Saltar al contenido principal
  1. follow steps to remove bottom case if needed. how to remove bottom case. with bottom case removed, begin with disconnecting the battery. this is done by fist moving the ribbon cable out of the way of the screw that secures the battery contact. Once unscrewed, lift flap to interrupt contact to battery. with bottom case removed, begin with disconnecting the battery. this is done by fist moving the ribbon cable out of the way of the screw that secures the battery contact. Once unscrewed, lift flap to interrupt contact to battery.
    • follow steps to remove bottom case if needed. how to remove bottom case.

    • with bottom case removed, begin with disconnecting the battery. this is done by fist moving the ribbon cable out of the way of the screw that secures the battery contact. Once unscrewed, lift flap to interrupt contact to battery.

  2. next, remove the antenna bar. unlike the previous generation MacBook pros, the wifi antenna is not attached to the display assembly. To remove the antenna bar, start by removing the 12 screws located above the left/right heat sink vents by using a Pentalobe-2 (P2) bit. next, remove the shield plates by taking out the 8 T3 screws circled in green.
    • next, remove the antenna bar. unlike the previous generation MacBook pros, the wifi antenna is not attached to the display assembly.

    • To remove the antenna bar, start by removing the 12 screws located above the left/right heat sink vents by using a Pentalobe-2 (P2) bit.

    • next, remove the shield plates by taking out the 8 T3 screws circled in green.

    • after the shields are removed, lift up on the center snap-in connector on the antenna bar.

  3. Kits de reparación de iPhone X

    ¿Garantía vencida? No te preocupes, tenemos la solución.

    Comprar Ahora

    Kits de reparación de iPhone X

    ¿Garantía vencida? No te preocupes, tenemos la solución.

    Comprar Ahora
  4. remove the t3 screws securing the antenna bar in place. disconnect the antenna cables and remove the bracket screw located beneath the cables. disconnect the antenna cables and remove the bracket screw located beneath the cables.
    • remove the t3 screws securing the antenna bar in place.

    • disconnect the antenna cables and remove the bracket screw located beneath the cables.

  5. remove antenna bar by lifting and sliding it out of the unit. The antenna cables will slide out from underneath the heatsink and through an opening located where the red arrow is pointing. remove antenna bar by lifting and sliding it out of the unit. The antenna cables will slide out from underneath the heatsink and through an opening located where the red arrow is pointing. remove antenna bar by lifting and sliding it out of the unit. The antenna cables will slide out from underneath the heatsink and through an opening located where the red arrow is pointing.
    • remove antenna bar by lifting and sliding it out of the unit. The antenna cables will slide out from underneath the heatsink and through an opening located where the red arrow is pointing.

  6. with the antenna bar removed, it is now time to remove display assembly. it is recommended to have the display at 90degree angle for removal. remove the screws indicated by the red circles. (*there will be a plastic black covering over the display hinges. it will need to be removed first to expose the hinges.) with the antenna bar removed, it is now time to remove display assembly. it is recommended to have the display at 90degree angle for removal. remove the screws indicated by the red circles. (*there will be a plastic black covering over the display hinges. it will need to be removed first to expose the hinges.)
    • with the antenna bar removed, it is now time to remove display assembly. it is recommended to have the display at 90degree angle for removal. remove the screws indicated by the red circles. (*there will be a plastic black covering over the display hinges. it will need to be removed first to expose the hinges.)

Conclusión

To reassemble your device, follow these instructions in reverse order.

17 personas más completaron esta guía.

What is the ribbon cable that you must remove before disconnecting the battery do?

Max4r - Contestar

your mom.

all joking aside, its the communication between the logic board and the battery controller (cycle count, battery health etc)

Joe Jankins -

Hello

In Step 5 you indicate to remove the screws in the red circles, what about the ribbon cables below the central red-circled screws? Those ribbon cables seem to connect the screen to the motherboard.

Best regards

Alex

info - Contestar

It's like this company started as a passionate team who wanted to be the first to present fool-proof instructions how to repair your own device and now everyone's like slacking off and got bored. Why not describe the first thing we're removing? Why are you no longer giving the screw dimensions? Why are you skipping steps? Where is the LCD cable? Where is pretty white background? Why is this guide not on the A1706 main page?

skia.021 - Contestar

I agree.

What about required tools? Seems like even the basics are missing or lacking.

Jimmy M -

Agregar Comentario

Ver Estadísticas:

Ultimas 24 Horas: 0

Últimos 7 Días: 136

Últimos 30 Días: 1,077

Todo El Tiempo: 20,769