Saltar al contenido principal
  1. Retire los ocho tornillos Phillips de 4 mm que sujetan la carcasa inferior al MacBook.
    • Retire los ocho tornillos Phillips de 4 mm que sujetan la carcasa inferior al MacBook.

  2. La carcasa inferior está construida de aluminio recubierto de goma. No doble excesivamente el aluminio durante la extracción, ya que cualquier deformación permanente causará problemas de tolerancia después del reensamblaje. Levante ligeramente la tapa inferior cerca de la abertura de ventilación. Continúa pasando los dedos entre la parte superior e inferior hasta que salgan los clips de retención.
    • La carcasa inferior está construida de aluminio recubierto de goma. No doble excesivamente el aluminio durante la extracción, ya que cualquier deformación permanente causará problemas de tolerancia después del reensamblaje.

    • Levante ligeramente la tapa inferior cerca de la abertura de ventilación.

    • Continúa pasando los dedos entre la parte superior e inferior hasta que salgan los clips de retención.

    • La ubicación de estos tres clips se muestra en la tercera imagen.

  3. Por precaución, aconsejamos que desconectes el conector de la batería de la placa lógica para evitar ninguna descarga eléctrica. Este paso es opcional y no es requerido.
    • Por precaución, aconsejamos que desconectes el conector de la batería de la placa lógica para evitar ninguna descarga eléctrica. Este paso es opcional y no es requerido.

    • Usar la punta plana de una spudger para levantar el conector de la batería de su enchufe en la placa lógica.

    • Puede ser mas fácil usar tus uñas para levantar el conector en ambos lados

  4. Este paso está sin traducir. Ayuda a traducirlo

    Remove the following screws from the optical drive side of the rear vent:
    • Remove the following screws from the optical drive side of the rear vent:

    • Two 10 mm T8 Torx

    • Two 5.2 mm Phillips

  5. Este paso está sin traducir. Ayuda a traducirlo

    Remove the following screws from the port side of rear vent:
    • Remove the following screws from the port side of rear vent:

    • Two 10 mm T8 Torx

    • Two 5.2 mm Phillips

  6. Este paso está sin traducir. Ayuda a traducirlo

    Carefully lift the rear vent out of the upper case.
    • Carefully lift the rear vent out of the upper case.

  7. Este paso está sin traducir. Ayuda a traducirlo

    Remove the single 3 mm Phillips screw securing the AirPort/Bluetooth antenna ground strap to the rear speaker.
    • Remove the single 3 mm Phillips screw securing the AirPort/Bluetooth antenna ground strap to the rear speaker.

  8. Este paso está sin traducir. Ayuda a traducirlo

    Use the tip of a spudger to pry the AirPort and Bluetooth antenna connectors (3 total) up off the AirPort/Bluetooth card. De-route the long antenna from its channel in the rear speaker housing.
    • Use the tip of a spudger to pry the AirPort and Bluetooth antenna connectors (3 total) up off the AirPort/Bluetooth card.

    • De-route the long antenna from its channel in the rear speaker housing.

  9. Este paso está sin traducir. Ayuda a traducirlo

    Grab the plastic pull tab secured to the display data cable lock and rotate it toward the DC-In side of the computer. There is also a thin metal lock clip under the plastic tab that has to be released ( Use the tip of a spudger ) before you can disconnect the display data cable.
    • Grab the plastic pull tab secured to the display data cable lock and rotate it toward the DC-In side of the computer.

    • There is also a thin metal lock clip under the plastic tab that has to be released ( Use the tip of a spudger ) before you can disconnect the display data cable.

  10. Este paso está sin traducir. Ayuda a traducirlo

    Gently pull the display data cable connector away from its socket on the logic board. Pull the socket parallel to the face of the logic board.
    • Gently pull the display data cable connector away from its socket on the logic board.

    • Pull the socket parallel to the face of the logic board.

    • The display data cable socket is made of very thin metal and is easily bent. Be sure to pull the connector straight away from its socket.

  11. Este paso está sin traducir. Ayuda a traducirlo

    Open your MacBook so the display is perpendicular to the upper case.
    • Open your MacBook so the display is perpendicular to the upper case.

    • Place your opened MacBook on a table as pictured.

    • While holding the display and upper case together with your left hand, remove the remaining 7.8 mm with lock washer T8 Torx screw from the lower display bracket.

  12. Este paso está sin traducir. Ayuda a traducirlo

    Be sure to hold the display and upper case together with your left hand. Failure to do so may cause the freed display/upper case to fall, potentially damaging each component.
    • Be sure to hold the display and upper case together with your left hand. Failure to do so may cause the freed display/upper case to fall, potentially damaging each component.

    • Remove the last remaining T8 Torx screw securing the display to the upper case.

  13. Este paso está sin traducir. Ayuda a traducirlo

    Grab the upper case with your right hand and rotate it slightly toward the top of the display so the upper display bracket clears the edge of the upper case. The display data cable may cause the upper display bracket to get caught on the upper case. It may be helpful to slightly rotate the upper case away from the display  for more clearance.
    • Grab the upper case with your right hand and rotate it slightly toward the top of the display so the upper display bracket clears the edge of the upper case.

