Esta versión puede contener ediciones incorrectas. Cambie a la última instantánea verificada.
Qué necesitas
-
Este paso está sin traducir. Ayuda a traducirlo
-
Gently pry and lift the left motherboard shield off.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove one 3.5 mm J000 screw securing the right motherboard shield.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Gently lift the right motherboard shield off with the tip of a spudger.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Carefully disconnect the red connector with tweezers.
-
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove four 3.5 mm J000 screws securing the motherboard.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Gently pull the port side cover away from the motherboard.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove four 6 mm J000 screws securing the tripod plate.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Carefully lift the tripod plate from the backside of the camera and slide out the grounding clip from under the lens mount.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove three 6 mm J000 screws securing the image sensor.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Carefully lift the image sensor plate out of the camera.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Manually pop up flash by inserting a screw driver to the left of the viewfinder and pressing on the metal lever.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove two 3 mm J000 screws securing the front cover.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove one 8.5 mm J000 screw from the battery compartment.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove one 4 mm J000 screw securing the top case (under right strap hook).
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove one 4 mm J000 screw securing the top case (under left strap hook).
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the sticker covering the diopter adjust screw.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove one 8.0 mm J000 screw.
-
Remove the Diopeter Adjust.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the Black, Yellow, Green cable from the top case board.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove two 6.5 mm J000 screws securing the viewfinder.
-
Remove the viewfinder cover.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove one 3 mm J000 screw from the bottom left side of the camera.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove two 6 mm J000 screws from the left of the shutter.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove two 6.5 mm J000 screws from beneath the lens mount.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove two screws from just below and to the sides of the viewfinder.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove one 5 mm J000 screw from the top right of the camera.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Carefully peel back ribbon cable on the bottom left of camera.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the left front ribbon cable from top right of circuit board.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Pull out ribbon cable from circuit asembly near front left of device.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Disconnected ribbon cable at rear right of viewfinder.
-
Cancelar: No complete esta guía.
5 personas más completaron esta guía.