Introducción
Esta guía te permitirá reparar un botón deslizante roto en su Nintendo 3DS XL 2015. Si su botón deslizante ya no funciona bien o no funciona, esta es la guía para ti. Todo lo que necesitarás es un nuevo botón deslizante, unos cuantos destornilladores y, con un poco de paciencia, tu 3DS volverá a tener una funcionalidad completa.
Qué necesitas
-
-
Gire el dispositivo de manera que la cubierta posterior quede hacia usted y ubique los dos tornillos en la parte superior.
-
Con el destornillador Phillips # 000, afloje los tornillos de la cubierta posterior.
-
Haga palanca suavemente en las pestañas del lateral del dispositivo con el spudger de metal o la uña de su pulgar y levante la cubierta posterior.
-
-
-
-
Retire los dos topes de goma en la parte posterior del dispositivo con una tachuela.
-
Con el destornillador Phillips # 00, retire los 8 tornillos que sujetan la cubierta inferior a la placa base.
-
Levante la cubierta inferior, asegurándose de no desconectar los dos conectores ZIF para los botones L / R en la parte posterior del dispositivo.
-
-
-
Con la punta del spudger, levante suavemente la tapa del conector ZIF para liberar el cable del botón deslizante.
what am i supposed to do to get the rest of it off? there's a whole part of the circle pad missing in these steps.
-
-
-
Retire el conjunto de botón deslizante anterior y coloque el nuevo conjunto de botón deslizante. A continuación inserte el cable nuevamente en el conector ZIF abierto y ciérrelo con el spudger.
-
Asegúrese de que el componente interno del botón deslizante esté orientado correctamente con un destornillador pequeño o un spudger.
-
Coloque suavemente el nuevo botón deslizante en su lugar y asegúrelo con los tornillos.
No where does this Mention the 3 different sized screws and where they go after disassemble.
Great guide, it could also do with how to replace the rubber top half of the circle pad too. I've also done this. From the photo in step 8, there's a thin split plastic washer underneath the underside of the circle pad still attached to the 3DS. You can carefully slide this washer out through it's split, then you can remove the upper half of the circle pad by carefully sliding one prong of the C shape through the hole, sliding it through going round, then the other prong will side out and it will be removed. To replace, do it in reverse, but it's very fiddly sliding the split washer back into place, but it can be done with tweezers. On all 3DSs I've opened, the notch on the C shape on the underside is facing down towards the bottom, on this photo it's shown facing the top, but I don't know if it makes any difference. This applies to both old and new 3DS XL and I imagine applies to others too.
-
Para volver a armar tu dispositivo, sigue estas instrucciones en orden inverso.
Para volver a armar tu dispositivo, sigue estas instrucciones en orden inverso.
Cancelar: No complete esta guía.
17 personas más completaron esta guía.
Un agradecimiento especial a estos traductores:
100%
Estos traductores nos están ayudando a reparar el mundo! ¿Quieres contribuir?
Empezar a traducir ›
5 comentarios
oh my gosh this is the best guide my grand-son and i fixed his sons 3DS he is so happy
Thanks for the guide! I needed to replace the internal component of the circle pad as well, as the rubber pad came off mine. @thirtyninester 's comment on Step 8 helped! Thanks to that comment as well!
Help! I'm stuck on Step 5. Upper leftmost screw refuses to come out and I can't tell whether I've worn down the screwhead or the screwdriver. Removal advice please. Otherwise my only recourse may be to replace the entire system. Just transfer everything datawise and be done with it. It'd be a shame if I had to admit I spent $90+ on parts & tools for nothing just for it to come to this. And I don't even want to think about how much a new unit will cost on the secondhand market. I'll be lucky to find one at it's original MSRP.
Hey,
you could try to use a slightly larger screwdriver and see if the screw comes out. Otherwise you have to drill the screw out which is probably still better/cheaper than replacing everything. Hope this helps!