Repara tus cosas Comunidad Tienda

MacBook Pro 13" Retina Display Late 2013 Heat Sink Replacement

Introducción

Use this guide to remove or replace the heat sink.

Don't forget to follow our thermal paste application guide after you have removed your heat sink.

Qué necesitas

  1. MacBook Pro 13" Retina Display Late 2013 Heat Sink Replacement, Lower Case: paso 1, imagen 1 de 1
    Herramienta utilizada en este paso:
    Magnetic Project Mat
    $19.95
    Comprar

    • Remove the following ten screws securing the lower case to the upper case:

    • Two 2.3 mm P5 Pentalobe screws

    • Eight 3.0 mm P5 Pentalobe screws

    • Throughout this repair, keep track of each screw and make sure it goes back exactly where it came from to avoid damaging your device.

    Traducir

  2. MacBook Pro 13" Retina Display Late 2013 Heat Sink Replacement: paso 2, imagen 1 de 1

    • Wedge your fingers between the upper case and the lower case.

    • Gently pull the lower case away from the upper case to remove it.

    Traducir

  3. MacBook Pro 13" Retina Display Late 2013 Heat Sink Replacement: paso 3, imagen 1 de 2 MacBook Pro 13" Retina Display Late 2013 Heat Sink Replacement: paso 3, imagen 2 de 2

    • The lower case is connected to the upper case with two plastic clips near its center.

    • During reassembly, gently push down the center of the lower case to reattach the two plastic clips.

    Traducir

  4. MacBook Pro 13" Retina Display Late 2013 Heat Sink Replacement, Battery Connector: paso 4, imagen 1 de 1

    • If necessary, remove the plastic cover adhered to the battery contact board.

    Traducir

  6. MacBook Pro 13" Retina Display Late 2013 Heat Sink Replacement: paso 5, imagen 1 de 2 MacBook Pro 13" Retina Display Late 2013 Heat Sink Replacement: paso 5, imagen 2 de 2

    • Use the flat end of a spudger to lift the battery connector straight up out of its socket on the logic board.

    • Be sure you lift up only on the connector itself, not the socket, or you risk permanent damage to the logic board.

    Traducir

  7. MacBook Pro 13" Retina Display Late 2013 Heat Sink Replacement: paso 6, imagen 1 de 1

    • Bend the battery connector up out of the way to prevent accidental contact with its socket during your repair.

    Traducir

  8. MacBook Pro 13" Retina Display Late 2013 Heat Sink Replacement, Heat Sink: paso 7, imagen 1 de 3 MacBook Pro 13" Retina Display Late 2013 Heat Sink Replacement, Heat Sink: paso 7, imagen 2 de 3 MacBook Pro 13" Retina Display Late 2013 Heat Sink Replacement, Heat Sink: paso 7, imagen 3 de 3

    • Carefully remove the rubber fan bumper from the edge of the heat sink.

    • The fan bumper wraps around the heat sink and fits into slots in the fan duct. During reassembly, be sure to fit the tabs into the notches in the fan duct.

    Traducir

  9. MacBook Pro 13" Retina Display Late 2013 Heat Sink Replacement: paso 8, imagen 1 de 2 MacBook Pro 13" Retina Display Late 2013 Heat Sink Replacement: paso 8, imagen 2 de 2

    • Use the flat end of a spudger to peel the four foam stickers off of the heat sink screws.

    Traducir

  10. MacBook Pro 13" Retina Display Late 2013 Heat Sink Replacement: paso 9, imagen 1 de 1

    • Remove the following screws securing the heat sink to the logic board:

    • Four 2.6 mm T5 screws

    • One 2.4 mm Phillips #000 screw

    Traducir

  11. MacBook Pro 13" Retina Display Late 2013 Heat Sink Replacement: paso 10, imagen 1 de 2 MacBook Pro 13" Retina Display Late 2013 Heat Sink Replacement: paso 10, imagen 2 de 2
    Traducir
Conclusión

To reassemble your device, follow these instructions in reverse order.

22 personas más completaron esta guía.

Autor

con 4 otros colaboradores

Sam Goldheart

Miembro Desde 10/18/12

465,647 Reputación

538 Guías creadas

Insignias: 48

+ 45 más insignias

Equipo

iFixit Miembro de iFixit

Staff

135 Miembros

16,732 Guías creadas

Un comentario

If you are following this guide to replace the thermal paste on the CPU i think you should know that - if you, like i, have decided to remove the black electrical tape that is on the CPU, make sure you are super careful when using Thermal Paste Remover Liquid. Any liquid can easily get under the CPU because there is enough gap from every side.

My Mac lives but now i live with the memory of worryingly wondering whether i killed it while cleaning out the liquid from underneath the CPU without lifting it.

Alexander - Contestar

Agregar Comentario

Ver Estadísticas:

Ultimas 24 horas: 6

Ultimos 7 días: 34

Ultimos 30 días: 136

Todo El Tiempo: 23,172