Saltar al contenido principal

Introducción

Make sure to have your soldering iron ready prior to replacing the screen. This will make the process go faster as the time it takes to heat the soldering iron varies.

  1. Nikon D5200 Screen Replacement, Screen: paso 1, imagen 1 de 3 Nikon D5200 Screen Replacement, Screen: paso 1, imagen 2 de 3 Nikon D5200 Screen Replacement, Screen: paso 1, imagen 3 de 3
    • Fully open the LCD panel so that its screws are easily accessible.

    • Remove the two 2.5 mm screws from the outside edge of the screen casing, and the two 3.5 mm screws from the inside edge.

  2. Nikon D5200 Screen Replacement: paso 2, imagen 1 de 3 Nikon D5200 Screen Replacement: paso 2, imagen 2 de 3 Nikon D5200 Screen Replacement: paso 2, imagen 3 de 3
    • Pry open the plastic casing using the opening tool or by hand.

  3. Nikon D5200 Screen Replacement: paso 3, imagen 1 de 3 Nikon D5200 Screen Replacement: paso 3, imagen 2 de 3 Nikon D5200 Screen Replacement: paso 3, imagen 3 de 3
    • Use the plastic opening tool to pop up the latch holding the ribbon cable on the right side of the circuit board, and remove it.

    • Use the plastic opening tool to pry the ribbon cable on the left side of the circuit board up and off of its socket.

  4. Nikon D5200 Screen Replacement: paso 4, imagen 1 de 2 Nikon D5200 Screen Replacement: paso 4, imagen 2 de 2
    • Using tweezers, unplug the smaller cable.

  5. Nikon D5200 Screen Replacement: paso 5, imagen 1 de 2 Nikon D5200 Screen Replacement: paso 5, imagen 2 de 2
    • Desolder the three small wires on the left side of the circuit board.

    • Soldering irons become very hot when in use. Take all necessary precautions to avoid injury.

  6. Nikon D5200 Screen Replacement: paso 6, imagen 1 de 3 Nikon D5200 Screen Replacement: paso 6, imagen 2 de 3 Nikon D5200 Screen Replacement: paso 6, imagen 3 de 3
    • Using a spudger, remove the display from its casing.

Conclusión

To reassemble your device, follow these instructions in reverse order.

13 personas más completaron esta guía.

Alexander Corn

Miembro Desde 26/08/15

1,211 Reputación

5 Guías creadas

Equipo

USF Tampa, Team 3-1, Eyestone Fall 2015 Miembro de USF Tampa, Team 3-1, Eyestone Fall 2015

USFT-EYESTONE-F15S3G1

4 Miembros

5 Guías creadas

8 comentarios

Do I need to de-solder if I'm just replacing the window glass?

isaac - Contestar

To isaac: no. The exterior glass is separate from the LCD.

Joseph Morris - Contestar

Do you recommend the replacent for LCD sold on Ebay?

g_atki - Contestar

Where did you find the replacement screen? The one I ordered that says it's for the d5200 is not the same as the one in it or in your pictures.

Heather Miller - Contestar

How do you disconnect the multi-plug that is shown connected in image 4 and disconnected in image five? Does it unclip or slide out?

Amanda Bruyninckx - Contestar

Agregar Comentario

Ver Estadísticas:

Ultimas 24 horas: 4

Ultimos 7 días: 19

Ultimos 30 días: 80

Todo El Tiempo: 10,466