Introducción

Use this guide to remove the circuit board that activates the automatic firing mechanism.

Partes

No se requieren partes.

  1. Before disassembling your Nerf Hail-Fire, be sure to remove the batteries.
    • Before disassembling your Nerf Hail-Fire, be sure to remove the batteries.

    • Remove the two 9.0 mm Phillips screws securing the battery compartment.

    • Slide the battery compartment out.

    Agregar Comentario

  2. Remove the five 9.0 mm Phillips screws securing the trigger.
    • Remove the five 9.0 mm Phillips screws securing the trigger.

    Agregar Comentario

    • Remove the single 11.0 mm Phillips screw securing the magazine cartridge chambers.

    • Pull the entire chamber upwards to separate it from the rest of the Nerf Gun.

    Agregar Comentario

    • Remove both halves of the ring by tugging on it upwards until the lock gets freed.

    • This requires quite a bit of force and if you are not careful, you may break the plastic lock.

    Agregar Comentario

    • Remove the four 9.0 mm Phillips screws from the newly revealed cylinder.

    Agregar Comentario

    • Remove the three 9.0 mm Phillips screws holding the top latch of the Nerf Gun together.

    Agregar Comentario

    • Remove the three 9.0 mm Phillips screws holding together the firing chamber.

    • Remove the single 7.0 mm Phillips screw below the barrel.

    • Remove the two 14.0 mm Philips screws using a screwdriver with a length of approximately 4.0 inches and a diameter of approximately 0.2 cm.

    Agregar Comentario

    • Remove the single 14.0 mm Phillips screw holding together the handle and the Nerf Gun.

    Agregar Comentario

  3. Reparte el espíritu de reparación esta Navidad
    Obtén $12 de descuento en tu compra de $50 o más con el código FIXMAS12
    Reparte el espíritu de reparación esta Navidad
    Obtén $12 de descuento en tu compra de $50 o más con el código FIXMAS12
    • Remove the two 9.0 mm Phillips screws holding together the handle.

    • Remove the plastic cover of the handle.

    Agregar Comentario

    • Insert one plastic opening tool inside one side of the orange part depicted in the picture.

    • Insert a second plastic opening tool to the other side of the orange part and gradually pull the piece out, freeing it from the handle.

    Agregar Comentario

    • Pull one end of the handle away from the orange latch.

    • Repeat the procedure on the other side to completely remove the handle from the rest of the Nerf Gun.

    Agregar Comentario

    • Lift the entire left shell slowly. The process should be easy and if there is any resistance, there is something wrong. You may have forgotten a screw.

    • Completely remove the left shell from the rest of the Nerf Gun.

    Agregar Comentario

    • Remove the cartridge support.

    Agregar Comentario

    • Remove the handle crank.

    Agregar Comentario

    • Remove the clear plastic barrel cover.

    Agregar Comentario

    • Remove the firing pin.

    Agregar Comentario

    • Lift the trigger mechanism out of the shell.

    • You cannot fully remove the trigger mechanism just yet. However taking it out of the shell helps in later steps.

    Agregar Comentario

    • Remove the two 9.0 mm Phillips screws.

    Agregar Comentario

    • To remove the motor and trigger mechanism you have to detach these two wires which are glued to the shell.

    • Hold close to the wire and pull upward slowly.

    • If you pull too quickly you can potentially damage the wire.

    Agregar Comentario

    • Once all the pieces are removed the right shell should be fully accessible.

    Agregar Comentario

    • Once you have the handle disassembled locate the triggering circuit board.

    Agregar Comentario

    • Find the two plastic clasps and position your hands so you can pry them open with your fingers. We recommend that you try and pry them open without removing the piece so you can feel how fragile the plastic is.

    Agregar Comentario

    • The circuit board has sharp metal solder points on it. If your finger slips you could injure yourself. Consider using gloves.

    • To remove use two fingers to pry the plastic edges apart and with your thumbs remove the circuit board. Having a friend help with this step could be beneficial.

    Agregar Comentario

Conclusión

To reassemble your device, follow these instructions in reverse order.

Una persona más ha completado esta guía.

sage

Miembro Desde 24/01/14

301 Reputación

3 Guías creadas

Equipo

Cal Poly, Team 13-13, Regan Winter 2014 Miembro de Cal Poly, Team 13-13, Regan Winter 2014

CPSU-REGAN-W14S13G13

4 Miembros

7 Guías creadas

Agregar Comentario

Ver Estadísticas:

Ultimas 24 Horas: 1

Últimos 7 Días: 1

Últimos 30 Días: 7

Todo El Tiempo: 797