Saltar al contenido principal

Motorola Moto G7 Screen Replacement

Qué necesitas

  1. Motorola Moto G7 Screen Replacement, Screen: paso 1, imagen 1 de 3 Motorola Moto G7 Screen Replacement, Screen: paso 1, imagen 2 de 3 Motorola Moto G7 Screen Replacement, Screen: paso 1, imagen 3 de 3
    • Use the iFixit opening tools to gently wedge the front screen from the rest of the device.

    • Try to focus on the corners to make it easier to insert and use the iFixit opening picks.

    • It is also recommended to use the iOpener or a heat gun to weaken the adhesive that holds the edges of the screen down.

    • The screen is glass, so when using force to lift the screen, be cautious of cracked glass and stray shards of glass coming off.

    • You have to be extra careful to dig deep enough, so you lift the entire screen unit!

    I just destroyed my screen by dividing it in two parts. You have to be extra careful to dig deep enough in the first step, so you lift the entire screen unit!

    Michael - Contestar

    Thanks... I almost did just that!

    Carlisle “Mike” Wick - Contestar

  2. Motorola Moto G7 Screen Replacement: paso 2, imagen 1 de 1
    • Excessive glass and adhesive around the edges should be removed with the spudger.

    • The glass is black and may blend in with edges of the device. Be cautious using bare hands when moving the device.

  3. Motorola Moto G7 Screen Replacement: paso 3, imagen 1 de 2 Motorola Moto G7 Screen Replacement: paso 3, imagen 2 de 2
    • Remove three 2.7mm T3 Torx screws from the metal piece to the right of the battery.

  4. Motorola Moto G7 Screen Replacement: paso 4, imagen 1 de 3 Motorola Moto G7 Screen Replacement: paso 4, imagen 2 de 3 Motorola Moto G7 Screen Replacement: paso 4, imagen 3 de 3
    • Use a spudger to gently take off the metal piece that was held down by the screws.

    • A second metal piece is held under the first. This can also be popped off by using the spudger and nudging it under the metal piece connected to the band.

    This would also be a good place to disconnect the battery connector, which is right under the display connector.

    Daniel Kim - Contestar

    At this point, one could remove the battery. I don't see why the remaining steps are necessary.

    Kimball - Contestar

    there is one more piece to remove here. 3 black screws (T3 but longer) and the part visible above the battery on the last image above. Empty space on the top of the image in step 5.

    Tadeusz Liszka - Contestar

Conclusión

To reassemble your device, follow these instructions in reverse order.

16 personas más completaron esta guía.

Peter Nelson

Miembro Desde 01/23/20

742 Reputación

3 Guías creadas

Equipo

Cal Poly, Team S19-G6, White Winter 2020 Miembro de Cal Poly, Team S19-G6, White Winter 2020

CPSU-WHITE-W20S19G6

4 Miembros

20 Guías creadas

3 comentarios

The replacement part listed here on iFixit indicates installation adhesive is not included. Can you reuse the adhesive on the old part? If not, what adhesive is recommended for this type of repair?

Gabe LaBounty - Contestar

You can’t. I used the 1 mil tape and it worked.

Javier Vilalta - Contestar

How much would it cost to send this in for someone else to put in a new screen?

Nathaniel Mcvay - Contestar

Agregar Comentario

Ver Estadísticas:

Ultimas 24 horas: 10

Ultimos 7 días: 30

Ultimos 30 días: 123

Todo El Tiempo: 11,656