Saltar al contenido principal

Repara tus cosas

Derecho a reparar

Tienda

Introducción

Follow this guide to replace the power and volume button board inside of a Nintendo Switch gaming console.

Note: This guide, and the part we sell, are compatible with the original Nintendo Switch model released in 2017, as well as the newer refreshed model released in 2019 (model numbers HAC-001 and HAC-001(-01), respectively).

  1. Before you begin this repair, make sure the device is completely powered off. Press and hold down the small round button on the back of the Joy Con controller. While you hold down the button, slide  the controller upward.
    • Before you begin this repair, make sure the device is completely powered off.

    • Press and hold down the small round button on the back of the Joy Con controller.

    • While you hold down the button, slide the controller upward.

  2. Continue sliding the controller upward until it's completely removed from the console. Repeat this same process for the other controller. Repeat this same process for the other controller.
    • Continue sliding the controller upward until it's completely removed from the console.

    • Repeat this same process for the other controller.

    • Use a Y00 screwdriver to remove the four 6.3 mm-long screws securing the rear panel.

    • Throughout this repair, keep track of each screw and make sure it goes back exactly where it came from.

  3. Use a JIS 000 screwdriver to remove the following screws securing the rear panel: One 2.5 mm-long screw on the top edge of the device
    • Use a JIS 000 screwdriver to remove the following screws securing the rear panel:

    • One 2.5 mm-long screw on the top edge of the device

    • Two 2.5 mm-long screws on the bottom edge of the device

  4. Use a JIS 000 screwdriver to remove the two 3.8 mm center screws on the sides of the device (one on each side). Use a JIS 000 screwdriver to remove the two 3.8 mm center screws on the sides of the device (one on each side).
    • Use a JIS 000 screwdriver to remove the two 3.8 mm center screws on the sides of the device (one on each side).

  5. Use your finger to flip up the kickstand on the back of the device. If there's a microSD card in the microSD card slot, remove it now before you continue to the next step.
    • Use your finger to flip up the kickstand on the back of the device.

    • If there's a microSD card in the microSD card slot, remove it now before you continue to the next step.

  6. Use a JIS 000 screwdriver to remove the 1.6 mm screw in the kickstand well.
    • Use a JIS 000 screwdriver to remove the 1.6 mm screw in the kickstand well.

  7. Lift the rear panel up from the bottom of the device and remove it. Lift the rear panel up from the bottom of the device and remove it. Lift the rear panel up from the bottom of the device and remove it.
    • Lift the rear panel up from the bottom of the device and remove it.

  8. Use a JIS 000 screwdriver to remove the six 3 mm screws securing the shield plate to the device.
    • Use a JIS 000 screwdriver to remove the six 3 mm screws securing the shield plate to the device.

  9. Use your fingers or a pair of tweezers to peel back the piece of foam on the top edge of the device near the fan exhaust port. Use your fingers or a pair of tweezers to peel back the piece of foam on the top edge of the device near the fan exhaust port.
    • Use your fingers or a pair of tweezers to peel back the piece of foam on the top edge of the device near the fan exhaust port.

  10. Insert a spudger underneath the shield plate along the edge of the device. Pry up to lift the shield plate up. You may feel a bit of resistance. This is normal, since the shield plate is slightly bonded to the heat sink with thermal paste.
    • Insert a spudger underneath the shield plate along the edge of the device.

    • Pry up to lift the shield plate up.

    • You may feel a bit of resistance. This is normal, since the shield plate is slightly bonded to the heat sink with thermal paste.

    • Remove the shield plate.

    • A thick pink thermal compound bridges the gap between the shield plate and the copper heat sink underneath. For best results, whenever the shield plate is removed, refer to our thermal paste guide to remove the old thermal compound and replace it with an appropriate, thick compound such as K5 Pro during reassembly.

