Saltar al contenido principal
  1. Este paso está sin traducir. Ayuda a traducirlo

    Remove the cartridge from the console. Use a Phillips #00 Screwdriver to remove the screw securing the battery door to the rear case. Remove the battery door.
    • Remove the cartridge from the console.

    • Use a Phillips #00 Screwdriver to remove the screw securing the battery door to the rear case.

    • Remove the battery door.

  2. Este paso está sin traducir. Ayuda a traducirlo

    Use a plastic opening tool or spudger to pry out the battery from the bottom. If a plastic open tool or spudger isn't available, your fingernails may work.
    • Use a plastic opening tool or spudger to pry out the battery from the bottom. If a plastic open tool or spudger isn't available, your fingernails may work.

  3. Este paso está sin traducir. Ayuda a traducirlo

    Remove the battery from the Nintendo DS.
    • Remove the battery from the Nintendo DS.

  4. Este paso está sin traducir. Ayuda a traducirlo

    Remove the seven Y00 screws located on the back.
    • Remove the seven Y00 screws located on the back.

    • It might be helpful to remove the strap from the hole to access the top left screw.

  5. Este paso está sin traducir. Ayuda a traducirlo

    With your hands, pry the back panel off the main case. Separate the back from the front, and set it aside. Separate the back from the front, and set it aside.
    • With your hands, pry the back panel off the main case.

    • Separate the back from the front, and set it aside.

  6. Este paso está sin traducir. Ayuda a traducirlo

    Using a Phillips #00 screwdriver, remove the four screws on the circuit board.
    • Using a Phillips #00 screwdriver, remove the four screws on the circuit board.

    • Be careful NOT to slip with the screwdriver, you can damage the circuit board!

  7. Este paso está sin traducir. Ayuda a traducirlo

    Unlock the two large ribbon cables by moving the black clip up. Carefully pull the ribbon cables down and out with your fingers. Do not use pliers to pull the cables, as they can be damaged easily.
    • Unlock the two large ribbon cables by moving the black clip up.

    • Carefully pull the ribbon cables down and out with your fingers.

    • Do not use pliers to pull the cables, as they can be damaged easily.

  8. Este paso está sin traducir. Ayuda a traducirlo

    Locate the two small ribbon cables, beneath the rightmost large ribbon cable. Slide the locks for the small ribbon cables down to the side, and remove the cables.
    • Locate the two small ribbon cables, beneath the rightmost large ribbon cable.

    • Slide the locks for the small ribbon cables down to the side, and remove the cables.

    • It may be useful to use tweezers to remove the small ribbon cables.

    • Be careful not to damage the delicate ribbon cables.

  9. Este paso está sin traducir. Ayuda a traducirlo

    Locate the Wifi antenna pigtail connector. Remove the antenna by grasping it at the head with tweezers. Using a slight rocking motion, pull up to dislodge the connector.
    • Locate the Wifi antenna pigtail connector.

    • Remove the antenna by grasping it at the head with tweezers. Using a slight rocking motion, pull up to dislodge the connector.

  10. Este paso está sin traducir. Ayuda a traducirlo

    Feed the ribbon cables through the opening on the board.
    • Feed the ribbon cables through the opening on the board.

    • Pull up and remove the circuit board, and set it aside.

Linea de Meta

15 personas más completaron esta guía.

kingdesmond

Miembro Desde 27/10/09

1,859 Reputación

1 Guía escrita

Equipo

Cal Poly, Team 18-3, Maness Fall 2009 Miembro de Cal Poly, Team 18-3, Maness Fall 2009

CPSU-MANESS-F09S18G3

4 Miembros

20 Guías creadas

This was really helpful. Thank you!

Jess Anderson - Contestar

Agregar Comentario

Ver Estadísticas:

Ultimas 24 horas: 2

Ultimos 7 días: 25

Ultimos 30 días: 92

Todo El Tiempo: 22,652