Introducción

This repair guide will give instructions on how to remove the Macintosh PowerBook 1400c RAM.

Partes

No se requieren partes.

  1. Turn the device upside down and then locate the battery latch near the front of the device.
    • Turn the device upside down and then locate the battery latch near the front of the device.

    Agregar Comentario

  2. Slide the latch to the left to release the battery.
    • Slide the latch to the left to release the battery.

    Agregar Comentario

    • Continue holding the latch then gently pull the battery out of the device.

    • Place the battery in a safe location.

    Agregar Comentario

    • Locate the CD-ROM Drive latch.

    Agregar Comentario

    • Slide the latch to the right to release the CD ROM drive.

    Agregar Comentario

    • Continue holding the latch then gently pull the CD-ROM Drive out of the device.

    • Place the CD ROM drive in a safe location.

    Agregar Comentario

    • Locate the speaker cover.

    Agregar Comentario

    • Press firmly on each end of the speaker cover and slide it to the left.

    I found it was easy to get a spudger over the left edge and lift it up a bit, then push the bar to the left, It pops right off after that.

    Jimmy James - Contestar

    • Gently lift the speaker cover to remove it.

    Agregar Comentario

    • Lift the keyboard up from the back using a spudger(wedge side).

    Agregar Comentario

    • Gently lift the keyboard until only the ribbon cable remains attached.

    Agregar Comentario

    • Tilt the keyboard away from the screen.

    Agregar Comentario

    • Locate the six screws that secure the heatsink.

    This is not necessary to remove the HDD. Go directly to step 20.

    Kenneth DeVries - Contestar

    That isn't the HDD!

    Dix Dox - Contestar

    • Remove the six screws from the heatsink using the Philips #1 screwdriver.

    Agregar Comentario

    • Lift the heatsink from the side closest to the laptop screen.

    Agregar Comentario

    • Remove the heatsink.

    Agregar Comentario

    • Gently pull up on the beige ribbon lock until it moves a short distance on both sides to separate the ribbon cable from the connector.

    Agregar Comentario

    • Detach the ribbon cable.

    Agregar Comentario

    • Remove the keyboard.

    Agregar Comentario

    • Identify RAM Memory stick

    • These are the upgradeable RAM Memory sticks, they must be removed first

    Agregar Comentario

    • Gently grasp the ram on the far end as shown in the picture and then pull up and away from the right side of the computer

    Agregar Comentario

    • Remove the upgradeable RAM stick

    • If the upgradeable RAM stick is all you are repairing you can end the guide here, however to remove the factory installed RAM please continue

    Agregar Comentario

    • Gently grasp the factory installed RAM by grabbing each end as shown in the picture and pull the stick directly up

    Agregar Comentario

    • Remove the factory installed RAM memory module

    Agregar Comentario

Conclusión

To reassemble your device, follow these instructions in reverse order.

4 personas más completaron esta guía.

Kian Dinyari

Miembro Desde 07/04/11

125 Reputación

1 Guía escrita

Equipo

Cal Poly, Team 10-39, Forte Spring 2011 Miembro de Cal Poly, Team 10-39, Forte Spring 2011

CPSU-FORTE-S11S10G39

5 Miembros

6 Guías creadas

Agregar Comentario

Ver Estadísticas:

Ultimas 24 Horas: 0

Últimos 7 Días: 1

Últimos 30 Días: 10

Todo El Tiempo: 2,895