Introducción

You will be desoldering the circuit board of the camera.

  1. Place thumb on the battery cover panel on the bottom of the device.
    • Place thumb on the battery cover panel on the bottom of the device.

    • Slide the panel to the right away from the camera.

    Agregar Comentario

  2. Slide the orange latch outward towards the corner of the camera.
    • Slide the orange latch outward towards the corner of the camera.

    • The battery should pop out.

    • Remove the battery and reattach the cover.

    Agregar Comentario

    • After removing the battery, unscrew the four 3.10mm screws on the side opposite the buttons.

    Agregar Comentario

    • Unscrew the three 4.05mm screws on the bottom of the camera below the lens.

    Agregar Comentario

    • Unscrew the two 4.05mm screws on the side next to the buttons.

    Agregar Comentario

  3. Reparte el espíritu de reparación esta Navidad
    Obtén $12 de descuento en tu compra de $50 o más con el código FIXMAS12
    Reparte el espíritu de reparación esta Navidad
    Obtén $12 de descuento en tu compra de $50 o más con el código FIXMAS12
    • Gently wedge the flat end of the spudger between the back case and the wrist-strap mount.

    • The wrist-strap mount is the thin metal piece on the side of the camera. Your camera may have the wrist-strap attached, but you will not need to remove it to continue.

    • Carefully pry the back case away from the camera and then gently lift it off.

    Agregar Comentario

    • Having removed the back case, the LCD screen should be sitting loosely on the camera, attached only by a wide ribbon and a narrow ribbon.

    • The ribbons are connected to and held in place by small plastic latches.

    • To remove the wide ribbon, gently pry the spudger underneath the black plastic latch where the ribbon connects and lift up. The ribbon should slide out easily.

    • Repeat the same process with the smaller ribbon, this time looking for a light blue latch.

    Agregar Comentario

    • Gently remove the LCD screen.

    Agregar Comentario

    • After removing the LCD screen, unscrew the four 3.8mm screws that hold down the metal plate

    • Unscrew the 2.5mm screw next to the wrist-strap mount.

    Agregar Comentario

    • Position the camera with the lens facing down and the shutter button facing you.

    • Lift the metal plate away from the camera without removing it fully. There is a ribbon attaching the edge of the plate to the camera.

    • The ribbon is being held in place by a black latch.

    • Carefully pry the spudger under the black latch and lift gently upward. The ribbon will slide out easily.

    • With the ribbon unlatched, the entire metal plate should now be detached.

    Agregar Comentario

    • Desolder the marked areas. For desoldering instructions go -here-

    Agregar Comentario

    • Place the spudger underneath the small black tape as shown. Gently lift the spudger up to remove the tape.

    Agregar Comentario

    • Remove the 3.8mm screw from the circuit board.

    • Desolder the marked areas.

    Agregar Comentario

Conclusión

To reassemble your device, follow these instructions in reverse order.

Una persona más ha completado esta guía.

John Bowers

Miembro Desde 18/01/11

841 Reputación

2 Guías creadas

Equipo

Cal Poly, Team 5-17, Amido Winter 2011 Miembro de Cal Poly, Team 5-17, Amido Winter 2011

CPSU-AMIDO-W11S5G17

6 Miembros

7 Guías creadas

Agregar Comentario

Ver Estadísticas:

Ultimas 24 Horas: 0

Últimos 7 Días: 0

Últimos 30 Días: 7

Todo El Tiempo: 3,215