Repara tus cosas Comunidad Tienda

Nerf Recon CS-6 Plunger Replacement

Introducción

The plunger works with the main spring to launch the dart. The o-ring creates a tight seal to stop air from leaking out when the main spring is compressed. This allows for a more powerful shot.

Qué necesitas

  1. Nerf Recon CS-6 Plunger Replacement, Remove Magazine: paso 1, imagen 1 de 1

    • Skip this step if magazine is already removed.

    • Pull slide back.

    • Pull backwards on release buttons and slide magazine out.

    • Push slide back forward and pull trigger.

    Editar

    My priming bar is stuck how do I fix this?

    Ethan - Contestar

  2. Nerf Recon CS-6 Plunger Replacement, Remove Visible Screws: paso 2, imagen 1 de 1

    • Use the Phillips #0 Screwdriver to remove these 9 screws.

    • All screws marked in red are 9.6 mm Phillips #0 screws.

    • Note that left most screw is longer than the rest and is a 18.6 mm Phillips #0 screw.

    Editar

  3. Nerf Recon CS-6 Plunger Replacement, Remove Hidden Screws: paso 3, imagen 1 de 2 Nerf Recon CS-6 Plunger Replacement, Remove Hidden Screws: paso 3, imagen 2 de 2

    • Pull slide back to reveal more screws.

    • Remove these 2 screws.

    • Push slide forward.

    • Pull trigger to release compression of the main spring.

    • Screws are 9.6 mm Phillips #0.

    • Pulling the trigger will keep spring from launching out of the gun when the two halves are separated.

    Editar

    Lost the trigger spring. What spec of spring can I replace it with?

    derekpearcy - Contestar

  4. Nerf Recon CS-6 Plunger Replacement, Remove Plunger Cap: paso 4, imagen 1 de 1

    • Remove the screws on the plunger cap.

    • Tug the plunger cap off.

    • Screws are 9.6 mm Phillips #0.

    Editar

  6. Nerf Recon CS-6 Plunger Replacement, Remove Slide Screws: paso 5, imagen 1 de 1

    • Remove the 2 screws on the slide.

    • Screws are 9.6 mm Phillips #0.

    • Hold the two halves of the gun together to prevent any springs from launching out.

    Editar

  7. Nerf Recon CS-6 Plunger Replacement, Split the Gun in Half: paso 6, imagen 1 de 2 Nerf Recon CS-6 Plunger Replacement, Split the Gun in Half: paso 6, imagen 2 de 2

    • Pull the gun apart at the middle seam.

    • Watch for any springs that might launch out.

    Editar

    Pay attention to the orientation of the tabs on the compression tube. The tabs fit into grooves on the side of the gun. This tripped me up.

    Bob - Contestar

  8. Nerf Recon CS-6 Plunger Replacement, Remove Spring: paso 7, imagen 1 de 2 Nerf Recon CS-6 Plunger Replacement, Remove Spring: paso 7, imagen 2 de 2

    • Pull the spring out the back of the gun.

    Editar

  9. Nerf Recon CS-6 Plunger Replacement, Removing Plunger Guide: paso 8, imagen 1 de 1

    • Lift the plunger guide straight up out of the gun.

    Editar

  10. Nerf Recon CS-6 Plunger Replacement, Remove Plunger: paso 9, imagen 1 de 1

    • Pull the plunger out the back of the gun off of the inner piece.

    Editar

  11. Nerf Recon CS-6 Plunger Replacement, Remove Other Half of Plunger: paso 10, imagen 1 de 1

    • Pull the remaining half of the plunger out the back of the gun.

    Editar

    Hi, do you know where is the place that I can purchase the plunger?

    mohd-fairuz - Contestar

Conclusión

To reassemble your device, follow these instructions in reverse order.

2 personas más completaron esta guía.

Autor

con 3 otros colaboradores

Asad Qureshi

Miembro Desde 10/22/14

586 Reputación

3 Guías creadas

Insignias: 17

+ 14 más insignias

Equipo

Baylor, Team 8-14, Williams Fall 2014 Miembro de Baylor, Team 8-14, Williams Fall 2014

BU-WILLIAMS-F14S8G14

3 Miembros

6 Guías creadas

Un comentario

Do you know anywhere that you can buy a replacement plunger? Thanks

Angela Hirschi - Contestar

Agregar Comentario

Ver Estadísticas:

Ultimas 24 horas: 1

Ultimos 7 días: 5

Ultimos 30 días: 15

Todo El Tiempo: 4,651