Saltar al contenido principal

Introducción

Use this guide to replace the battery in the Nexus 4's battery or to disconnect the battery before accessing the internal components. This short repair will only take a few minutes.

    • Remove the SIM tray using the SIM Card Eject Tool.

    • This step is required in order to remove the back case.

  1. Kits de reparación de iPhone X

    ¿Garantía vencida? No te preocupes, tenemos la solución.

    Comprar Ahora

    Kits de reparación de iPhone X

    ¿Garantía vencida? No te preocupes, tenemos la solución.

    Comprar Ahora
  2. Gently open the back case by prying along the edge of the cover, starting at a corner of the phone and circling around the phone using a plastic opening tool. The opening process may take a few minutes. The plastic will make a light snapping noise as the back cover separates from the rest of the phone. The opening process may take a few minutes. The plastic will make a light snapping noise as the back cover separates from the rest of the phone.
    • Gently open the back case by prying along the edge of the cover, starting at a corner of the phone and circling around the phone using a plastic opening tool.

    • The opening process may take a few minutes. The plastic will make a light snapping noise as the back cover separates from the rest of the phone.

  3. Remove the two 1.8 mm Phillips screws holding down the battery connector. Using a plastic opening tool, disconnect the battery cable from its socket on the motherboard.
    • Remove the two 1.8 mm Phillips screws holding down the battery connector.

    • Using a plastic opening tool, disconnect the battery cable from its socket on the motherboard.

    • Remove the blue tape that secures the white antenna cable to the battery.

    • Using a spudger, carefully disconnect the white antenna cable.

    • Carefully pry the battery out with a Plastic Opening Tool, starting at the top left-hand corner and working down towards the bottom right-hand corner.

    • If necessary, you can also use a plastic card to separate the battery from the metal midframe.

    • The battery is securely glued to the phone. When reinstalling the battery, press the battery firmly against the adhesive strip.

Conclusión

To reassemble your device, follow these instructions in reverse order. Start by seating the top of the back to the phone, then gently snap the back in place working from the top to the bottom.

149 personas más completaron esta guía.

Kaitlyn Jones

Miembro Desde 27/01/13

4,892 Reputación

8 Guías creadas

Equipo

Cal Poly, Team 3-32, Amido Winter 2013 Miembro de Cal Poly, Team 3-32, Amido Winter 2013

CPSU-AMIDO-W13S3G32

4 Miembros

8 Guías creadas

I have made some arrangement to clarify particularly using pictures from the teardown that are just perfect. The original picture was not detailed and did not show the battery in place.

Gaetan - Contestar

If you can't power on after battery replace:

Charge for an hour

Try holding down power plus volume down while plugging in power

If that doesn't work replug inside battery connector (this fixed for me)

Recommend data backup before in case you can't get it booting.

Chris Harrow - Contestar

Just did this - thanks for all the instructions, easy if you have the right tools

raymondw999 - Contestar

followed these instructions and the device boots up OK but then immediately shuts down. getting into recovery mode and checking the logs I can see that the phone thinks the battery is over temperature (790C vs max of 68C). Hopefully it's just a poor connection where I fitted it. I'll take it apart and try again later.

keith.griffiths - Contestar

Note that it is very easy to break a screw holding the battery connector - don't over tighten. I've managed to hold down the end of the connector, towards the center of the phone, with a washer fitted to a nearby screw. It's been working fine for 6 months

Rodney - Contestar

Agregar Comentario

Ver Estadísticas:

Ultimas 24 Horas: 0

Últimos 7 Días: 26

Últimos 30 Días: 192

Todo El Tiempo: 108,915