Saltar al contenido principal

Repara tus cosas

Derecho a reparar

Partes y herramientas

  1. Using a plastic opening tool, remove the thin plastic cover from back of the tablet by prying up from its small tab. Using a plastic opening tool, remove the thin plastic cover from back of the tablet by prying up from its small tab. Using a plastic opening tool, remove the thin plastic cover from back of the tablet by prying up from its small tab.
    • Using a plastic opening tool, remove the thin plastic cover from back of the tablet by prying up from its small tab.

  2. Remove the five 2mm screws on  the back of the device using a PH00 screwdriver.
    • Remove the five 2mm screws on the back of the device using a PH00 screwdriver.

  3. Pry the device apart by inserting a plastic opening tool in the seam between the plastic backing and display assembly. Use the tool to unclip the plastic tabs in between the backing and the display. Pull the the plastic backing off the display assembly using your hands. Do not do this step with only your hands. You will require a significant amount of force to separate the device.
    • Pry the device apart by inserting a plastic opening tool in the seam between the plastic backing and display assembly. Use the tool to unclip the plastic tabs in between the backing and the display.

    • Pull the the plastic backing off the display assembly using your hands.

    • Do not do this step with only your hands. You will require a significant amount of force to separate the device.

    Be carefull with the power button cable. Don’t insert the plastic tool in this zone

    Jesus Garcia - Contestar

    Some instruction guides also suggest optional use of a suction cup with which to tug on the glass while separating the plastic backing. I found this helpful. Also, if you have a spudger of more rigid plastic, use that one here. My blue spudgers got chewed up pretty badly during this process.

    Jim - Contestar

    I found that the top right (looking at the screen) doesn’t have any corner clips, just a metal antenna (?), so it is easiest to get this corner popped first and then work your way around. The bottom corners have clips which are tough to undo.

    Jeremy R - Contestar

  4. Detach the three connector ribbons passing over the battery using the plastic opening tool. Detach the three connector ribbons passing over the battery using the plastic opening tool. Detach the three connector ribbons passing over the battery using the plastic opening tool.
    • Detach the three connector ribbons passing over the battery using the plastic opening tool.

    The left two connectors flip up from the cable side. The right connector flips up from opposite the cable.

    Glenn Davis - Contestar

    Note that you don’t just pull the ribbons out. There is a clamp on each connector that needs to be prised opened, releasing the ribbon. This was helpful: https://youtu.be/yru4k62qdEU?t=302

    Royston Shufflebotham - Contestar

  5. Remove the twelve 2mm screws around the perimeter of the battery with a PH00 screwdriver.
    • Remove the twelve 2mm screws around the perimeter of the battery with a PH00 screwdriver.

  6. Disconnect the battery by lifting it upward and pulling it away from the connector. Disconnect the battery by lifting it upward and pulling it away from the connector.
    • Disconnect the battery by lifting it upward and pulling it away from the connector.

    When reassembling reconnect the data ribbon cables first, then connect the battery connection last so that you’re not plugging in data lines while powered. Ideally you’d disconnect the battery first but that’s a bit hard with the design so you just have to try to ensure it’s switched off first.

    Andrew Whalan - Contestar

  7. Remove one screw on the logic board with a PH00 screwdriver.
    • Remove one screw on the logic board with a PH00 screwdriver.

  8. Kits de Reparación de Pantalla LCD de iPhone

    La opción de presupuesto, cubierta por nuestra garantía de por vida.

    Compra kits

    Kits de Reparación de Pantalla LCD de iPhone

    Reduce los costos de reparación, no la calidad.

    Compra kits
  9. Disconnect right speaker connector ribbon from logic board. Lift the speaker out by pulling up on its corner. Lift the speaker out by pulling up on its corner.
    • Disconnect right speaker connector ribbon from logic board.

    • Lift the speaker out by pulling up on its corner.

  10. Disconnect connectors around the perimeter of the motherboard. Disconnect connectors around the perimeter of the motherboard. Disconnect connectors around the perimeter of the motherboard.
    • Disconnect connectors around the perimeter of the motherboard.

  11. Remove motherboard by gently pulling upward under its corner. Remove motherboard by gently pulling upward under its corner.
    • Remove motherboard by gently pulling upward under its corner.

  12. Remove the three 2mm screws along the right side of the device using a PH00 screwdriver.
    • Remove the three 2mm screws along the right side of the device using a PH00 screwdriver.

  13. Unseat the small vibrator motor by gently applying upward pressure with a spudger. Unseat the small vibrator motor by gently applying upward pressure with a spudger.
    • Unseat the small vibrator motor by gently applying upward pressure with a spudger.

    Expect some resistance when prying up on the vibration motor. There was some aggressive double sided tape under it and it was stuck pretty firmly.

    Jim - Contestar

  14. Lift the assembly by gently applying upward pressure with the spudger on the assembly. Lift the assembly by gently applying upward pressure with the spudger on the assembly.
    • Lift the assembly by gently applying upward pressure with the spudger on the assembly.

  15. Gently pull battery-audio jack-USB assembly upward, detaching it from its adhesive. Gently pull battery-audio jack-USB assembly upward, detaching it from its adhesive.
    • Gently pull battery-audio jack-USB assembly upward, detaching it from its adhesive.

  16. Detach LCD connector ribbon by pressing upward on connector latch using a plastic opening tool. Detach LCD connector ribbon by pressing upward on connector latch using a plastic opening tool.
    • Detach LCD connector ribbon by pressing upward on connector latch using a plastic opening tool.

  17. Unscrew the two 2mm Phillips #00 screws holding the ribbon in place. Remove the board by tilting it forward and pulling outward.
    • Unscrew the two 2mm Phillips #00 screws holding the ribbon in place.

    • Remove the board by tilting it forward and pulling outward.

  18. Remove second speaker by gently tilting and pulling upward.
    • Remove second speaker by gently tilting and pulling upward.

  19. Unscrew the two 2mm screws securing the micro HDMI connector with a #PH00 screwdriver. Remove the connector by liberally applying upward pressure. Remove the connector by liberally applying upward pressure.
    • Unscrew the two 2mm screws securing the micro HDMI connector with a #PH00 screwdriver.

    • Remove the connector by liberally applying upward pressure.

  20. Unscrew the 2mm Phillips #00 screw that holds the flash enclosure. Remove the flash assembly with a  plastic opening tool by lifting the assembly upward. Remove the flash assembly with a  plastic opening tool by lifting the assembly upward.
    • Unscrew the 2mm Phillips #00 screw that holds the flash enclosure.

    • Remove the flash assembly with a plastic opening tool by lifting the assembly upward.

    Where can I buy Nexus 10 front glass, pls recommend.

    sandesh30715 - Contestar

Conclusión

To reassemble your device, follow these instructions in reverse order.

5 personas más completaron esta guía.

Benjamin Troller

Miembro Desde 11/04/16

1,872 Reputación

5 Guías creadas

Equipo

Cal Poly, Team 34-18, Maness Spring 2016 Miembro de Cal Poly, Team 34-18, Maness Spring 2016

CPSU-MANESS-S16S34G18

4 Miembros

5 Guías creadas

I’m waiting for the instructions regarding how to remove the old screen and insert the new - it seems to be missing

John Walker - Contestar

It seems you just have to buy a replacement for that whole front housing, including the screen assembly

Oliver Nichol -

Agregar Comentario

Ver Estadísticas:

Ultimas 24 horas: 2

Ultimos 7 días: 7

Ultimos 30 días: 53

Todo El Tiempo: 6,555