Saltar al contenido principal

Repara tus cosas

Derecho a reparar

Tienda

  1. Desatornilla los dos tornillos de 4.2 mm que están localizados arriba de la cubierta. Los tornillos tienen arandelas(rondananas) de seguridad que previenen que los tornillos caigan de la cubierta . Se levantaran los tornillos, no es necesario remover las arandelas para esta guia de reparacion
    • Desatornilla los dos tornillos de 4.2 mm que están localizados arriba de la cubierta.

    • Los tornillos tienen arandelas(rondananas) de seguridad que previenen que los tornillos caigan de la cubierta . Se levantaran los tornillos, no es necesario remover las arandelas para esta guia de reparacion

  2. Pon el dispositivo hacia abajo. Usa la herramienta de plástico, para ir removiendo la cubierta, empieza desde la ranura derecha de la cubierta.
    • Pon el dispositivo hacia abajo.

    • Usa la herramienta de plástico, para ir removiendo la cubierta, empieza desde la ranura derecha de la cubierta.

    • Manten el borde de la cubierta para asegurar de que no vuelva a encajar.

  3. Inserta la herramienta de plástico en la apertura localizada en el lado derecho de la batería. Empuja la bateria fuera de la carcasa. Levanta y retira la bateria fuera de la carcasa.
    • Inserta la herramienta de plástico en la apertura localizada en el lado derecho de la batería.

    • Empuja la bateria fuera de la carcasa.

    • Levanta y retira la bateria fuera de la carcasa.

  4. Este paso está sin traducir. Ayuda a traducirlo

    Using tweezers pull out the rubber bumpers that are located at the top of the device on either side of the game cartridge compartment. Using tweezers pull out the rubber bumpers that are located at the top of the device on either side of the game cartridge compartment.
    • Using tweezers pull out the rubber bumpers that are located at the top of the device on either side of the game cartridge compartment.

  5. Este paso está sin traducir. Ayuda a traducirlo

    Remove the six 6.2 mm screws using a Phillips #00 screwdriver Remove the six 6.2 mm screws using a Phillips #00 screwdriver
    • Remove the six 6.2 mm screws using a Phillips #00 screwdriver

  6. Este paso está sin traducir. Ayuda a traducirlo

    Remove the 2.3 mm screw located above the game cartridge slot with a Phillips #00 screwdriver.
    • Remove the 2.3 mm screw located above the game cartridge slot with a Phillips #00 screwdriver.

  7. Este paso está sin traducir. Ayuda a traducirlo

    Make sure the SD card has been removed. With a plastic opening tool pry off the lower case starting at the bottom edge and working around the perimeter. Two ribbon cables connect the case to the circuit board. Be careful to not pull the case too hard and rip the ribbon cables. Two ribbon cables connect the case to the circuit board. Be careful to not pull the case too hard and rip the ribbon cables.
    • Make sure the SD card has been removed. With a plastic opening tool pry off the lower case starting at the bottom edge and working around the perimeter.

    • Two ribbon cables connect the case to the circuit board. Be careful to not pull the case too hard and rip the ribbon cables.

  8. Este paso está sin traducir. Ayuda a traducirlo

    Remove the ribbon cables located underneath the left and right bumpers by prying up the base of the cables with a plastic opening tool. Completely remove the lower case from the rest of the device and set aside. Completely remove the lower case from the rest of the device and set aside.
    • Remove the ribbon cables located underneath the left and right bumpers by prying up the base of the cables with a plastic opening tool.

    • Completely remove the lower case from the rest of the device and set aside.

  9. SALTEA LA ACTUALIZACIÓN

    Ahorra reparando con un kit todo en uno.

    Compra Kits de Reparación

    SALTEA LA ACTUALIZACIÓN

    Ahorra reparando con un kit todo en uno.

    Compra Kits de Reparación
  10. Este paso está sin traducir. Ayuda a traducirlo

    Position the device such that the game cartridge slot is located at the top. Locate the circle pad on the right side of the device.
    • Position the device such that the game cartridge slot is located at the top.

