2013 Miembro de Cal Poly, Team 3-29, Amido Winter 2013

CPSU-AMIDO-W13S3G29

4 Miembros

20 Guías creadas

0 comentarios

Agregar Comentario

Ver Estadísticas:

Ultimas 24 horas: 0

Ultimos 7 días: 0

Ultimos 30 días: 4

Todo El Tiempo: 248