Saltar al contenido principal

Repara tus cosas

Derecho a reparar

Tienda

Introducción

Use this guide to replace the left and right speakers in the Microsoft Surface Pro.

  1. Use a heated iOpener or a heat gun to heat the edges of the display and soften its adhesive.
    • Use a heated iOpener or a heat gun to heat the edges of the display and soften its adhesive.

    • If you're using an iOpener it may take several cycles of reheating and applying it to soften the adhesive enough. Every time, let the iOpener sit on the display for at least a minute before reheating to allow the adhesive to soften.

  2. Apply a suction cup as close as possible to the edge of the display. Use the suction cup to lift the edge of the display enough to insert an opening pick under the edge.
    • Apply a suction cup as close as possible to the edge of the display.

    • Use the suction cup to lift the edge of the display enough to insert an opening pick under the edge.

    • Slide the opening pick all the way around the edges of the display to cut through the adhesive on the bezel.

    • Do not insert the opening pick past the bezel of the display—you may permanently damage the display.

    • Be very careful and move slowly during this step. The display is fragile and will crack if too much force is applied against it. If your tools seem stuck, apply more heat to further soften the adhesive.

  3. Starting from the top edge, lift the display slightly. If you feel any resistance, use heat and an opening pick to slice through any remaining adhesive. Before completely removing the display, disconnect the three display cables.
    • Starting from the top edge, lift the display slightly. If you feel any resistance, use heat and an opening pick to slice through any remaining adhesive.

    • Before completely removing the display, disconnect the three display cables.

  4. Remove the display.
    • Remove the display.

  5. Unscrew all the 23 screws located on the outside panel with the T5 torx screw driver Unscrew all the 23 screws located on the outside panel with the T5 torx screw driver
    • Unscrew all the 23 screws located on the outside panel with the T5 torx screw driver

  6. Use the plastic opening tool to pry out the cameras
    • Use the plastic opening tool to pry out the cameras

  7. Pull the outside panel with your hands from the Surface Pro
    • Pull the outside panel with your hands from the Surface Pro

  8. Use the T5 torx screw driver to unscrew the 6 T5 screws located on the left and right metal panels Use the T2 torx screw driver to unscrew the 23 T2 screws located on the left and right metal panels
    • Use the T5 torx screw driver to unscrew the 6 T5 screws located on the left and right metal panels

    • Use the T2 torx screw driver to unscrew the 23 T2 screws located on the left and right metal panels

  9. Gently pull out left and right metal panels with hands
    • Gently pull out left and right metal panels with hands

  10. Disconnect the two speakers with tweezers Gently pry out the speakers with spudger
    • Disconnect the two speakers with tweezers

    • Gently pry out the speakers with spudger

Conclusión

To reassemble your device, follow these instructions in reverse order.

Una persona más ha completado esta guía.

Jonathan Choi

Miembro Desde 09/10/13

792 Reputación

4 Guías creadas

Equipo

Cal Poly, Team 8-20, Regan Fall 2013 Miembro de Cal Poly, Team 8-20, Regan Fall 2013

CPSU-REGAN-F13S8G20

4 Miembros

11 Guías creadas

Agregar Comentario

Ver Estadísticas:

Ultimas 24 horas: 0

Ultimos 7 días: 5

Ultimos 30 días: 21

Todo El Tiempo: 2,475