Saltar al contenido principal
  1. Apply heat pad to each side of the device.
    • Apply heat pad to each side of the device.

    • When using any heat pad please use some form of padded gloves so you don't burn you fingers.

    • Microwave the pad for 30 seconds so an ample amount of heat is given on all four sides. Do not microwave more than once every two minutes.

  2. Insert the pick between the glass to separate the glass from the device. You can also use the suction cups to help lift the glass. When pulling the screen off the chassis be careful not to cut  the ribbon cable the connect the screen to the logic board. Take your time to pry open the screen from the chassis. In this process you can easily break the screen or crack it.
    • Insert the pick between the glass to separate the glass from the device. You can also use the suction cups to help lift the glass.

    • When pulling the screen off the chassis be careful not to cut the ribbon cable the connect the screen to the logic board.

    • Take your time to pry open the screen from the chassis. In this process you can easily break the screen or crack it.

  3. Pull out the ribbon cable from its connection Once that done move on to remove the ribbon connection from the screen.
    • Pull out the ribbon cable from its connection

    • Once that done move on to remove the ribbon connection from the screen.

  4. Use the plastic pry tool to remove one of the connection. Use the plastic pry tool to remove one of the connection. Use the plastic pry tool to remove one of the connection.
    • Use the plastic pry tool to remove one of the connection.

  5. Kits de Reparación de Batería de iPhone

    Sólo $29.99

    Buy Now

    Kits de Reparación de Batería de iPhone

    Sólo $29.99

    Buy Now
  6. Once down everything is completed.
    • Once down everything is completed.

  7. Before removing the battery from the device be sure not to puncture the battery. Since the battery is a form of acid. Using a plastic pry tool is better than a metal tool when working with wire and soft case battery case. Use a plastic pry tool to remove the battery connector from the logic board.
    • Before removing the battery from the device be sure not to puncture the battery. Since the battery is a form of acid.

    • Using a plastic pry tool is better than a metal tool when working with wire and soft case battery case.

    • Use a plastic pry tool to remove the battery connector from the logic board.

  8. Remove the ribbon located over the battery. Remove the ribbon located over the battery.
    • Remove the ribbon located over the battery.

  9. Theres four screws that attach the battery to the chassis. Use a PH0 Phillips head screwdriver to loosen the screw.
    • Theres four screws that attach the battery to the chassis. Use a PH0 Phillips head screwdriver to loosen the screw.

    • Since the tool using is sharp please use with caution, so that you don't puncture the battery.

  10. Take a plastic pry to to pry out the battery from its casing. The bottom of the battery has adhesive to hold the battery in place. So using enough pressure to pry the battery is ok . Using two tool different plastic pry to can help give you leverage on areas that are hard to get up.
    • Take a plastic pry to to pry out the battery from its casing.

    • The bottom of the battery has adhesive to hold the battery in place. So using enough pressure to pry the battery is ok .

    • Using two tool different plastic pry to can help give you leverage on areas that are hard to get up.

  11. Disconnect the speaker connection. Disconnect the speaker connection.
    • Disconnect the speaker connection.

  12. Pry the speaker out of its housing. Pry the speaker out of its housing. Pry the speaker out of its housing.
    • Pry the speaker out of its housing.

  13. Once done you are complete.
    • Once done you are complete.

Conclusión

To reassemble your device, follow these instructions in reverse order.

Degan Berhe

Miembro Desde 29/08/18

500 Reputación

4 Guías creadas

Equipo

Gateway, Team S1-G4, Luster Fall 2018 Miembro de Gateway, Team S1-G4, Luster Fall 2018

GCC-LUSTER-F18S1G4

5 Miembros

5 Guías creadas

Agregar Comentario

Ver Estadísticas:

Ultimas 24 Horas: 0

Últimos 7 Días: 1

Últimos 30 Días: 2

Todo El Tiempo: 50