  11. Use the point of a spudger to pry the battery connector straight up and out of its socket on the motherboard. Use the point of a spudger to pry the battery connector straight up and out of its socket on the motherboard.
    • Use the point of a spudger to pry the battery connector straight up and out of its socket on the motherboard.

  12. Use a JIS 000 screwdriver to remove the three 3 mm screws securing the heat sink to the motherboard.
    • Use a JIS 000 screwdriver to remove the three 3 mm screws securing the heat sink to the motherboard.

  13. Use the flat end of a spudger or your fingers to carefully peel up the foam that's lightly adhered to the fan. The foam only needs to be peeled back enough to clear the fan.
    • Use the flat end of a spudger or your fingers to carefully peel up the foam that's lightly adhered to the fan.

    • The foam only needs to be peeled back enough to clear the fan.

  14. Use a spudger or your fingers to lift the heatsink up and off the motherboard to remove it. You may feel a bit of resistance. This is normal, since the heat sink is slightly bonded to the CPU with thermal paste. Clean off the old thermal paste from the heat sink and CPU using high-concentration (90% or higher) isopropyl alcohol and a microfiber cloth. Apply new thermal paste to the CPU before reassembly.
    • Use a spudger or your fingers to lift the heatsink up and off the motherboard to remove it.

    • You may feel a bit of resistance. This is normal, since the heat sink is slightly bonded to the CPU with thermal paste.

    • Clean off the old thermal paste from the heat sink and CPU using high-concentration (90% or higher) isopropyl alcohol and a microfiber cloth. Apply new thermal paste to the CPU before reassembly.

  15. Use an opening tool, spudger, or your fingernail to flip up the small, hinged locking flap on the fan cable ZIF connector. Use an opening tool, spudger, or your fingernail to flip up the small, hinged locking flap on the fan cable ZIF connector.
    • Use an opening tool, spudger, or your fingernail to flip up the small, hinged locking flap on the fan cable ZIF connector.

  16. Use a pair of tweezers to pull the fan cable straight out of its connector on the motherboard. Use a pair of tweezers to pull the fan cable straight out of its connector on the motherboard.
    • Use a pair of tweezers to pull the fan cable straight out of its connector on the motherboard.

  17. Use a JIS 000 screwdriver to remove the three 4.8 mm screws securing the fan.
    • Use a JIS 000 screwdriver to remove the three 4.8 mm screws securing the fan.

  18. Use a pair of tweezers or your fingers to lift the fan straight up and remove it from the device. Compare your new replacement part to the original part. You may need to transfer remaining components (such as the rubber bushings) to the new part before installing.
    • Use a pair of tweezers or your fingers to lift the fan straight up and remove it from the device.

    • Compare your new replacement part to the original part. You may need to transfer remaining components (such as the rubber bushings) to the new part before installing.

  19. Use a spudger to flip up the small black locking flap on the power/volume ribbon cable ZIF connector. Use a spudger to flip up the small black locking flap on the power/volume ribbon cable ZIF connector.
    • Use a spudger to flip up the small black locking flap on the power/volume ribbon cable ZIF connector.

  20. Use the flat end of a spudger to pry up the tapped down power/volume ribbon cable.
    • Use the flat end of a spudger to pry up the tapped down power/volume ribbon cable.

  21. Remove the power/volume board with a pair of blunt nose tweezers. Remove the power/volume board with a pair of blunt nose tweezers.
    • Remove the power/volume board with a pair of blunt nose tweezers.

Conclusión

To reassemble your device, follow these instructions in reverse order.

10 personas más completaron esta guía.

Blake Klein

Miembro Desde 29/01/17

61,296 Reputación

57 Guías creadas

Great guide. Just repaired my daughters Switch by replacing power button.

William Flo - Contestar

I replaced the cable and still have the same issue, volume up button don't work and volume down is volume up, and it's always kn

nem37g - Contestar

Agregar Comentario

Ver Estadísticas:

Ultimas 24 horas: 19

Ultimos 7 días: 76

Ultimos 30 días: 302

Todo El Tiempo: 8,909