Repara tus cosas Comunidad Tienda

MacBook Pro 13" Retina Display Early 2013 SSD Replacement

Introducción

Use this guide to upgrade or replace the solid-state drive in a MacBook Pro 13” Early 2013. This MacBook Pro uses a proprietary storage drive connector, and is therefore not compatible with common M.2 drives without the use of an adapter.

Before you perform this repair, if at all possible, back up your existing SSD. Then, either familiarize yourself with internet recovery or create a bootable external drive so you’ll be ready to install macOS onto your new drive and migrate your data to the new SSD.

Finally, we strongly recommend installing macOS 10.13 High Sierra (or a later macOS) before replacing the original SSD from your MacBook Pro. Most new SSDs require updated storage drivers not found in versions of macOS prior to High Sierra.

Qué necesitas

  1. MacBook Pro 13" Retina Display Early 2013 SSD Replacement, Lower Case: paso 1, imagen 1 de 1
    Herramienta utilizada en este paso:
    Magnetic Project Mat
    $19.95
    Comprar

    • Remove the following ten screws securing the lower case to the upper case:

    • Two 2.3 mm P5 Pentalobe screws

    • Eight 3.0 mm P5 Pentalobe screws

    • Throughout this repair, keep track of each screw and make sure it goes back exactly where it came from to avoid damaging your device.

    Traducir

  2. MacBook Pro 13" Retina Display Early 2013 SSD Replacement: paso 2, imagen 1 de 1

    • Wedge your fingers between the upper case and the lower case.

    • Gently pull the lower case away from the upper case.

    • Remove the lower case and set it aside.

    Traducir

  3. MacBook Pro 13" Retina Display Early 2013 SSD Replacement: paso 3, imagen 1 de 3 MacBook Pro 13" Retina Display Early 2013 SSD Replacement: paso 3, imagen 2 de 3 MacBook Pro 13" Retina Display Early 2013 SSD Replacement: paso 3, imagen 3 de 3

    • During reassembly, gently push down the center of the lower case to reattach the two plastic clips.

    • The lower case is connected to the upper case at the center, with two plastic clips.

    Traducir

  4. MacBook Pro 13" Retina Display Early 2013 SSD Replacement, Battery Connector: paso 4, imagen 1 de 1

    • Remove the plastic cover adhered to the battery contact board.

    Traducir

  5. MacBook Pro 13" Retina Display Early 2013 SSD Replacement: paso 5, imagen 1 de 1

    • Remove the following screws securing the battery connector board to the logic board:

    • Two 2.8 mm T6 Torx screws

    • One 7.0 mm T6 Torx shouldered screw

    Traducir

  6. MacBook Pro 13" Retina Display Early 2013 SSD Replacement: paso 6, imagen 1 de 2 MacBook Pro 13" Retina Display Early 2013 SSD Replacement: paso 6, imagen 2 de 2

    • Use tweezers to remove the small plastic cover located near the bottom right of the battery connector board.

    Traducir

  8. MacBook Pro 13" Retina Display Early 2013 SSD Replacement: paso 7, imagen 1 de 1

    • Remove the wide head 6.4 mm T6 Torx screw securing the battery connector to the logic board assembly.

    Traducir

  9. MacBook Pro 13" Retina Display Early 2013 SSD Replacement: paso 8, imagen 1 de 2 MacBook Pro 13" Retina Display Early 2013 SSD Replacement: paso 8, imagen 2 de 2

    • Carefully lift the battery connector board up off the logic board.

    • It is recommended to bend the battery cables just slightly, to keep the board suspended up above the logic board and out of the way.

    • Do not fold the board completely over, or crease the cables, as this may damage the battery.

    Traducir

  10. MacBook Pro 13" Retina Display Early 2013 SSD Replacement, Battery Contact Board: paso 9, imagen 1 de 2 MacBook Pro 13" Retina Display Early 2013 SSD Replacement, Battery Contact Board: paso 9, imagen 2 de 2

    • Grasp the Interposer with tweezers.

    • An interposer is the name for an interface that links one electrical connection to another. In this repair, it is the board connecting the battery to logic board.

    • Lift the Interposer off the logic board and remove it.

