Saltar al contenido principal

MacBook Pro 13 "Unibody Mid 2009 reemplazo del ventilador

Qué necesitas

  1. MacBook Pro 13 "Unibody Mid 2009 reemplazo del ventilador, Retira los tornillos de la tapa de abajo: paso 1, imagen 1 de 1
    • Retira los siguientes 10 tornillos que sujetan la tapa inferior del MacBook Pro 13 "Unibody:

    • Siete tornillos Phillips de 3 mm.

    • Tres tornillos Phillips de 13,5 mm.

    Compare the short screws carefully before reinstalling them. The shouldered screws go in the holes on the front edge.

    David Kilbridge - Contestar

    Before I started removing any screws I took a piece of paper and drew the bottom of the laptop and put a piece of double-sided tape in the spot where each screw goes. That way when I took out the screws, I could put them on the tape so I knew exactly which screw went in which spot. I did the same thing for dismantling the inside on another sheet of paper, then a third sheet for the screen after getting the front glass off.

    mastover - Contestar

    I use a similar technique: I print out the iFixit manual for the job, and Scotch-tape down the screws/brackets/cables I remove at each step next to the component descriptions. That way, when I'm reassembling, the bits are taped right next to the photo of where they came from.

    adlerpe -

    That's exactly what I do for all my repairs! It's the best way to keep track of all of the parts ' original location and to make sure that you don't miss any parts during reassembly.

    joyitsjennie -

    Great idea and one I use often

    Thomas Overstreet -

    Excellent idea! Thanks for sharing it here.

    Laura Sharkey -

    I used a 00 that fit but the screws were very tight so I used a tiny paintbrush with some wd40 on it and put it around the edges of the screws. Worked like a charm

    valentinedhdh - Contestar

    I use a magnetic mat and place the screws in order on that :)

    Cary B - Contestar

  2. MacBook Pro 13 "Unibody Mid 2009 reemplazo del ventilador, Levanta y retira la tapa de abajo: paso 2, imagen 1 de 1
    • Levanta ligeramente la tapa inferior y empuja hacia la parte posterior para liberarlo de las pestañas que lo sujetan

    In the introduction you should link fixers to this excellent doc: https://www.ifixit.com/Misc/HD_Software_...

    It is really critical, super easy, and free(!) to clone your existing drive onto the new one you will install. I ran into one error, but SuperDuper! support replied immediately on how to fix it...Thanks ifixit and SuperDuper! (I ponied up the $28 for the software anyway, I was so impressed!)

    Mike - Contestar

    Long story short: I drank the AppleKoolAid back in 1984 and have always left the guts of my machines up to Apple - until recently when I needed to swap the SATAs from my original MacDaddy (2009 13" MBPro that I killed in 2018 - coffee + blackout = OOOOPS) into a pristine 2009 MBPro from a Goodwill in North Carolina through eBay. I need the files from iCal and MacMail that can't be opened in my newer machines.

    Well . . . I ain't never done nuttin' like that, before!

    Enter Luke Miani on YouTube. He raves about you guys! So, I watched everything I could, read your site, bought the right tools and at the ripe old age of 72, I sat down, this morning and did the work. Now my original MacDaddy lives in MacDaddy2.0.

    Am I allowed to cry?

    Seriously, I can't thank you enough for your bitchen site and killer tools. I wish I'd'a been turned on to this shizzle 30+ years ago.

    IFIXIT - IDIGIT!

    kath myers - Contestar

    HAHAHAHAHAHAHAHAHAHA.

    That was a brilliant read.

    Yes, I came across ifixit a few years ago. Totally helped me out on several occasions.

    Glad your Mac repair journey worked out.

    :)

    Cary B -

  3. MacBook Pro 13 "Unibody Mid 2009 reemplazo del ventilador, Batería: paso 3, imagen 1 de 1
    • Por razones de precaución, le recomendamos que desconecte el conector de la batería de la placa lógica para evitar cualquier descarga eléctrica.

    • Utilice el extremo plano de un spudger para levantar el conector de la batería hacia arriba fuera de su toma en la placa lógica.

    Cita de gansodesoya:

    why is step 3 necessary?

    Just to disconnect any power source to avoid damages by short-circuits.

    MrKane - Contestar

    How do you get that battery connector back on? Do you just press it in back in place after you're done?

