Menú

Tus configuraciones

Mi Mesa de Trabajo

Obtén acceso rápido a guías, partes y respuestas para tus dispositivos
Mi Carrito

Al parecer tu carrito está vacío

Visita Nuestra Tienda

Motorola Moto G4 Play Charging Port Replacement

Escrito Por: Francisco Hernández (y otro participante)
  • Comentarios: 1
  • Favoritos: 1
  • Terminaciones: 3

Dificultad

Moderar

Pasos

12

Tiempo Requerido

20 - 25 minutos

Secciones

3

Banderas

1

Better Introduction

Mejor introducción

Mejora esta guía completando o revisando su introducción.

Introducción

Use this guide to replace the charging port on the Motorola Moto G4 Play.

Herramientas

Comprar estas herramientas

Partes

No se especificaron partes.

  1. Open case with a plastic opening tool that has the same size as the divot located at the bottom left of the phone. If you don’t have an opening tool, use your finger nails. Open case with a plastic opening tool that has the same size as the divot located at the bottom left of the phone. If you don’t have an opening tool, use your finger nails. Open case with a plastic opening tool that has the same size as the divot located at the bottom left of the phone. If you don’t have an opening tool, use your finger nails.

    • Open case with a plastic opening tool that has the same size as the divot located at the bottom left of the phone. If you don’t have an opening tool, use your finger nails.

    Traducir

  2. Lift the case by the nearest corner to the divot and remove it from the phone. Lift the case by the nearest corner to the divot and remove it from the phone. Lift the case by the nearest corner to the divot and remove it from the phone.

    • Lift the case by the nearest corner to the divot and remove it from the phone.

    Traducir

  3. Place the plastic opening tool into the notch located at the bottom of the battery compartment, and lift upwards. If you don’t have an opening tool, use your finger nails. Remove battery from your phone. Remove battery from your phone.

    • Place the plastic opening tool into the notch located at the bottom of the battery compartment, and lift upwards. If you don’t have an opening tool, use your finger nails.

    • Remove battery from your phone.

    Traducir

  4. Remove any SIM card and/or memory card present using your hand. Remove any SIM card and/or memory card present using your hand. Remove any SIM card and/or memory card present using your hand.

    • Remove any SIM card and/or memory card present using your hand.

    Traducir

  5. Kits de Reparación de Batería de MacBook Air

    A partir de $69.99

    Buy Now

    Kits de Reparación de Batería de MacBook Air

    A partir de $69.99

    Buy Now

  6. Remove the small silicon cover at the bottom right of the camera using tweezers. Remove the small silicon cover at the bottom right of the camera using tweezers.

    • Remove the small silicon cover at the bottom right of the camera using tweezers.

    Traducir

  7. Remove the sixteen (16) 3mm Phillips PH000 screws securing the midframe.

    • Remove the sixteen (16) 3mm Phillips PH000 screws securing the midframe.

    • Some phones have two shorter screws, one on each side of the battery (double marked with orange circles at left). If your device has these shorter screws, make sure they go back in their original holes.

    Traducir

  8. Remove the back panel assembly with your hands. Remove the back panel assembly with your hands. Remove the back panel assembly with your hands.

    • Remove the back panel assembly with your hands.

    Traducir

  9. Use tweezers to pop up the antenna wire. Use tweezers to pop up the antenna wire.

    • Use tweezers to pop up the antenna wire.

    Traducir

  10. Use the flat end of a spudger to pry up on the connector at the bottom of the battery space. Use the flat end of a spudger to pry up on the connector at the bottom of the battery space.

    • Use the flat end of a spudger to pry up on the connector at the bottom of the battery space.

    Traducir

  11. Remove the two (2) 3mm Phillips PH000 screws securing the charging port.

    • Remove the two (2) 3mm Phillips PH000 screws securing the charging port.

    Traducir

  12. Insert the tweezers under the vibrator and gently lift up the whole part. Insert the tweezers under the vibrator and gently lift up the whole part. Insert the tweezers under the vibrator and gently lift up the whole part.

    • Insert the tweezers under the vibrator and gently lift up the whole part.

    Traducir

  13. Pop up on the vibrator's connector to separate it from the charging port. Pop up on the vibrator's connector to separate it from the charging port. Pop up on the vibrator's connector to separate it from the charging port.

    • Pop up on the vibrator's connector to separate it from the charging port.

    Traducir
Conclusión

To reassemble your device, follow these instructions in reverse order.

3 personas más completaron esta guía.

Autor

con 1 otro colaborador

Francisco Hernández

Miembro Desde 15/02/18

378 Reputación

2 Guías creadas

Insignias: 7

+ 4 más insignias

Equipo

USF Tampa, Team S17-G4, Boczar Spring 2018 Miembro de USF Tampa, Team S17-G4, Boczar Spring 2018

USFT-BOCZAR-S18S17G4

4 Miembros

6 Guías creadas

0 Comentarios

Agregar un comentario

Agregar Comentario

Ver Estadísticas:

Ultimas 24 Horas: 6

Últimos 7 Días: 27

Últimos 30 Días: 125

Todo El Tiempo: 1,370