    • Locate the circle pad on the right side of the device.

    • Remove the two 7.5 mm screws on the upper left and the bottom right corners.

  11. Este paso está sin traducir. Ayuda a traducirlo

    Using a plastic opening tool pop off the circle pad joystick. Do not use excessive force with the plastic opening tool. There is a ribbon attaching the circle pad joystick to the motherboard that will remain attached.
    • Using a plastic opening tool pop off the circle pad joystick.

    • Do not use excessive force with the plastic opening tool. There is a ribbon attaching the circle pad joystick to the motherboard that will remain attached.

    • There is a loose washer located in between the circle pad joystick and the circle pad. Use caution and do not lose this piece.

  12. Este paso está sin traducir. Ayuda a traducirlo

    Using the flat head side of the spudger carefully lift up the retaining flap that attaches the circle pad ribbon to the motherboard. Remove the ribbon and circle pad joystick.
    • Using the flat head side of the spudger carefully lift up the retaining flap that attaches the circle pad ribbon to the motherboard.

    • Remove the ribbon and circle pad joystick.

  13. Este paso está sin traducir. Ayuda a traducirlo

    Position the device such that the game cartridge slot is located at the top. Locate the IR board located on the upper right side of the motherboard.
    • Position the device such that the game cartridge slot is located at the top.

    • Locate the IR board located on the upper right side of the motherboard.

    • The IR board is installed upside-down in these photos by mistake. Installing it this way will result in your DS failing to start. Note the orientation of your IR board before you remove it, and reinstall it the same way.

    • Remove the IR board with a plastic opening tool by inserting the tool below the IR board and gently prying up.

  14. Este paso está sin traducir. Ayuda a traducirlo

    Using a plastic opening tool, pry off the Wi-Fi board. The Wi-Fi board will still be connected by a wire and it is not necessary to completely remove it for this step. Simply place it out of the way for this step.
    • Using a plastic opening tool, pry off the Wi-Fi board.

    • The Wi-Fi board will still be connected by a wire and it is not necessary to completely remove it for this step. Simply place it out of the way for this step.

  15. Este paso está sin traducir. Ayuda a traducirlo

    Locate the volume switch on the right side of the motherboard next to the circle pad joystick. Using tweezers, carefully remove the volume board from the casing. It will still be attached to the motherboard by a ribbon cable.
    • Locate the volume switch on the right side of the motherboard next to the circle pad joystick.

    • Using tweezers, carefully remove the volume board from the casing. It will still be attached to the motherboard by a ribbon cable.

  16. Este paso está sin traducir. Ayuda a traducirlo

    Using the flat head side of the spudger carefully lift up the flap that attaches the volume board ribbon to the motherboard.
    • Using the flat head side of the spudger carefully lift up the flap that attaches the volume board ribbon to the motherboard.

    • Remove the volume board and set aside.

  17. Este paso está sin traducir. Ayuda a traducirlo

    Remove the black plastic pieces from the lower left and right hand corners with either your fingers or tweezers. You can also remove these pieces easily by carefully lifting up the 3DS and holding it upside-down.   They normally fall right out, but don't lose them!
    • Remove the black plastic pieces from the lower left and right hand corners with either your fingers or tweezers.

    • You can also remove these pieces easily by carefully lifting up the 3DS and holding it upside-down. They normally fall right out, but don't lose them!

  18. Este paso está sin traducir. Ayuda a traducirlo

    Using the flat head side of the spudger carefully lift up the flap that attaches the two smaller ribbons to the motherboard. These flaps are located on the top right and bottom right side of the motherboard. Remove the ribbons from the flap.
    • Using the flat head side of the spudger carefully lift up the flap that attaches the two smaller ribbons to the motherboard.

    • These flaps are located on the top right and bottom right side of the motherboard.

    • Remove the ribbons from the flap.

