Menú

Tus configuraciones

Mi Mesa de Trabajo

Obtén acceso rápido a guías, partes y respuestas para tus dispositivos
Mi Carrito

Al parecer tu carrito está vacío

Visita Nuestra Tienda

Nikon Coolpix P4 Motherboard Replacement

Escrito Por: Luke Baumann (y 5 de otros participantes)
  • Comentarios: 0
  • Favoritos: 1

Dificultad

Moderar

Pasos

26

Tiempo Requerido

10 minutos

Secciones

3

Banderas

2

Bullets!

Balas!

Mejor coordinación con marcas y color/tipo de balas ayudarán a hacer esta guía más clara!

Markup Mishap

Percance de Marcado

Esta guía necesita mejores marcas. Ayuda corrigiendo o haciendo algunas anotaciones de marcado.

Introducción

This guide will tell you how to replace your motherboard

Herramientas

Comprar estas herramientas

Partes

No se requieren partes.

  1. 'Click' the battery door over to the side.

    • 'Click' the battery door over to the side.

    Traducir

  2. Open the battery door. Inside is the memory card and the battery.

    • Open the battery door. Inside is the memory card and the battery.

    • Click over the orange tab and take out the battery.

    • Close the battery lid by pushing it down and sliding it back.

    Traducir

  3. Remove the four screws located on bottom of camera. (.086in screws)

    • Remove the four screws located on bottom of camera. (.086in screws)

    Traducir

  4. Remove the two screws, then remove the panel. (.113in screws) Remove the two screws, then remove the panel. (.113in screws)

    • Remove the two screws, then remove the panel. (.113in screws)

    Traducir

  5. Remove panel on right side (front view) by removing these two screws. (.196in screws) Remove single screw set underneath panel. (0.083in screw) Remove single screw set underneath panel. (0.083in screw)

    • Remove panel on right side (front view) by removing these two screws. (.196in screws)

    • Remove single screw set underneath panel. (0.083in screw)

    Traducir

  6. Remove the two screws attaching the back panel to the body on the left side. (.188in screws)

    • Remove the two screws attaching the back panel to the body on the left side. (.188in screws)

    Traducir

  7. Gently pull off back cover

    • Gently pull off back cover

    Traducir

  8. Remove the two screws holding on the back panel. Then remove the three screws on the A/V Out tab (left side). (.188in screws) Remove tab.

    • Remove the two screws holding on the back panel. Then remove the three screws on the A/V Out tab (left side). (.188in screws)

    • Remove tab.

    Traducir

  9. Remove the two screws attaching the front panel to the body on the left side. (.18in screws)

    • Remove the two screws attaching the front panel to the body on the left side. (.18in screws)

    Traducir

  10. ¡Envío gratuito para todos los pedidos de más de USD100.00 o que contengan un Pro Tech Toolkit!

    Visita Nuestra Tienda

    ¿Alguna vez arreglaste algo? Eso es genial.

    Comparte tu historia de reparación con #SoyUnGenio

    Todos somos Genios

    Comparte tu historia de reparación con #SoyUnGenio

  11. Flip up front panel.

    • Flip up front panel.

    • There should be wires still attaching the panel to body. DO NOT TRY TO PULL OFF COMPLETELY

    Traducir

  12. Remove three screws as shown. (Right screw:0.084in, Left screw:0.088in, Middle screw:0.114in)

    • Remove three screws as shown. (Right screw:0.084in, Left screw:0.088in, Middle screw:0.114in)

    Traducir

  13. Carefully pull orange LCD connector up and out of the port.

    • Carefully pull orange LCD connector up and out of the port.

    • Be careful to pull vertically while pushing the black tab upwards

    Traducir

  14. Remove the screw below the LCD (.124in)

    • Remove the screw below the LCD (.124in)

    Traducir

  15. Carefully pull out the plug connecting the LCD to the motherboard.

    • Carefully pull out the plug connecting the LCD to the motherboard.

    Traducir

  16. You can now remove the LCD from the camera body.

    • You can now remove the LCD from the camera body.

    • Insert new LCD and reassemble using the steps in reverse order.

    Traducir

  17. Remove the screw to the right of the flash.

    • Remove the screw to the right of the flash.

    • Remove the screw to the right of the microphone on the bottom. (0.124in)

    Traducir

  18. Remove the two screws on the right side of the camera. (0.115 in screws)

    • Remove the two screws on the right side of the camera. (0.115 in screws)

    Traducir

  19. Remove the four bottom screws. (0.116(fat head)-center screw, 0.112(skinny head)-other screws)

    • Remove the four bottom screws. (0.116(fat head)-center screw, 0.112(skinny head)-other screws)

    Traducir

  20. Remove the 7 screws from the back of the camera. (0.111 in screws)

    • Remove the 7 screws from the back of the camera. (0.111 in screws)

    Traducir

  21. Remove the plug that connects the lens to the left side of the motherboard by firmly grasping the base of the plug and pulling gently sideways away from the camera.

    • Remove the plug that connects the lens to the left side of the motherboard by firmly grasping the base of the plug and pulling gently sideways away from the camera.

    Traducir

  22. Remove the right panel.

    • Remove the right panel.

    Traducir

  23. Remove the screw from the top of the camera. (0.112 in screws)

    • Remove the screw from the top of the camera. (0.112 in screws)

    Traducir

  24. Remove the three screws from the motherboard. (0.112 in screws)

    • Remove the three screws from the motherboard. (0.112 in screws)

    • Detach the orange tab with the foam on top. It will click out of place.

    Traducir

  25. Remove the motherboard by pulling it up, out of the port.

    • Remove the motherboard by pulling it up, out of the port.

    Traducir

  26. Carefully remove the tab that connects the flash to the motherboard from the port by gently pulling connector to the right, out of its port.

    • Carefully remove the tab that connects the flash to the motherboard from the port by gently pulling connector to the right, out of its port.

    • Be careful when removing the connector.

    Traducir

  27. Remove the motherboard from camera body.

    • Remove the motherboard from camera body.

    • Replace with a new motherboard and follow the steps in reverse order to reassemble.

    Traducir
Conclusión

To reassemble your device, follow these instructions in reverse order.

Autor

con 5 otros colaboradores

Luke Baumann

Miembro Desde 13/04/11

121 Reputación

5 Guías creadas

Insignias: 5

+ 2 más insignias

Equipo

Cal Poly, Team 8-5, Regan Spring 2011 Miembro de Cal Poly, Team 8-5, Regan Spring 2011

CPSU-REGAN-S11S8G5

4 Miembros

5 Guías creadas

0 Comentarios

Agregar un comentario
Ver Estadísticas:

Ultimas 24 Horas: 0

Últimos 7 Días: 0

Últimos 30 Días: 1

Todo El Tiempo: 2,231