Remove the screw located near the speaker port using a Phillips 00 screwdriver.
  • Remove the screw located near the speaker port using a Phillips 00 screwdriver.

Agregar Comentario

Turn camera upside down so that the battery compartment is facing you.
  • Turn camera upside down so that the battery compartment is facing you.

  • Remove all four screws from the bottom of the camera with a Phillips 00 screwdriver.

Agregar Comentario

  • Rotate the camera to the opposite side where the A/V outlet is located.

  • Unscrew and remove all four screws with a Phillips 00 screwdriver.

Agregar Comentario

  • Turn the camera so that the Wi-Fi adapter is facing you.

  • Unscrew and remove all four screws with a Phillips 00 screwdriver.

Agregar Comentario

  • Using a plastic opening tool, pry the front casing of the camera.

  • Continue this motion all around the front casing of the camera.

  • Gently pull apart the front casing from the rest of the camera.

Agregar Comentario

  • Using the plastic opening tool pry the back casing of the camera.

Agregar Comentario

  • Orange ribbon is fragile

  • Carefully pull apart the back casing of the camera from the front of the camera without tearing the orange ribbon.

Agregar Comentario

  • Pull down the on the black latch to carefully separate the orange ribbon from the motherboard.

  • Pull apart the orange ribbon and front casing from the rest of the camera.

Agregar Comentario

  • Use plastic opening tool to carefully pry the LCD Screen from the camera.

Agregar Comentario

  • Gently pull the ribbon cable down to release the latch, then pull up to remove it from the motherboard.

Agregar Comentario

Agregar Comentario

  • Continue by removing two screws from the back of the camera body.

Agregar Comentario

  • Remove the screw connecting the wifi card cover to the front of the camera.

Agregar Comentario

  • Remove the final screw connecting the Wifi card cover to the case.

Agregar Comentario

  • Gently pull the Wifi card cover off of the camera body.

Agregar Comentario

  • Remove the screw holding the Wifi Card to the camera body.

Agregar Comentario

  • Gently pull the WiFi card out of the camera.

Agregar Comentario

  • Continue removing screws from the outside of the camera body.

  • Next pull the plastic side panel off of the camera body.

  • Be extremely careful when holding the camera around the flash capacitor (circled in green), it is probably still charged, and it is very painful if you are shocked by it.

Agregar Comentario

  • Remove the two screws connecting the strap loop to the camera body.

  • Remove the three screws from the left side of the camera body.

  • Remove the screw by the shutter button.

Agregar Comentario

  • Remove screws from plastic side cover.

  • Pull off plastic cover.

Agregar Comentario

  • Carefully remove the back housing body from the camera.

Agregar Comentario

  • Remove the five screws connecting motherboard to the camera body.

  • Carefully detach the two ribbon cables from the motherboard by releasing the black plastic catch, then pull the cables gently upwards out of the connector.

Agregar Comentario

  • Carefully de-solder the four connections to the motherboard.

Agregar Comentario

Conclusión

To reassemble your device, follow these instructions in reverse order.

Joshua Avery

Miembro Desde 23/01/12

7 Reputación

3 Guías creadas

Equipo

Cal Poly, Team 3-28, Amido Winter 2012 Miembro de Cal Poly, Team 3-28, Amido Winter 2012

CPSU-AMIDO-W12S3G28

4 Miembros

5 Guías creadas

Agregar Comentario

Ver Estadísticas:

Ultimas 24 Horas: 0

Últimos 7 Días: 2

Últimos 30 Días: 14

Todo El Tiempo: 1,173