Esta versión puede contener ediciones incorrectas. Cambiar a la última instantánea verificada.
Qué necesitas
-
-
Retira los dos tornillos Phillips que fijan la tapa de la batería a la parte posterior de la consola portátil.
-
Quita la tapa de la batería de la parte posterior de la DSi XL.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the four rubber screw covers on the lower case by prying them up with a push pin.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the following seven Phillips screws that secure the lower case to the rest of the DSi XL:
-
Four silver 5.3 mm screws
-
Two black 5.3 mm screws
-
One black 2.5 mm screw
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Insert a spudger between the upper and lower case at the bottom left corner of the DSi.
-
Slide the spudger along the bottom edge of the upper case to release the latches securing the upper case to the lower case.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Lift the lower case from the front edge.
-
Rotate the lower case away from the DSi.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Using a spudger, pry the SD card/right shoulder button connector off its socket.
-
Pry the volume button/left shoulder button connector off its socket on the motherboard with a spudger.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Lift the Wi-Fi board up off its socket on the motherboard.
-
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Use a spudger to pry the microphone cable off the motherboard.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Using the flat end of a spudger, flip up the retaining flap on the camera ribbon ZIF connector.
-
Use the pointed end of a spudger to pull the camera ribbon from the ZIF connector.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Using the flat end of a spudger, flip up the retaining flap on the touchscreen cable ZIF connector.
-
With the pointed end of the spudger, pull the touchscreen cable from its connector on the motherboard.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Using the flat end of a spudger, flip up the retaining flap on the backlight cable ZIF connector.
-
With the pointed end of the spudger, pull the backlight cable from its connector on the motherboard.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Using the flat end of a spudger, flip up the retaining flap on the lower display data cable ZIF connector.
-
With the pointed end of the spudger, pull the lower display data cable from its connector on the motherboard.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Using the flat end of a spudger, flip up the retaining flap on the ZIF connector for the D-Pad/power button cable.
-
With the pointed end of the spudger, pull the D-Pad/power button cable from its connector on the motherboard.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Using the flat end of the spudger, pry the battery cable up off its socket on the motherboard.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the screws securing the motherboard to the upper case:
-
A single 2.5 mm silver Phillips screw
-
Four 3.7 mm black Phillips screws
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Deroute the microphone and antenna cables through the slot in the motherboard.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Using the flat end of a spudger, flip up the retaining flap on the upper display data cable ZIF connector.
-
With the pointed end of the spudger, pull the upper display data cable from its connector on the underside of the motherboard.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
With the console still upside-down, open the DSi XL slightly.
-
Push the lower display away from the upper case.
-
Remove the lower display from the DSi XL.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Insert a spudger between the touchscreen and top right corner of the display.
-
Slide the spudger down the right side of the display to free the edge of the touchscreen.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Continue around the bottom right corner of the display with the spudger.
-
Slide the spudger along the bottom edge of the touchscreen to separate it from the display.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Continue around the bottom left corner of the display with a spudger.
-
Slide the spudger along the left edge of the touchscreen to remove it from the display.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
With three sides freed, remove the touchscreen from the lower display.
-
Cancelar: No complete esta guía.
15 personas más completaron esta guía.
3 comentarios
Great tutorial, I completely missed the fact that the lower screen is TWO screens: the touchscreen and the proper screen. Nailed it!!
Step 16 = whole socket came off the motherboard with the least amount of effort. Tried soldering new contacts but too fine. Device now only good for parts.