Saltar al contenido principal

Esta guía ha sufrido modificaciones. Revisa la última versión sin revisar.

Microsoft Surface Book Screen Replacement

Qué necesitas

  1. Microsoft Surface Book Screen Replacement, Screen: paso 1, imagen 1 de 3 Microsoft Surface Book Screen Replacement, Screen: paso 1, imagen 2 de 3 Microsoft Surface Book Screen Replacement, Screen: paso 1, imagen 3 de 3
    Herramienta utilizada en este paso:
    iSclack
    $24.99
    Comprar
    • Turn off your Surface Book and detach the display.

    • Heat and apply an iOpener or use a hair dryer or heat gun to heat the perimeter of the display, in order to soften the glue securing it.

    • Use a suction cup or iSclack or pull up on the edge of the display, and create a slight gap between the display glass and the frame.

    • Insert an opening pick into the gap.

    • Use only gentle force with the pick, and keep the display very hot (slightly too hot to touch). If you use too much force and/or allow the glue to harden, the glass will crack.

  2. Microsoft Surface Book Screen Replacement: paso 2, imagen 1 de 2 Microsoft Surface Book Screen Replacement: paso 2, imagen 2 de 2
    • Use the pick to slice all the way around the perimeter of the display to separate the glue.

    • Do not insert the opening pick too far into the display or you may cause damage to internal components.

    • Gently raise the display but don't fully detach it until the cables underneath are disconnected.

  3. Microsoft Surface Book Screen Replacement: paso 3, imagen 1 de 3 Microsoft Surface Book Screen Replacement: paso 3, imagen 2 de 3 Microsoft Surface Book Screen Replacement: paso 3, imagen 3 de 3
    • The ribbons are circled. Begin by removing the ribbon on the right (in red). With the curved tweezers, carefully remove the metal bracket to expose the end of the ribbon. Remove ribbon.

  4. Microsoft Surface Book Screen Replacement: paso 4, imagen 1 de 3 Microsoft Surface Book Screen Replacement: paso 4, imagen 2 de 3 Microsoft Surface Book Screen Replacement: paso 4, imagen 3 de 3
    • Next, remove the metal shield covering the other ribbon. Then remove the ribbon.

Conclusión

To reassemble your device, follow these instructions in reverse order.

25 personas más completaron esta guía.

Wesley Kendrick

Miembro Desde 02/15/17

2,103 Reputación

2 Guías creadas

Equipo

USF Tampa, Team 1-6, Sullivan Spring 2017 Miembro de USF Tampa, Team 1-6, Sullivan Spring 2017

USFT-SULLIVAN-S17S1G6

3 Miembros

14 Guías creadas

30 comentarios

It is very unlikely you will get this screen off without breaking it. Luckily, my customer only wanted the SSD out of the device so he didn't care if I damaged it. This screen is crazy fragile and the glue is very very strong. Do not do this job thinking you will likely not break the screen, unless you have done it before.

Kevin Yaniak - Contestar

The only way to remove it without breaking it is to use good scotch tape and completely cover the screen with a minimum 4 layers of tape. This will keep the screen intact - but you still have to be very careful.

Michael Griffiths - Contestar

That’s definitely not the only way. I just did it with a guitar pick and heat pad. After doing a ton of Surface Pro 3’s, I think this one is actually pretty easy in comparison.

austin -

I needed 3 hours for this, Did this the first time. There is everything glued. and real hard to not break the screen.

Dennis Reimer - Contestar

Can you put the screen back on after removing it?

Alex Shinnerl - Contestar

Agregar Comentario

Ver Estadísticas:

Ultimas 24 horas: 22

Ultimos 7 días: 125

Ultimos 30 días: 429

Todo El Tiempo: 50,332