Repara tus cosas Comunidad Tienda

MacBook Pro 13" Retina Display Early 2015 Trackpad Cable Replacement

Sólo Prerrequisito
Esta guía solo debería usarse como prerrequisito para otras guías. Por tanto, estará incompleta.

Qué necesitas

  1. MacBook Pro 13" Retina Display Early 2015 Trackpad Cable Replacement, Trackpad Cable: paso 1, imagen 1 de 2 MacBook Pro 13" Retina Display Early 2015 Trackpad Cable Replacement, Trackpad Cable: paso 1, imagen 2 de 2

    • Use the flat end of a spudger to pop the trackpad connector straight up off its socket on the logic board.

    Editar

  2. MacBook Pro 13" Retina Display Early 2015 Trackpad Cable Replacement: paso 2, imagen 1 de 2 MacBook Pro 13" Retina Display Early 2015 Trackpad Cable Replacement: paso 2, imagen 2 de 2

    • Lift the trackpad cable up off the battery to separate it from the adhesive securing it.

    • Be careful not to damage the cable. If it doesn't peel up easily, apply a little heat from an iOpener, heat gun, or hair dryer to soften the adhesive, and try again.

    • If you are installing a new trackpad cable, be sure to fold the new cable to match the shape of the old cable. The new cable will appear to be too long if it is not folded.

    Editar

  4. MacBook Pro 13" Retina Display Early 2015 Trackpad Cable Replacement: paso 3, imagen 1 de 3 MacBook Pro 13" Retina Display Early 2015 Trackpad Cable Replacement: paso 3, imagen 2 de 3 MacBook Pro 13" Retina Display Early 2015 Trackpad Cable Replacement: paso 3, imagen 3 de 3

    • If necessary, peel back any tape covering the trackpad cable connector.

    • Use the end of a spudger to flip the retaining tab on the ZIF connector.

    Editar

  5. MacBook Pro 13" Retina Display Early 2015 Trackpad Cable Replacement: paso 4, imagen 1 de 2 MacBook Pro 13" Retina Display Early 2015 Trackpad Cable Replacement: paso 4, imagen 2 de 2

    • Pull the trackpad cable straight out of its ZIF socket on the trackpad control board.

    • During reassembly, make sure that the retaining tab is in the up, "unlocked" position before you insert the cable into the socket.

    Editar

  6. MacBook Pro 13" Retina Display Early 2015 Trackpad Cable Replacement: paso 5, imagen 1 de 1

    • Remove the single 3.7 mm T5 Torx screw securing the battery board to the upper case.

    Editar
Conclusión

To reassemble your device, follow these instructions in reverse order.

3 personas más completaron esta guía.

Autor

con 6 otros colaboradores

Sam Goldheart

Miembro Desde 10/18/12

465,738 Reputación

538 Guías creadas

Insignias: 48

+ 45 más insignias

Equipo

iFixit Miembro de iFixit

Staff

135 Miembros

16,767 Guías creadas

3 comentarios

Why remove the screw in step 5?

Ari Cooper - Davis - Contestar

Yes @sam , why should you remove the screw in step 5? Is this a mistake?

lmdehaas - Contestar

Step 5: Remove the single 3.7 mm T5 Torx screw.

Step 6: Re-screw single 3.7 mm T5 Torx screw.

David Grabowski - Contestar

Agregar Comentario

Ver Estadísticas:

Ultimas 24 horas: 0

Ultimos 7 días: 0

Ultimos 30 días: 0

Todo El Tiempo: 1,782