Saltar al contenido principal

Introducción

This will show you how to replace your camera.

Partes

No se especificaron partes.

  1. Using your finger, press down on the clip holding the back cover on.
    • Using your finger, press down on the clip holding the back cover on.

  2. Using the spudger or your finger, gently pull the battery out from the top.
    • Using the spudger or your finger, gently pull the battery out from the top.

  3. Remove the four rubber pieces from the face of the phone using the sharp end of the spudger.
    • Remove the four rubber pieces from the face of the phone using the sharp end of the spudger.

    • The rubber pieces are held in with a mild adhesive.

  4. Remove the four Torx-6 screws from underneath the rubber pieces.
    • Remove the four Torx-6 screws from underneath the rubber pieces.

  5. Kits de reparación de iPhone X

    ¿Garantía vencida? No te preocupes, tenemos la solución.

    Comprar Ahora

    Kits de reparación de iPhone X

    ¿Garantía vencida? No te preocupes, tenemos la solución.

    Comprar Ahora
  6. Close the phone before proceeding. Using the flat end of the spudger, insert it under the plastic at the top left of the phone.
    • Close the phone before proceeding.

    • Using the flat end of the spudger, insert it under the plastic at the top left of the phone.

    • Gently, although a small amount of force is required, use a twisting motion to pull the plastic casing away from the body of the phone.

    • Continue to move around the phone counter clockwise until the casing is separated from the body.

    • It is not unusual for it to pop off before making it back to the starting point.

  7. If the casing has not popped off of the body, remove it carefully from the the phone.
    • If the casing has not popped off of the body, remove it carefully from the the phone.

  8. After completing Steps 3-6 in the casing repair guide, your phone should look like this.
    • After completing Steps 3-6 in the casing repair guide, your phone should look like this.

  9. Use the spudger to unhinge the four clips around the metal casing of the top logic board. Gently take off the metal casing of the logic board. Gently take off the metal casing of the logic board.
    • Use the spudger to unhinge the four clips around the metal casing of the top logic board.

    • Gently take off the metal casing of the logic board.

  10. Use spudger to gently disconnect the ribbon cable from phone. Gently remove Logic Board making sure not to damage any other components. Gently remove Logic Board making sure not to damage any other components.
    • Use spudger to gently disconnect the ribbon cable from phone.

    • Gently remove Logic Board making sure not to damage any other components.

  11. Find the camera on the board.
    • Find the camera on the board.

  12. Take your spudger and place it just under the camera as shown. With a small force, the camera should remove easily.
    • Take your spudger and place it just under the camera as shown.

    • With a small force, the camera should remove easily.

Conclusión

To reassemble your device, follow these instructions in reverse order.

Una persona más ha completado esta guía.

Koedy Brant

Miembro Desde 26/01/10

41 Reputación

2 Guías creadas

Equipo

Cal Poly, Team 8-50, Regan Winter 2010 Miembro de Cal Poly, Team 8-50, Regan Winter 2010

CPSU-REGAN-W10S8G50

3 Miembros

14 Guías creadas

Agregar Comentario

Ver Estadísticas:

Ultimas 24 Horas: 0

Últimos 7 Días: 0

Últimos 30 Días: 0

Todo El Tiempo: 2,051