Repara tus cosas Comunidad Tienda

NexiGo NS32 Trigger Assembly Replacement

Introducción

This is a guide on how to replace the trigger buttons from inside the NexiGo NS32. There are 10 specific steps in this guide that describe how to take the trigger buttons out of the controller. Be careful not to damage any of the internal components.

Qué necesitas

  1. NexiGo NS32 Trigger Assembly Replacement, Rear Case: paso 1, imagen 1 de 1

    • Orient the controller so that it is face down.

    Editar

  2. NexiGo NS32 Trigger Assembly Replacement: paso 2, imagen 1 de 2 NexiGo NS32 Trigger Assembly Replacement: paso 2, imagen 2 de 2

    • Remove the eight 9 mm Phillips screws that secure the rear case.

    Editar

  3. NexiGo NS32 Trigger Assembly Replacement: paso 3, imagen 1 de 1

    • Lift the rear case up and off.

    • You may need to use an opening tool to help release the rear case, but avoid using excessive force so you don't damage the controller.

    Editar

  4. NexiGo NS32 Trigger Assembly Replacement, Battery: paso 4, imagen 1 de 2 NexiGo NS32 Trigger Assembly Replacement, Battery: paso 4, imagen 2 de 2

    • Grip the white battery connector and pull it directly out of its motherboard socket.

    • This may require some force, as the connectors are secured with a bit of adhesive. If you're having trouble with disconnection, apply some high-concentration isopropyl alcohol to the adhesive to loosen it.

    • Do not pull on the wires.

    Editar

  6. NexiGo NS32 Trigger Assembly Replacement: paso 5, imagen 1 de 3 NexiGo NS32 Trigger Assembly Replacement: paso 5, imagen 2 de 3 NexiGo NS32 Trigger Assembly Replacement: paso 5, imagen 3 de 3

    • Lift the battery up and out.

    • Take care not to bend or puncture the battery as you remove it.

    Editar

  7. NexiGo NS32 Trigger Assembly Replacement, Joystick PCB: paso 6, imagen 1 de 2 NexiGo NS32 Trigger Assembly Replacement, Joystick PCB: paso 6, imagen 2 de 2

    • Remove the three 9 mm Phillips screws that secure the joystick PCB.

    Editar

  8. NexiGo NS32 Trigger Assembly Replacement: paso 7, imagen 1 de 2 NexiGo NS32 Trigger Assembly Replacement: paso 7, imagen 2 de 2

    • Flip up the black ZIF connector locking flap on the left side of the joystick PCB.

    • Pull the ribbon cable directly out of its socket.

    Editar

  9. NexiGo NS32 Trigger Assembly Replacement: paso 8, imagen 1 de 3 NexiGo NS32 Trigger Assembly Replacement: paso 8, imagen 2 de 3 NexiGo NS32 Trigger Assembly Replacement: paso 8, imagen 3 de 3

    • Lift out the joystick PCB.

    Editar

  10. NexiGo NS32 Trigger Assembly Replacement, Trigger Assembly: paso 9, imagen 1 de 1

    • Flip up the black ZIF locking flap that secures the trigger assembly ribbon cable.

    • Disconnect the ribbon cable.

    Editar

  11. NexiGo NS32 Trigger Assembly Replacement: paso 10, imagen 1 de 2 NexiGo NS32 Trigger Assembly Replacement: paso 10, imagen 2 de 2

    • Gently lift out the trigger assembly.

    Editar
Conclusión

To reassemble your device, follow these instructions in reverse order.

Autor

con 2 otros colaboradores

Gage_Atx

Miembro Desde 01/29/24

85 Reputación

1 Guía escrita

Insignias: 3

Equipo

Austin Community College, Team 18-3, Watkins Spring 2024 Miembro de Austin Community College, Team 18-3, Watkins Spring 2024

AUSTINCC-WATKINS-S24S18G3

4 Miembros

6 Guías creadas

0 comentarios

Agregar Comentario

Ver Estadísticas:

Ultimas 24 horas: 1

Ultimos 7 días: 2

Ultimos 30 días: 10

Todo El Tiempo: 93