Esta versión puede contener ediciones incorrectas. Cambiar a la última instantánea verificada.
Qué necesitas
-
-
Utiliza una moneda o un spudger para girar el tornillo de bloqueo de la batería 90 grados en el sentido de las agujas del reloj.
-
-
-
Retira los tres tornillos Phillips espaciados uniformemente a lo largo de la pared posterior del compartimento de la batería.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the following 3 screws:
-
One 11 mm Phillips #00 in the middle of the case.
-
Two 14.5 mm Phillips #00.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the following 3 screws from the rear wall of the battery compartment:
-
Two 3 mm Phillips #00. (A1181 has three 3 mm screws and one 4 mm.)
-
One 4 mm Phillips #00 on the right side.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the two 6 mm Phillips #00 screws from either side of the right wall of the battery compartment (not the ones closest to the battery connector).
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the four 3 mm indicated Phillips #00 screws from the front wall of the battery compartment. When working from the left, remove the 2nd, 4th, 7th and 9th screw.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the following 4 screws from the back of the computer:
-
Two 7 mm shouldered Phillips on the far sides.
-
Two 10.5 mm Phillips toward the center.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the two 5.2 mm shouldered Phillips #00 screws from the optical side of the computer.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Starting near the display and working around to the front of the computer, pry up on the upper case. It is held with clips on the right above the optical drive. These will release with some firm lifting pressure.
-
Be careful when prying up the upper case. It's very easy to slice open a fingertip and thus provide the blood sacrifice the Mac gods sometimes require of those who insist on doing their own repairs.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
While holding up the upper case (from the bottom or the top), use a spudger to pry up the orange trackpad and keyboard cable from its connector.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Grasp the white plastic tab attached to the hard drive and pull it to the left, removing the hard drive from the computer.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the two Phillips screws from the front edge of the optical drive.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Disconnect the orange optical drive ribbon cable from the logic board.
-
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Disconnect the newly-revealed display data cable. If there is no pull-tab on the top of the connector, it may be helpful to use a spudger to disconnect this connector.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Disconnect the (once again) newly-revealed hard drive cable.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Peel up the foil tape between the fan and the optical drive.
-
Remove the 8.5 mm Phillips screw securing the display data cable to the metal framework.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Pull up the display data cable from along the edge of the optical drive to reveal a silver Phillips screw.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the 2.8 mm Phillips screw securing the optical drive.
-
After removing the screw, push the metal tab backwards, towards the fan, to release the front of the optical drive.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Lift the Bluetooth antenna board from the right side of the optical drive.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Deroute the hard drive cable from along the front of the optical drive.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Lift the front edge of the optical drive and slide it up and out of the computer.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the following 3 screws:
-
Two 3 mm Phillips near the right speaker.
-
One 6 mm Phillips threaded through a hole in a plastic finger above the subwoofer.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Lift the right speaker out of its housing and set it to the side.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Using a spudger, gently pry up the white plastic slot and slide the metal c-channel to the right and away from the display.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Use a spudger to carefully disconnect the microphone cable from the logic board. You'll want to work from side to side, and slowly wiggle the connector out of its socket.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Lift up on the black right speaker cable with one hand, and deroute the silver microphone cable from the silver metal clip just above the right RAM slot.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Deroute the silver microphone cable and gray display data cable from the tabs at the bottom of the subwoofer.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the single 3.2 mm Phillips screw securing the ground loop in the display data cable located just above the Bluetooth board.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Disconnect the two antenna cables from the Airport card, and the black inverter cable from the logic board. (Pull vertically on all three.)
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the following 2 screws from the right hinge mount:
-
One 6 mm Phillips on the left side of the hinge mount.
-
One 10 mm Phillips on the right side of the hinge mount.
-
Lift the right hinge mount out of the computer.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Hold the display with one hand while removing the screws from the left hinge mount.
-
Remove the following 3 screws from the left hinge mount:
-
One 6 mm smaller diameter Phillips from the right side.
-
One 6 mm larger diameter Phillips from the middle.
-
One 10 mm Phillips from the left side.
-
Lift the left hinge mount out of the computer.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Grasp the display assembly on either side, and lift it up and out of the computer.
-
-
Este paso está sin traducir. Ayuda a traducirlo
Herramienta utilizada en este paso:Plastic Cards$2.99-
Use a thin plastic card to release the tabs and their clips holding the front display bezel to the display assembly. There are five tabs along the left side of the display bezel.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Continue to free the tabs along the the top edge of the display assembly.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Next, free the five tabs securing the display bezel on the right side.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Lift up the front display bezel from the top and use your plastic card to free the tabs along the bottom edge of the display bezel.
-
After freeing all holding tabs, lift the front display bezel away from the display assembly.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Use a metal spudger or another thin tool to carefully pry the gray plastic clips off the tabs molded into the front display bezel. A 0.8mm flat screwdriver may be useful for this step. You may find that it's easier to remove some of these clips by prying up on their long sides.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Insert one end of the retaining clip beneath the edge of its recess cut into the LCD bracket.
-
Use the edge of a spudger to push the short hook tab on the underside of the other end of the retaining clip into the recess cut into the LCD bracket.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the three 4.2 mm Phillips screws securing the clutch cover.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
While holding the display down with one hand, use your other hand to lift the left end of the clutch cover off the clutch hinge and guide the inverter cable and AirPort cables through the gap in the clutch cover. If the cables snag on the two hooked tabs on the inside end of the clutch cover, free them carefully.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Lift up the right end of the clutch cover while guiding the display data and iSight cables through the gap and the two hooked tabs at the right end of the clutch cover. If the cables snag on the two hooked tabs, free them carefully.
-
Lift the clutch cover off of the display assembly.
-
Cancelar: No complete esta guía.
15 personas más completaron esta guía.
Un comentario
Excellent guide. Thank you.
I just wish I read it before stripping down my MacBook last night.
At least I know what screws go where when reassembling it with new hinges.