Repara tus cosas Comunidad Tienda

Moto Z Display Assembly Replacement

Sólo Prerrequisito
Esta guía solo debería usarse como prerrequisito para otras guías. Por tanto, estará incompleta.

Introducción

Prereq to open the phone and remove the screen.

Qué necesitas

  1. Moto Z Display Assembly Replacement, Display Assembly: paso 1, imagen 1 de 1

    • Heat an iOpener and apply it to the left edge of the phone for at least 90 seconds.

    • A hair dryer, heat gun, or hot plate may also be used, but be careful not to overheat the phone—the OLED display and internal battery are both susceptible to heat damage.

    • As you're waiting for the adhesive to soften, move on and read the following step to get an idea of where to pry.

    Traducir

  2. Moto Z Display Assembly Replacement: paso 2, imagen 1 de 2 Moto Z Display Assembly Replacement: paso 2, imagen 2 de 2

    • In the following steps you will be cutting through the adhesive around the edge of the display assembly.

    • To avoid damage, do not cut in the following areas:

    • The OLED panel

    • The home button

    • The flash unit

    Traducir

  3. Moto Z Display Assembly Replacement: paso 3, imagen 1 de 3 Moto Z Display Assembly Replacement: paso 3, imagen 2 de 3 Moto Z Display Assembly Replacement: paso 3, imagen 3 de 3

    • Apply a suction cup as close to the heated edge as possible.

    • Lift on the suction cup and insert the tip of an opening pick into the gap.

    • Do not insert the pick more than 1/16" (1.5 mm). Over-inserting the pick may damage the OLED panel.

    Traducir

  4. Moto Z Display Assembly Replacement: paso 4, imagen 1 de 3 Moto Z Display Assembly Replacement: paso 4, imagen 2 de 3 Moto Z Display Assembly Replacement: paso 4, imagen 3 de 3

    • Carefully slide the tip of the opening pick down and up the side of the phone, making sure not to cut deeper than 1/16" (1.5 mm).

    • As you run the pick along the side, you will feel the tip of the pick press against the edge of the OLED panel. That is as far as the pick should go without damaging the panel.

    • Once you have separated the adhesive, leave an opening pick in the side to keep the adhesive from resealing.

    Traducir

  5. Moto Z Display Assembly Replacement: paso 5, imagen 1 de 1

    • Repeat the heating, lifting, and cutting steps for the remaining long edge of the phone.

    Traducir

  7. Moto Z Display Assembly Replacement: paso 6, imagen 1 de 1
    Traducir

  8. Moto Z Display Assembly Replacement: paso 7, imagen 1 de 2 Moto Z Display Assembly Replacement: paso 7, imagen 2 de 2

    • Insert an opening pick into the flash side corner of the phone and carefully slice around the flash unit.

    • Do not insert the pick more than 1/16" (1.5 mm) into the edge.

    • Once you are done cutting, leave the pick in the corner to prevent the adhesive from resealing.

    Traducir

  9. Moto Z Display Assembly Replacement: paso 8, imagen 1 de 3 Moto Z Display Assembly Replacement: paso 8, imagen 2 de 3 Moto Z Display Assembly Replacement: paso 8, imagen 3 de 3

    • Insert an opening pick into the remaining top corner of the phone.

    • Carefully slice through the adhesive across the top of the phone.

    • Do not insert the pick beyond 1/2" (12.5 mm).

    Traducir

  10. Moto Z Display Assembly Replacement: paso 9, imagen 1 de 1

    • Apply a heated iOpener to the bottom edge of the phone for at least 90 seconds.

    Traducir

  11. Moto Z Display Assembly Replacement: paso 10, imagen 1 de 3 Moto Z Display Assembly Replacement: paso 10, imagen 2 de 3 Moto Z Display Assembly Replacement: paso 10, imagen 3 de 3

    • Insert an opening pick into a bottom corner and slice towards the home button, stopping before you reach it.

    • Once you're done with the corner, leave a pick in place to prevent the adhesive from sealing.

    • Repeat the process for the other bottom corner.

    Traducir

  12. Moto Z Display Assembly Replacement: paso 11, imagen 1 de 2 Moto Z Display Assembly Replacement: paso 11, imagen 2 de 2

    • Carefully twist the first opening pick slightly to help release the edge adhesive.

    • Repeat the same process for each remaining pick, moving them as necessary and twisting slightly to release the adhesive.

    Traducir

  13. Moto Z Display Assembly Replacement: paso 12, imagen 1 de 3 Moto Z Display Assembly Replacement: paso 12, imagen 2 de 3 Moto Z Display Assembly Replacement: paso 12, imagen 3 de 3

    • Lift the earpiece end of the display up to provide access to the display cables.

    • Do not open the display beyond 90 degrees, and always support the display panel.

    Traducir

  14. Moto Z Display Assembly Replacement: paso 13, imagen 1 de 3 Moto Z Display Assembly Replacement: paso 13, imagen 2 de 3 Moto Z Display Assembly Replacement: paso 13, imagen 3 de 3

    • Use the point of a spudger to pry the display cable shield up.

    • Remove the display cable shield.

    Traducir

  15. Moto Z Display Assembly Replacement: paso 14, imagen 1 de 2 Moto Z Display Assembly Replacement: paso 14, imagen 2 de 2

    • Use the point of the spudger to lift and disconnect the display cable connector from its socket.

    Traducir

  16. Moto Z Display Assembly Replacement: paso 15, imagen 1 de 2 Moto Z Display Assembly Replacement: paso 15, imagen 2 de 2

    • Remove the display assembly.

    • Before you reinstall the display assembly, thoroughly remove any remaining adhesive and glass from the frame.

    • After removing all traces of glue and glass from the frame, clean the adhesion areas with 90% (or higher) isopropyl alcohol and a lint-free cloth or coffee filter.

    • Be sure to turn on your phone and test your repair before installing new adhesive and resealing the phone.

    • Use the Motorola Moto Z display adhesive to reseal your phone.

    Traducir
Linea de Meta

Autor

con 2 otros colaboradores

Arthur Shi

Miembro Desde 01/03/18

249,820 Reputación

503 Guías creadas

Insignias: 47

+ 44 más insignias

Equipo

iFixit Miembro de iFixit

Staff

135 Miembros

16,731 Guías creadas

0 comentarios

Agregar Comentario

Ver Estadísticas:

Ultimas 24 horas: 0

Ultimos 7 días: 0

Ultimos 30 días: 0

Todo El Tiempo: 115