    Horace Chung - Contestar

    yes. I usually plug it in before I screw it down so I can lift the battery a bit and have enough slack to be able to go straight down on the connector, otherwise it comes in on a bit of an angle, which can't be good (though not necessarily bad).

    maccentric -

    This step almost finished me, and I did extensive damage to the battery plug. Fortunately, I later replaced the battery, and the replacement came with a new plug! :) Newbies need to know - 1. The battery plug is like a thin lip on a thicker lip, so you need to pry BETWEEN 2 thin lips to get it off, else you are trying to yank out the socket. 2. Mine was initially VERY tight, and trying to get it out broke the plastic on all sides of plug, even though I was as careful as possible. Luckily, this didn't hurt functionality and I later replaced the battery. AFTER disconnecting once, it was never so tight again,

    Jeff Diamond - Contestar

  4. MacBook Pro 13 "Unibody Mid 2009 reemplazo del ventilador, Ventilador: paso 4, imagen 1 de 3 MacBook Pro 13 "Unibody Mid 2009 reemplazo del ventilador, Ventilador: paso 4, imagen 2 de 3 MacBook Pro 13 "Unibody Mid 2009 reemplazo del ventilador, Ventilador: paso 4, imagen 3 de 3
    • Utilizar un spudger para sacar el conector del ventilador de su asiento, y hacia arriba de la placa lógica.

    • Es útil girar el spudger axialmente desde debajo de los cables del ventilador para liberar el conector.

    • El zócalo del ventilador y el conector del ventilador se pueden ver en la segunda y tercera imágenes. Tenga cuidado de no romper la toma de plástico del ventilador de la placa lógica mientras utiliza su spudger para levantar el conector del ventilador hacia arriba y fuera de su zócalo.

    • El diseño de la placa lógica que se muestra en la segunda imagen puede parecer ligeramente diferente de su máquina, pero la toma del ventilador es la misma.

    I just soldered it back on. . . I tried to clean the pads with braid first, but it didn't do much so I don't think that's necessary. I first supper-glued it in place with the pins on the pads and then I put a tiny dab of solder on each pin/pad. Plugged in the fan and i works!

    Ron Hudson - Contestar

    Just the answer I was looking for Ron! Awesome work buddy!

    lucasjmenzie -

    i recommend not to use the spudger. you damage more than by unpluggin the plug by hand. just simply pull the cable close to the plug of the old fan softly upwards out. the plug than comes easily out. put the new fan in and push the new plug by hand in. it is much easier than using a spudger. i also started with a spudger but nearly broke the plug out, so i watched a youtube tutorial and learned about it…

    andre - Contestar

  5. MacBook Pro 13 "Unibody Mid 2009 reemplazo del ventilador: paso 5, imagen 1 de 1
    • Retire los siguientes tres tornillos que sujetan el ventilador a la carcasa superior:

    • Un Phillips de 6.5 mm.

    • Un Phillips de 5.5 mm.

    • Un Phillips de 4.5 mm.

  6. MacBook Pro 13 "Unibody Mid 2009 reemplazo del ventilador: paso 6, imagen 1 de 1
    • Levante el ventilador de la caja superior.

Conclusión

Para volver a armar su aparato, siga estas instrucciones en orden inverso.

106 personas más completaron esta guía.

Un agradecimiento especial a estos traductores:

en es

100%

¡ irlanda nos está ayudando a reparar el mundo! ¿Quieres contribuir?
Empezar a traducir ›

3 comentarios

I upgraded my macbook pro 13" mid 2009:

replaced optical drive with 250GB SSD.

replaced 2x2GB RAM with 2x4GB.

replaced old battery..

Things work, except the fan never slows down and makes a lot of noise.

The fan start at full speed as soon as I click the power button, even before the screen lights up.

Please help.

Also the bluetooth and camera stopped working :(

abhi - Contestar

When I reapplied thermal paste to my heat sink ~18 month ago, I had issues reconnecting the camera cable (see Step 10 MacBook Pro 13 "Unibody Mid 2009 reemplazo del disipador de calor). All of the symptoms you described were exactly those I saw when my camera cable was not properly reconnected. Perhaps you should check here.

NicoleCLDay -

If you didn't get a thermal sensor for your ssd your Mac fan will run at full speed 24/7 until you get the sensor

Jake / -

Agregar Comentario

Ver Estadísticas:

Ultimas 24 horas: 1

Ultimos 7 días: 8

Ultimos 30 días: 45

Todo El Tiempo: 90,010