    • Removing this board will ensure that the battery remains disconnected throughout your repair, preventing your computer from accidentally powering on. It's also a good idea to take it out so it doesn't fall out unexpectedly.

    Traducir

  11. MacBook Pro 13" Retina Display Early 2013 SSD Replacement, SSD Assembly: paso 10, imagen 1 de 2 MacBook Pro 13" Retina Display Early 2013 SSD Replacement, SSD Assembly: paso 10, imagen 2 de 2

    • Use the flat end of a spudger to pry the SSD cable connector up from its socket on the logic board.

    Traducir

  12. MacBook Pro 13" Retina Display Early 2013 SSD Replacement: paso 11, imagen 1 de 3 MacBook Pro 13" Retina Display Early 2013 SSD Replacement: paso 11, imagen 2 de 3 MacBook Pro 13" Retina Display Early 2013 SSD Replacement: paso 11, imagen 3 de 3

    • Use your thumb or finger to bend the plastic spring bar on the SSD tray, freeing the two clips at the front side of the device.

    • While holding the spring bar depressed, tilt the SSD assembly up out of its cavity.

    Traducir

  13. MacBook Pro 13" Retina Display Early 2013 SSD Replacement: paso 12, imagen 1 de 1

    • Remove the SSD assembly from the upper case.

    Traducir

  14. MacBook Pro 13" Retina Display Early 2013 SSD Replacement: paso 13, imagen 1 de 1

    • Remove the single 2.9 mm T5 Torx screw securing the SSD to the SSD tray.

    Traducir

  15. MacBook Pro 13" Retina Display Early 2013 SSD Replacement: paso 14, imagen 1 de 2 MacBook Pro 13" Retina Display Early 2013 SSD Replacement: paso 14, imagen 2 de 2

    • Insert the edge of plastic opening tool between the SSD and the SSD tray, opposite to the socket side of SSD tray.

    • Pry the side of the SSD opposite the SSD tray socket out of the SSD tray.

    • Only lift the SSD up far enough to grab the sides of it with your fingers. Lifting it any more may damage the card or socket.

    Traducir

  16. MacBook Pro 13" Retina Display Early 2013 SSD Replacement: paso 15, imagen 1 de 2 MacBook Pro 13" Retina Display Early 2013 SSD Replacement: paso 15, imagen 2 de 2

    • Carefully pull the SSD straight out of its socket on the SSD tray.

    Traducir

  17. MacBook Pro 13" Retina Display Early 2013 SSD Replacement, SSD: paso 16, imagen 1 de 1

    • SSD remains.

    Traducir
Conclusión

To reassemble your device, follow these instructions in reverse order.

54 personas más completaron esta guía.

Autor

con 5 otros colaboradores

Sam Goldheart

Miembro Desde 10/18/12

465,656 Reputación

538 Guías creadas

Insignias: 48

+ 45 más insignias

Equipo

iFixit Miembro de iFixit

Staff

135 Miembros

16,732 Guías creadas

5 comentarios

Excelente, muchas gracias

Ruben Morales - Contestar

Ok, now that I replaced my SSD - how do I recover my OS?

Andy Stevko - Contestar

You can boot your mac to the recovery pressing command + R while you turn on your mac, configure your wifi and then create the partition in the ssd using disk utility, then you can clos disk utility and proceed to the instalation of the OS, the installation will be downloaded from the apple servers so it will depend of your internet speed how long will it take.

Ivan Roque -

Sieht so aus, als würde da eine ganz normale 2,5”-SSD reinpassen, wenn man den Einschub weglässt. Kann man das Kabel am MBP entfernen und ohne den Einschub benutzen?

Familienfreundlicher_Nutzer - Contestar

Geht leider nicht. Die neue NVMe m.2 SSD muss eine Übergangslösung haben. Leicht zu finden beim Internett. Das Übergang ist ein kleines Zeug das Mann braucht der Länge und Datei - Brikett zur passen.

Adrian Swift -

Agregar Comentario

Ver Estadísticas:

Ultimas 24 horas: 10

Ultimos 7 días: 87

Ultimos 30 días: 461

Todo El Tiempo: 139,943