Repara tus cosas Comunidad Tienda

Esta versión puede contener ediciones incorrectas. Cambiar a la última instantánea verificada.

Qué necesitas

  1. , Puerta de acceso: paso 1, imagen 1 de 1

    • Con la carcasa cerrada, coloca el Unibody con la parte superior hacia abajo sobre una superficie plana.

    • Presiona el lado ranurado de la pestaña de apertura de la puerta de acceso, lo suficiente como para poder agarrar el extremo libre. Levanta la pestaña de apertura hasta que quede vertical.

    Traducir

  2. : paso 2, imagen 1 de 1

    • La puerta de acceso debe estar ahora lo suficientemente separada, como para levantarla y sacarla del Unibody.

    Traducir

  3. , Batería: paso 3, imagen 1 de 1

    • Antes de seguir, asegúrate de que la pestaña de apertura de la tapa de acceso esté vertical.

    • Sujeta la pestaña de plástico blanco y extrae la batería del Unibody.

    Traducir

  4. , Carcasa inferior: paso 4, imagen 1 de 1

    • Retira los siguientes ocho tornillos que aseguran la carcasa inferior al chasis:

    • Un tornillo Phillips de 3 mm.

    • Tres tornillos Phillips de 13.5 mm.

    • Cuatro tornillos Phillips de 3.5 mm.

    Traducir

  5. : paso 5, imagen 1 de 1

    • Usando ambas manos, levanta y retira la carcasa inferior de la carcasa superior.

    Traducir

  7. Este paso está sin traducir. Ayuda a traducirlo

    : paso 6, imagen 1 de 1

    • Disconnect the camera cable by pulling the male end straight away from its socket.

    • Be careful not to pull up on the cable as you remove it from the socket.

    Traducir

  8. Este paso está sin traducir. Ayuda a traducirlo

    : paso 7, imagen 1 de 2 : paso 7, imagen 2 de 2

    • De-route the camera data cable from the channel in the optical drive.

    Traducir

  9. Este paso está sin traducir. Ayuda a traducirlo

    : paso 8, imagen 1 de 2 : paso 8, imagen 2 de 2

    • Remove the following screws securing the camera data cable and right speaker to the upper case:

    • One 9.9 mm partially threaded Phillips screw

    • One 9.6 mm threaded Phillips screw

    • One 4 mm Phillips screw

    • Slide the camera cable bracket out from under the subwoofer and remove it from the computer.

    • The iSight cable has an eyelet through which passes the left-most screw in these pictures.

    Traducir

  10. Este paso está sin traducir. Ayuda a traducirlo

    : paso 9, imagen 1 de 2 : paso 9, imagen 2 de 2

    • Grab the plastic pull tab secured to the display data cable lock and rotate it toward the DC-in side of the computer.

    • Pull the display data cable connector straight away from its socket.

    • Make sure to pull the connector straight away and not straight up from its socket.

    Traducir

  11. Este paso está sin traducir. Ayuda a traducirlo

    : paso 10, imagen 1 de 2 : paso 10, imagen 2 de 2

    • Remove the following two screws from the display data cable bracket:

    • One 7 mm Phillips screw.

    • One 5 mm Phillips screw.

    • Lift the display data cable bracket out of the upper case.

    Traducir

  12. Este paso está sin traducir. Ayuda a traducirlo

    : paso 11, imagen 1 de 1

    • Remove the two outer 6 mm Torx screws securing each side of the display to the upper case (4 screws total).

    Traducir

  13. Este paso está sin traducir. Ayuda a traducirlo

    : paso 12, imagen 1 de 1

    • Open your MacBook so the display is perpendicular to the upper case.

    • Place your opened MacBook on a table as pictured.

    • While holding the display and upper case together with your left hand, remove the 6 mm Torx screw from the lower display bracket.

    Traducir

  14. Este paso está sin traducir. Ayuda a traducirlo

    : paso 13, imagen 1 de 1

    • Be sure to hold the display and upper case together with your left hand. Failure to do so may cause the freed display/upper case to fall, potentially damaging each component.

    • Remove the last remaining 6 mm Torx screw securing the display to the upper case.

    Traducir

  15. Este paso está sin traducir. Ayuda a traducirlo

    : paso 14, imagen 1 de 3 : paso 14, imagen 2 de 3 : paso 14, imagen 3 de 3

    • Grab the upper case with your right hand and rotate it slightly toward the top of the display so the upper display bracket clears the edge of the upper case.

    • Rotate the display slightly away from the upper case.

    • Lift the display away from the upper case, minding any brackets or cables that may get caught.

    Traducir
Linea de Meta

61 personas más completaron esta guía.

4 comentarios

This worked perfectly. My brother had an old MacBook laying around that he had fried when he spilled a drink on it. As a result it sat for a few years after he bought a new computer. His top case was ruined and after some pestering gave me his "broken" mac. I just finished swapping the displays, my computer was 6 years old and my display had dead pixels and a broken isight(for the last three years!) Swapping the display assembly fixed everything. Total time: 2 hrs.

NOTE: Be very careful when removing the cables, always use less force then you think you need, you should be good to go!

Melanie B - Contestar

My display has a huge stripe down the middle that is inverse contrast. When I have the display in a certain position, like if I bend the screen ALL the way back, it'll be fine but mostly the stripe will pop back. This leads me to think the display cable is loose or not seated properly. I got to about step 9 in this guide, cleaned the connectors and re-seated but it's still there. Any ideas? I think the cable might be messed up when it goes into the black plastic hinge part. Seems pinched?

antiboyo - Contestar

Curious if you made any progress here -- my brother has exactly the same issue. I'm planning on replacing the assembly outright, but going to open it up first just to see if I can "un-pinch" it. If it's just the cable, I was thinking of replacing it, but it looks like I'd have to take the display apart more which I'm not up to doing (heat gun etc.).

Mark Ahrens -

Hey, just so you guys know, reassembling the display is a little tricky. The display might not go on straight, so don't tighten down all of the screws until you are sure the display is straight. You might not even have that problem, but I did with my MacBook.

lyonmissions - Contestar

Agregar Comentario

Ver Estadísticas:

Ultimas 24 horas: 1

Ultimos 7 días: 13

Ultimos 30 días: 90

Todo El Tiempo: 97,710