Nintendo Wii U Wireless Module Replacement

Esta guía ha sufrido modificaciones. Revisa la última versión sin revisar.

Introducción

The wireless module is a component in the Wii U's wireless connectivity with the gamepad. This guide will show you how to replace this important component of the Wii U.

Qué necesitas

Paso 1 Console Outer Case

Nintendo Wii U Wireless Module Replacement, Console Outer Case: paso 1, imagen 1 de 1

With the bottom of the console facing up, remove the following 6 screws hidden underneath the white square stickers:
Three 5.1mm Phillips #000 screws
Two 6.1mm Tri-wing Y0 screws
One 13.2mm Tri-wing Y1 screw

Traducir

Paso 2

Rotate the console 180 degrees so that the exhaust vents are facing you.
Remove the two 7.1mm Phillips #00 screws.

Traducir

Paso 3

On the side opposite of the exhaust vents, slide the cover faceplate towards the back of the console and pull upwards to release it.

Traducir

Paso 4

On the bottom of the console beneath the previously removed faceplate, remove the three 13.2mm Tri-wing Y1 screws.

Traducir

Paso 5

Nintendo Wii U Wireless Module Replacement: paso 5, imagen 3 de 3

On the back of the console, lift up and release the main top cover.

Traducir

Paso 6 Front Faceplate

Nintendo Wii U Wireless Module Replacement, Front Faceplate: paso 6, imagen 1 de 2

Nintendo Wii U Wireless Module Replacement, Front Faceplate: paso 6, imagen 2 de 2

Rotate the device so that the front plate is facing you.
On each side of the console, remove the 3.5mm Phillips #0 screw connecting the DVD drive to the faceplate.

Traducir

Paso 7

Rotate the device so that the front plate is on the right side and the ribbon cable is visible.
The ribbon cable is connected to the system by a latch which holds in the blue tab. Flip this latch up to unlock it.
Lift up on the blue tab to release the ribbon cable.

Traducir

Paso 8

Remove the front faceplate.

Traducir

Paso 9 DVD Drive

Nintendo Wii U Wireless Module Replacement, DVD Drive: paso 9, imagen 1 de 1

On each side of the DVD drive, remove the two 4.6mm Phillips #0 mounting screws.

Traducir

Paso 10

Rotate the device so that the disc drive slot is visible.
A ribbon cable is attached to the bottom right side of the disc drive. The ribbon cable can rip if it isn't removed properly.
Lift the disc drive out of the mount and turn over to the right so it lies like a book.
Use a spudger to release the ribbon cable.

Traducir

Paso 11

Remove the disc drive.

Traducir

Paso 12 Motherboard

Nintendo Wii U Wireless Module Replacement, Motherboard: paso 12, imagen 1 de 3

Nintendo Wii U Wireless Module Replacement, Motherboard: paso 12, imagen 2 de 3

Nintendo Wii U Wireless Module Replacement, Motherboard: paso 12, imagen 3 de 3

Remove the black plastic shielding by unscrewing connecting screws with a Phillip's Head screwdriver.
You will have to carefully adjust the antenna cables out of the way in order to proceed comfortably.

Traducir

Paso 13

Nintendo Wii U Wireless Module Replacement: paso 13, imagen 3 de 3

The metal cap does not require unscrewing and should lift up with ease.
Unscrew all the screws that outline the perimeter of the board using a Phillips Head (PH1) screwdriver.
Remove the silver shielding plate once all screws are removed. Be careful when pulling it under the affixed antenna cables.

Traducir

Paso 14

At this point, the motherboard should easily separate from the lower tray.

Traducir

Paso 15 Wireless 5ghz Module

Nintendo Wii U Wireless Module Replacement, Wireless 5ghz Module: paso 15, imagen 1 de 3

Nintendo Wii U Wireless Module Replacement, Wireless 5ghz Module: paso 15, imagen 2 de 3

Nintendo Wii U Wireless Module Replacement, Wireless 5ghz Module: paso 15, imagen 3 de 3

Flip the motherboard over to view the underside where the Wii U's wireless modules are located. The Bluetooth module is circled in red.
This module is affixed with strong adhesive, so in order to remove it you will need to wiggle the module with slight force for a couple of minutes.

Traducir