Repara tus cosas Comunidad Tienda

Esta guía ha sufrido modificaciones. Revisa la última versión sin revisar.

Motorola V180 LCD screen replacement

Introducción

Replacing the screen and connector ribbon.

Qué necesitas

  1. Motorola V180 LCD screen replacement, Connector Ribbon: paso 1, imagen 1 de 1

    • Gently tug on the upper edge of the faceplate, and it will easily detach.

    Traducir

  2. Motorola V180 LCD screen replacement: paso 2, imagen 1 de 1

    • Remove the four screws securing the front cover.

    Traducir

  3. Motorola V180 LCD screen replacement: paso 3, imagen 1 de 1

    • Gently glide the metallic silver cover outward.

    • This piece is wedged in tight. Try to slide out one hook at a time, instead of both simultaneously.

    Traducir

  4. Motorola V180 LCD screen replacement: paso 4, imagen 1 de 1

    • Insert a pair of tweezers between the silver and black sections of the cover.

    • The silver section should now easily snap away.

    Traducir

  5. Motorola V180 LCD screen replacement: paso 5, imagen 1 de 1

    • The black rubber component can now easily be taken off.

    Traducir

  7. Motorola V180 LCD screen replacement: paso 6, imagen 1 de 1

    • Use a soldering iron to detach the connector ribbon from the phone.

    Traducir

  8. Motorola V180 LCD screen replacement, Motherboard: paso 7, imagen 1 de 3 Motorola V180 LCD screen replacement, Motherboard: paso 7, imagen 2 de 3 Motorola V180 LCD screen replacement, Motherboard: paso 7, imagen 3 de 3

    • Use your T6 Torx Screwdriver to unscrew the four screws located on the back of the phone.

    • Remove the SIM card located on the back of the phone.

    • A ribbon near the antenna is still attached to the motherboard. Do not break this ribbon.

    Traducir

  9. Motorola V180 LCD screen replacement: paso 8, imagen 1 de 2 Motorola V180 LCD screen replacement: paso 8, imagen 2 de 2

    • Unclip the pronged rectangle connector ribbon attached to the motherboard.

    • Remove the motherboard by lifting it up out of the keypad.

    Traducir

  10. Motorola V180 LCD screen replacement, Motherboard: paso 9, imagen 1 de 3 Motorola V180 LCD screen replacement, Motherboard: paso 9, imagen 2 de 3 Motorola V180 LCD screen replacement, Motherboard: paso 9, imagen 3 de 3

    • Power off the Motorola V180.

    • Flip the phone over to its back side.

    • Hold down the button and slide off the back cover.

    • Remove the battery.

    Traducir

  11. Motorola V180 LCD screen replacement: paso 10, imagen 1 de 3 Motorola V180 LCD screen replacement: paso 10, imagen 2 de 3 Motorola V180 LCD screen replacement: paso 10, imagen 3 de 3

    • Use your T6 Torx Screwdriver to unscrew the four screws located on the back of the phone.

    • Remove the SIM card located on the back of the phone.

    • A ribbon near the antenna is still attached to the motherboard. Do not break this ribbon.

    Traducir

  12. Motorola V180 LCD screen replacement: paso 11, imagen 1 de 2 Motorola V180 LCD screen replacement: paso 11, imagen 2 de 2

    • Unclip the pronged rectangle connector ribbon attached to the motherboard.

    • Remove the motherboard.

    Traducir

  13. Motorola V180 LCD screen replacement, Screen and Connector Ribbon: paso 12, imagen 1 de 2 Motorola V180 LCD screen replacement, Screen and Connector Ribbon: paso 12, imagen 2 de 2

    • Now that the ribbon is loose, the screen (white part) can swing away.

    • Some of the black "tape" can be peeled back, but the screen is still attached. More work may be required to fully separate this part.

    Traducir

  14. Motorola V180 LCD screen replacement: paso 13, imagen 1 de 2 Motorola V180 LCD screen replacement: paso 13, imagen 2 de 2

    • Slide out the part of the connector ribbon that was just attached to the motherboard through this narrow slot in the phone.

    • This is a tight fit. Be careful to not tear the ribbon while maneuvering it through this slot.

    • The entire connector ribbon unit can now be removed from the phone.

    Traducir
Conclusión

To reassemble your device, follow these instructions in reverse order.

Autor

con 6 otros colaboradores

Tyler Knisley

Miembro Desde 05/07/10

1 Reputación

7 Guías creadas

Insignias: 4

+1 mas insignia

Equipo

Cal Poly, Team 6-16, Maness Spring 2010 Miembro de Cal Poly, Team 6-16, Maness Spring 2010

CPSU-MANESS-S10S6G16

4 Miembros

13 Guías creadas

0 comentarios

Agregar Comentario

Ver Estadísticas:

Ultimas 24 horas: 2

Ultimos 7 días: 6

Ultimos 30 días: 19

Todo El Tiempo: 3,308