Saltar al contenido principal

Introducción

¡Reemplazar la tapa es fácil! Solo toma 8 tornillos.

  1. Retire los ocho tornillos Phillips de 4 mm que sujetan la carcasa inferior al MacBook.
    • Retire los ocho tornillos Phillips de 4 mm que sujetan la carcasa inferior al MacBook.

    According to this page http://support.apple.com/kb/HT1651?viewl..., the 8 screws are not identical.

    Can anybody tell me where each kind of screw is supposed to go?

    Gregoire - Contestar

    They are all 100% Identical. You were probably looking at a different model, or Apple has entered the wrong information... Hey, It happens...

    weeowey weeowey -

    The screws on the Late 2009 are identical. The blue lock compound might make tightening some require a little more effort.

    svenaustx - Contestar

    Can I replace it with a SATA 3 cable?

    nm - Contestar

    A1342 macbook does not have the right controller to support sata III

    weeowey weeowey -

    hi, i just got back from the apple store and they are really keen for me to upgrade to a new laptop since my battery is old and the screen is cracked, so glad i found ifixit i would love to upgrade this puppy! gonna make it a real sleeper! styler hall wrote about sticking 16 gb of ram in his a 1342 ? is this a simply mather of ordering 3 4gb sticks ?aslo i currently have 4 gb and would like to upgrade to 8 ( or indeed 16) does that mean i need to buy all new sticks or can i continue to use the old one and stick a new one next to it ?

    thanks again mick van aar, perth western aus.

    michelvanaar - Contestar

    The A1342 will take up to 16 GB of RAM, however, there are only two RAM slots, so use two 8-GB RAM modules. Other World Computing (OWC) is a great reference source for info on exactly which RAM to use with which model; prices are usually much better on EBay though. Add an SSD from OWC and your machine will really scream!

    I hope that helps!

    gdesbrisay -

    Gregoire is right. The 8 screws are absolutely NOT identical, I’m looking at them right now, weeowey weeowey.

    John Guzman - Contestar

    I just wanted to say that, in 2020, i used these instructions to replace the magsafe socket on my A1286, mid-2012, pre-Retina MacBook Pro. The internal layout is not quite the same but close enough for me to do the job. I skipped the steps of fully disconnecting the fans and speakers because of what others had said about breaking the sockets. it just meant I had to be extremely careful when lifting up the main board so that I did not tear and break the connections. I was able to disconnect the old magsafe socket with the board flat and in situ, but there was no where near enough room to be able to aline and press home the new par home. Reluctantly i had to lever up the board. This was difficult as there is a tapped post that holds a screw in the way close to where the USB sockets are, that prevented the board lifting up and out. I had to be quite forceful to manouevre the sockets out from the edge of the case.

    Paul Burridge - Contestar

  2. La carcasa inferior está construida de aluminio recubierto de goma. No doble excesivamente el aluminio durante la extracción, ya que cualquier deformación permanente causará problemas de tolerancia después del reensamblaje. Levante ligeramente la tapa inferior cerca de la abertura de ventilación. Continúa pasando los dedos entre la parte superior e inferior hasta que salgan los clips de retención.
    • La carcasa inferior está construida de aluminio recubierto de goma. No doble excesivamente el aluminio durante la extracción, ya que cualquier deformación permanente causará problemas de tolerancia después del reensamblaje.

    • Levante ligeramente la tapa inferior cerca de la abertura de ventilación.

    • Continúa pasando los dedos entre la parte superior e inferior hasta que salgan los clips de retención.

    • La ubicación de estos tres clips se muestra en la tercera imagen.

    Do the retaining clips have to be re-engaged when replacing the lower case?

    John Morley - Contestar

    Answering my own question, the clips re-engage when the lower case is correctly positioned. You can help them by gently pressing the lower case with your thumbs midway along the two short sides. When everything is correctly aligned the eight screw holes line up.

    John Morley -

    Rather than running your fingernail down the sides to free up the retaining clips, I found that using an old credit card, inserted about 1/4”, to run along the left and right side popped those end retaining clips right off with no problem. You may need to twist the card slightly when in the middle area to help pop those off.

    bdahl385 - Contestar

Conclusión

Para volver a armar su dispositivo, siga estas instrucciones en orden inverso.

73 personas más completaron esta guía.

Un agradecimiento especial a estos traductores:

en es

100%

¡ Matías Leguizamón nos está ayudando a reparar el mundo! ¿Quieres contribuir?
Empezar a traducir ›

2 comentarios

Apple has a recall on this part, so you can get a replacement for an improved version free and save yourself $149.99. Check out http://www.apple.com/support/macbook-bot...

Shane - Contestar

Would the Macbook Pro back cover also fit this?

wow - Contestar

Agregar Comentario

Ver Estadísticas:

Ultimas 24 horas: 2

Ultimos 7 días: 24

Ultimos 30 días: 93

Todo El Tiempo: 67,714