    • The display data cable may cause the upper display bracket to get caught on the upper case. It may be helpful to slightly rotate the upper case away from the display for more clearance.

    • Rotate the display slightly away from the upper case.

  14. Este paso está sin traducir. Ayuda a traducirlo

    Lift the display up and away from the upper case, minding any brackets or cables that may get caught.
    • Lift the display up and away from the upper case, minding any brackets or cables that may get caught.

  15. Este paso está sin traducir. Ayuda a traducirlo

    Insert the flat end of a spudger between the thin rubber strip surrounding the front display bezel and the rear display bezel. Do not try to insert the spudger between the thin rubber strip and the plastic face of the front display bezel. Use the flat end of your spudger to carefully pry the front display bezel away from the adhesive securing it to the rear display bezel.
    • Insert the flat end of a spudger between the thin rubber strip surrounding the front display bezel and the rear display bezel.

    • Do not try to insert the spudger between the thin rubber strip and the plastic face of the front display bezel.

    • Use the flat end of your spudger to carefully pry the front display bezel away from the adhesive securing it to the rear display bezel.

    • Do not pry against the fragile glass LCD panel. Also, do not excessively bend the plastic as it may permanently deform.

    • Continue prying until the front display bezel is free along the right side of the display and behind the right clutch hinge.

  16. Este paso está sin traducir. Ayuda a traducirlo

    Use the flat end of a spudger to pry the front display bezel off the top edge of the display assembly. It may be helpful to insert and twist the flat end of your spudger to enlarge the gap between the front & rear display bezels as you work your way around the edge of the display.
    • Use the flat end of a spudger to pry the front display bezel off the top edge of the display assembly.

    • It may be helpful to insert and twist the flat end of your spudger to enlarge the gap between the front & rear display bezels as you work your way around the edge of the display.

    • Continue separating until the top edge of the front display bezel is free from the display assembly.

    • Be careful when prying near the iSight camera board, as it has exposed circuitry and is delicate.

  17. Este paso está sin traducir. Ayuda a traducirlo

    Use your spudger to pry the left side of the front display bezel away from the display assembly. Carefully pry up the area behind the left clutch hinge.
    • Use your spudger to pry the left side of the front display bezel away from the display assembly.

    • Carefully pry up the area behind the left clutch hinge.

    • During reassembly, be sure the small plastic pegs on the front display bezel mate up with the holes in the rear display bezel (shown in red). Failure to do so will prevent the front display bezel from sitting flush against the rear bezel.

  18. Este paso está sin traducir. Ayuda a traducirlo

    Slowly work your way across the lower edge of the front display bezel until it is free from the display assembly. Be sure to pry up as far away from the LCD as possible, as it extends below the edge of the front display bezel. When you get about half way across, pry up from the other side of the front display bezel's lower edge to ease the process.
    • Slowly work your way across the lower edge of the front display bezel until it is free from the display assembly.

    • Be sure to pry up as far away from the LCD as possible, as it extends below the edge of the front display bezel.

    • When you get about half way across, pry up from the other side of the front display bezel's lower edge to ease the process.

  19. Este paso está sin traducir. Ayuda a traducirlo

    Remove the front display bezel from the display assembly.
    • Remove the front display bezel from the display assembly.

    • To help the adhesive avoid losing is tackiness, do not excessively handle the adhesive and be sure to keep it clean until you are ready for installation.

  20. Este paso está sin traducir. Ayuda a traducirlo

    Remove the two 3 mm Phillips screws securing the clutch cover to the rear display bezel.
    • Remove the two 3 mm Phillips screws securing the clutch cover to the rear display bezel.

  21. Este paso está sin traducir. Ayuda a traducirlo

    Insert the flat end of a spudger into the open end of the clutch cover and pry up to release it from the rear display bezel. Pry up from both sides of the clutch cover until it is completely free from the display assembly. Pry up from both sides of the clutch cover until it is completely free from the display assembly.
    • Insert the flat end of a spudger into the open end of the clutch cover and pry up to release it from the rear display bezel.

    • Pry up from both sides of the clutch cover until it is completely free from the display assembly.

  22. Este paso está sin traducir. Ayuda a traducirlo

    Remove the clutch cover from the display assembly.
    • Remove the clutch cover from the display assembly.

  23. Este paso está sin traducir. Ayuda a traducirlo

    Remove the three 4.7 mm T6 Torx screws securing the right clutch hinge to the rear display bezel.
    • Remove the three 4.7 mm T6 Torx screws securing the right clutch hinge to the rear display bezel.

  24. Este paso está sin traducir. Ayuda a traducirlo

    Remove the right clutch hinge from the rear display bezel.
    • Remove the right clutch hinge from the rear display bezel.

Linea de Meta

7 personas más completaron esta guía.

0 comentarios

Agregar Comentario

Ver Estadísticas:

Ultimas 24 horas: 0

Ultimos 7 días: 1

Ultimos 30 días: 7

Todo El Tiempo: 12,240