  19. Este paso está sin traducir. Ayuda a traducirlo

    Using the flat head side of the spudger carefully lift up the flaps that attach the wider ribbons to the motherboard. For the wider ribbons make sure to lift the flaps from the white side. Remove the ribbons from the opened flaps.
    • Using the flat head side of the spudger carefully lift up the flaps that attach the wider ribbons to the motherboard.

    • For the wider ribbons make sure to lift the flaps from the white side.

    • Remove the ribbons from the opened flaps.

  20. Este paso está sin traducir. Ayuda a traducirlo

    Using the flat head side of the spudger carefully lift up the flap that attaches the ribbon to the motherboard. For this flap lift from the black side.
    • Using the flat head side of the spudger carefully lift up the flap that attaches the ribbon to the motherboard.

    • For this flap lift from the black side.

    • Remove the ribbon from the flap.

    • Reassembly: This wide ribbon is the one with the BLACK STRIPE and goes on the upper (visible) side of the motherboard during reassembly.

  21. Este paso está sin traducir. Ayuda a traducirlo

    Remove ten 5.5 mm screws that are located around the face of the motherboard. Remove ten 5.5 mm screws that are located around the face of the motherboard.
    • Remove ten 5.5 mm screws that are located around the face of the motherboard.

  22. Este paso está sin traducir. Ayuda a traducirlo

    The motherboard will still be attached at the top right hand corner so do not completely detach it at this point. Carefully lift the board straight up just enough to clear the two plastic mounts located near the top corners of the cartridge slot.
    • The motherboard will still be attached at the top right hand corner so do not completely detach it at this point.

    • Carefully lift the board straight up just enough to clear the two plastic mounts located near the top corners of the cartridge slot.

    • Gently flip the motherboard over the top side.

  23. Este paso está sin traducir. Ayuda a traducirlo

    Using the flat head side of the spudger carefully lift up the flap that attaches the wider ribbon on the upper right side to the motherboard. Make sure to lift the flap from the white side.
    • Using the flat head side of the spudger carefully lift up the flap that attaches the wider ribbon on the upper right side to the motherboard.

    • Make sure to lift the flap from the white side.

    • Remove the ribbon from the opened flap.

    • Set the motherboard aside.

  24. Este paso está sin traducir. Ayuda a traducirlo

    Open the device's hinge. Gently press upward on the touchscreen until it separates from the casing.
    • Open the device's hinge.

    • Gently press upward on the touchscreen until it separates from the casing.

Linea de Meta

49 personas más completaron esta guía.

Charlene Donlon

Miembro Desde 08/04/14

8,720 Reputación

8 Guías creadas

Equipo

Cal Poly, Team 9-13, Regan Spring 2014 Miembro de Cal Poly, Team 9-13, Regan Spring 2014

CPSU-REGAN-S14S9G13

5 Miembros

21 Guías creadas

what if you need to replace the screen on the top housing? what is it called.

kerriereed - Contestar

Is the bottom LCD screen of the Nintendo 3ds xl, the same as the one in the NEW Nintendo 3ds xl?

Looking for what part to buy.

markknobel - Contestar

Bit old, but did you figure out the answer which to buy?

White -

Very detailed and easy to use step by step thanks. However, after reassembly after I switch the power button on it starts and then a flash and it trips out? Obviously a fault somewhere but not sure where to start.? Any thoughts appreciated.

Pete Mason - Contestar

That's to do with a part this tutorial skips: you need to put some insulation between the new screen and the motherboard. That's what that orange film is on the back of the screen in the photos. When replacing, you can easily (carefully) remove that film and stick it onto the back of the new screen, no problem. Or you can put some other sort of adhesive to create some insulation between the screen and motherboard. Hope this helps.

Albert Wiltfong -

Agregar Comentario

Ver Estadísticas:

Ultimas 24 horas: 12

Ultimos 7 días: 71

Ultimos 30 días: 372

Todo El Tiempo: 65,615