Esta versión puede contener ediciones incorrectas. Cambiar a la última instantánea verificada.
Qué necesitas
-
-
Utiliza una moneda o un spudger para girar el tornillo de bloqueo de la batería 90 grados en el sentido de las agujas del reloj.
-
-
-
Retira los tres tornillos Phillips espaciados uniformemente a lo largo de la pared posterior del compartimento de la batería.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the following 3 screws:
-
One 11 mm Phillips #00 in the middle of the case.
-
Two 14.5 mm Phillips #00.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the following 3 screws from the rear wall of the battery compartment:
-
Two 3 mm Phillips #00. (A1181 has three 3 mm screws and one 4 mm.)
-
One 4 mm Phillips #00 on the right side.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the two 6 mm Phillips #00 screws from either side of the right wall of the battery compartment (not the ones closest to the battery connector).
-
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the four 3 mm indicated Phillips #00 screws from the front wall of the battery compartment. When working from the left, remove the 2nd, 4th, 7th and 9th screw.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the following 4 screws from the back of the computer:
-
Two 7 mm shouldered Phillips on the far sides.
-
Two 10.5 mm Phillips toward the center.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the two 5.2 mm shouldered Phillips #00 screws from the optical side of the computer.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Starting near the display and working around to the front of the computer, pry up on the upper case. It is held with clips on the right above the optical drive. These will release with some firm lifting pressure.
-
Be careful when prying up the upper case. It's very easy to slice open a fingertip and thus provide the blood sacrifice the Mac gods sometimes require of those who insist on doing their own repairs.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
While holding up the upper case (from the bottom or the top), use a spudger to pry up the orange trackpad and keyboard cable from its connector.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Use the white plastic pull-tab to slide the hard drive to the left and out of the computer.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Disconnect the orange optical drive ribbon cable from the logic board.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Disconnect the newly-revealed display data cable. If there is no pull-tab on the top of the connector, it may be helpful to use a spudger to disconnect this connector.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Disconnect the (once again) newly-revealed hard drive cable.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Deroute the hard drive connector cable from the four tabs along the edge of the optical drive.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the two Phillips screws securing the hard drive connector to the lower case.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Carefully lift the hard drive connector out of the case slightly, and turn it over to reveal the IR sensor connector beneath. Use a spudger to flip up the tiny bar holding the cable in place.
-
Slide the orange IR sensor cable out of its connector, and lift the hard drive connector out of the computer.
-
Cancelar: No complete esta guía.
26 personas más completaron esta guía.