Esta versión puede contener ediciones incorrectas. Cambiar a la última instantánea verificada.
Qué necesitas
-
-
Utiliza los dedos para empujar las dos lengüetas de liberación de la batería y sácala del ordenador.
-
-
-
Retira los cuatro tornillos Phillips idénticos de 3,4 mm de la puerta de la memoria. Estos tornillos tienen cabezas de 4 mm de diámetro en lugar de las cabezas de 3 mm de los tornillos del cuerpo.
-
-
-
Retira los tres tornillos Phillips del compartimento de la batería, cerca del pestillo. Apple tuvo la amabilidad de inclinar estos tornillos en un ligero ángulo para facilitar su extracción. En el A1261 estos tornillos tienen cabezas de 4 mm de diámetro en lugar de las cabezas de 3 mm en los tornillos del cuerpo.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Disconnect the two antenna cables from the AirPort Extreme card, the iSight and inverter cables from the left side of the logic board, and the display data cable from the right side of the logic board. Be careful to slide the connectors as they may become damaged otherwise.
-
Carefully peel the iSight and inverter cables off the top of the left fan and de-route the AirPort antenna cables from the channel in the left speaker.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the ten silver T6 Torx screws securing the display (five on each side-take note that the inside screws on both sides are longer with a thinner head).
-
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Grasp the display assembly on both sides and lift it up and out of the computer.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the Phillips screws from the lower left and right corners of the display (two screws total).
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Insert the flat end of a spudger perpendicular to the face of the display between the plastic strip attached to the rear bezel and the front bezel.
-
With the spudger still inserted, rotate it away from the display to separate the front and rear bezels.
-
Work along the right edge of the display until the rear bezel is evenly separated from the front bezel.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Insert your spudger between the front and rear display bezels at the lower right corner of the display.
-
Pry the rear bezel away from the front bezel to slightly separate the bottom edge of the rear display bezel.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Insert the flat end of a spudger into the gap between the rear display bezel and the clutch cover.
-
Twist the spudger to separate the lower edge of the rear display bezel from the clutch cover.
-
Work along the lower edge of the rear bezel until it is evenly separated from the clutch cover.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Now that the right and bottom edges of the rear bezel are slightly separated from the front bezel, use a spudger to pop the rear bezel off the tabs near the lower right corner of the display.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Insert the flat end of a spudger between the front bezel and the plastic strip attached to the rear bezel near the screw holes at the bottom corners of the display.
-
Rotate your spudger toward the rear bezel to separate it from the front bezel.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Slightly lift the lower edge of the display and pull it away from the rear display bezel.
-
The rear display bezel remains.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the piece of tape securing the backlight cables to the front display bezel.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Carefully lift the inverter out of the clutch cover.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Disconnect the inverter cable by pulling its connector away from the socket on the inverter board.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Disconnect the backlight connector from the inverter board.
-
Remove the inverter from the display.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Use the flat end of a spudger to carefully peel off the three antenna straps stuck to the lower edge of the LCD.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the five Phillips screws securing the clutch cover to the bottom edge of the front display bezel.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the two pieces of tape securing the display data cable to the LCD.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Disconnect the display data cable from the LCD by pulling it toward the bottom edge of the display.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Move the display data cable out of the way to remove the Phillips screw hidden underneath.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
While pulling the clutch assembly away from the clutch hinge with one hand, insert an iPod opening tool between the clutch cover and the front display bezel to lift the clutch cover over the retaining pin on the front display bezel.
-
Pull the clutch assembly away from the front display bezel.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Repeat the process covered in the previous step to free the other side of the clutch assembly from the front display bezel.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the clutch assembly from the front display bezel, minding any cables that may get caught.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the five small Phillips screws securing the plastic antenna cover to the inside of the clutch cover.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Pull the antenna cover off the clutch cover, being careful not to damage the antenna cables.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
If necessary, peel the antenna leads off the adhesive securing them to the clutch cover.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the antenna cables from the clutch cover, being careful not to damage the three antenna straps.
-
Cancelar: No complete esta guía.
4 personas más completaron esta guía.