Esta versión puede contener ediciones incorrectas. Cambiar a la última instantánea verificada.
Qué necesitas
-
-
Quitar los siguientes tornillos pentalobe que sujetan la tapas inferior del MacBook Pro:
-
Ocho 3.0 mm
-
Dos 2.3 mm
-
-
-
Retira la etiqueta de advertencia que cubre el conector de la batería
-
-
-
Usando el extremo plano de un spudger, levanta suavemente el conector de la batería directamente fuera de su zócalo en la placa lógica.
-
Dobla los cables de la batería hacia afuera y fuera del camino, asegurándose de que el conector de la batería no entre en contacto accidentalmente con la placa lógica.
-
-
-
Usa la punta de un spudger para levantar los tres cables de antena AirPort directamente de sus enchufes en la placa AirPort.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Use the flat end of a spudger to pry the rubber hinge covers up off the left and right hinges.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the two 3.1 mm T5 Torx screws securing the aluminum hinge covers to the upper case.
-
Remove the two aluminum hinge brackets from the MacBook Pro.
-
-
-
Utilizando el extremo plano de un spudger, haz palanca en el conector de la placa de E/S para sacarlo de su zócalo en la placa lógica.
-
De la misma manera, retira el conector del cable de la tarjeta de E/S de su zócalo en la tarjeta de E/S.
-
Retira el cable de la placa de E/S de MacBook Pro.
-
-
-
Retira el único tornillo Torx T5 de 2,9 mm que sujeta la tarjeta AirPort a la placa lógica.
-
-
-
Usa la punta de un spudger para levantar la aleta de retención del zócalo ZIF del cable plano del ventilador derecho.
-
Comenzando en la parte superior del cable, desliza una herramienta de apertura de plástico debajo del cable del ventilador derecho para liberarlo de la placa lógica.
-
-
-
-
Usa el extremo plano de un spudger para levantar la tapa del disipador de calor de goma del ventilador izquierdo.
-
-
-
Usa la punta de un spudger para levantar la aleta de retención del zif ZIF del cable de cinta del ventilador izquierdo.
-
Comenzando en la parte superior del cable, desliza una herramienta de apertura de plástico debajo del cable del ventilador izquierdo para liberarlo de la placa lógica.
-
Levanta el ventilador izquierdo del dispositivo.
-
-
-
Retira el solo tornillo Torx T5 de 3,1 mm que asegura la SSD a la placa lógica.
-
-
-
Usa la punta de un spudger para levantar el bloqueo del cable de datos de la placa de E / S y gíralo hacia el lado de la batería de la computadora.
-
Usa el extremo plano de un spudger para deslizar el cable de datos de la placa de E / S directamente fuera de su zócalo en la placa lógica.
-
-
-
Retira los dos tornillos Torx T5 de 3,1 mm que sujetan la placa de E / S a la placa lógica.
-
En algunos modelos, retirar también el tornillo Torx plateado de 3,5 mm T5 del disipador puede ayudar a retirar la placa de E/S.
-
Levanta con cuidado la placa de E/S y retírela de la carcasa inferior.
-
-
-
Usa el extremo plano de un spudger para levantar el conector del conector de auriculares de su zócalo en la placa lógica.
-
-
-
Levantando desde el lado más cercano a la batería, gira la placa lógica hacia la parte superior de la MacBook Pro.
-
Usando el extremo plano de un spudger, empuja con cuidado el conector MagSafe 2 fuera de su zócalo en la parte inferior de la placa lógica.
-
En el sentido de las agujas del reloj desde la parte superior: teclado, panel táctil, batería, altavoz derecho, del teclado, pantalla, micrófono, toma de auriculares, altavoz izquierdo.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the single 2.6 mm T5 Torx screw securing the left rubber hinge cover in place.
-
Slide the hinge cover out of its bezel, then lift it up and out of the device.
-
Slide the right cover out of its bezel, then lift it out of the device.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Insert the edge of a plastic opening tool underneath the upper microphone.
-
Slide the blade of a plastic opening tool along the bottom of the upper microphone, releasing the adhesive.
-
In a similar manner, release the adhesive underneath the lower microphone.
-
Lift the cable out of the device.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the two 4.0 mm T5 Torx screws securing the MagSafe DC-In board to the upper case.
-
Slide the MagSafe DC-In board towards the right free it from its recess within the upper case.
-
Lift and remove the MagSafe DC-In board out of the upper case assembly.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the two 3.6 mm T5 Torx screws securing the headphone jack to the upper case assembly.
-
Slide the headphone jack away from the upper case.
-
Lift and remove the headphone jack out from its recess in the upper case.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the following three screws securing the left speaker to the upper case:
-
One 5.6 mm T5 Torx screw
-
One 6.9 mm T5 Torx screw
-
One 2.6 mm T5 Torx screw
-
Lift the left speaker out of the upper case and set it aside.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the following three screws securing the right speaker to the upper case:
-
One 5.6 mm T5 Torx screw
-
One 6.9 mm T5 Torx screw
-
One 2.6 mm T5 Torx screw
-
Remove the right speaker from the MacBook Pro.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove four out of the six 5.3 mm T8 Torx screws securing the display to the upper case.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
While supporting both halves of the device with one hand, unscrew the upper 5.3 mm T8 Torx screw.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Grip both halves of the device. Firmly put one hand on the top center of the upper case (left) and one in the same place on the display assembly (right).
-
While holding the display assembly in place, slowly push forward on the upper case, releasing it from the display assembly.
-
Cancelar: No complete esta guía.
51 personas más completaron esta guía.
10 comentarios
How Can I clean a coffee spill on the retina macbook pro? which alcohol to use to clean the logic board and I/O board? Will I get all the necessary tools to open it in Home Tech toolkit?
-It would be cool a 3rd party battery manufacturer to make a spare battery without the glue.
-Ony needed to remove the glued one (no prob. if damage it.. it is no good anyway, anymore) and put in place a new one with no glue held in place just by the lack of space inside the case, or some tiny spongy strips to help remove any play.
-The thing is who would manufacture a spare like this.
-Even Apple could supply spares like this.
I have always turned to iFixIt for repair guides. This particular repair, listed as "difficult," was one that I was apprehensive about undertaking. But I was successful!
I have a brief blog post about it here:
http://www.hightechdad.com/2014/12/22/ho...
And, for those who are going through this guide, I have a LONG (30 minute) video that walks through the repair using the iFixIt guide:
https://www.youtube.com/watch?v=2ODfFSMs...
Hope it helps!
-HTD
== The good ==
Very clear instructions, well done.
== The warning ==
There is one major problem though ... I purchased the Upper Case Assembly as mentioned, although from a local retailer in Australia. When I got to the final step, I realised it didn't have the battery or touchpad. If you purchase the case assembly from elsewhere, make sure it comes with the battery/touchpad as these are impossible to move from one unit to another.