Saltar al contenido principal

Esta versión puede contener ediciones incorrectas. Cambiar a la última instantánea verificada.

Qué necesitas

  1. , Caja inferior: paso 1, imagen 1 de 1
    • Retira los siguientes 10 tornillos que sujetan la caja inferior de la Air:

    • Seis tornillos Phillips de 2.8 mm.

    • Dos tornillos Phillips de 3.8 mm.

    • Dos tornillos Phillips de 5.4 mm.

  2. : paso 2, imagen 1 de 2 : paso 2, imagen 2 de 2
    • Levanta ligeramente la caja inferior cerca de los orificios de ventilación y empújala hacia la parte posterior de la computadora para liberar las pestañas de montaje.

  3. , Bateria: paso 3, imagen 1 de 1
    • Desconecta el conector de la batería tirando de él directamente fuera de su zócalo.

  4. : paso 4, imagen 1 de 1
    • Retira los siguientes nueve tornillos que sujetan la batería a la Air:

    • Cuatro Phillips de 2.9 mm.

    • Cuatro Phillips de 3.8 mm.

    • Un Phillips de 7.2 mm.

  5. : paso 5, imagen 1 de 1
    • Saca la batería de la Air.

    • Si estás instalando una batería nueva, debes calibrarla luego de la instalación:

    • Cárgala hasta el 100% y luego sigue cargándola durante al menos 2 horas más. Luego, desenchúfala y úsala normalmente para drenar la batería. Cuando veas la advertencia de batería baja, guarda tu trabajo y mantén tu laptop encendida hasta que se duerma. Espera al menos 5 horas, luego cárgala de forma ininterrumpida hasta 100%.

    • Si notas alguna conducta o problema inusual luego de instalar tu batería nueva, podrías necesitar restablecer el SMC de tu MacBook Pro.

  6. , Disco duro: paso 6, imagen 1 de 3 , Disco duro: paso 6, imagen 2 de 3 , Disco duro: paso 6, imagen 3 de 3
    • Desconecta el cable plano de la escotilla del puerto de la placa lógica tirando de él hacia arriba por su lengüeta negra.

    • Retira el cable plano de salida de audio del adhesivo que lo sujeta a la carcasa superior.

    • Utiliza un spudger para hacer palanca en el conector del cable plano de salida de audio del soporte del disco duro.

    I skipped the step (6c) of prying the audio out ribbon cable connector board off the hard drive bracket (& disconnecting it), since it doesn't come off real easily, and I didn't want to damage it. It only requires a little more care when removing the HD from it's bracket if you skip step 6c.

    amiller770 - Contestar

  7. : paso 7, imagen 1 de 1
    • Desconecta el cable de salida de audio de su toma en el cable plano de la escotilla del puerto.

    This is not necessary and looks pretty risky too.

    eugene_o - Contestar

    Agreed, I encountered no issues when I skipped this on a Rev.B model.

    Kyle Milnes -

  8. : paso 8, imagen 1 de 1
    • Utiliza un punzón para levantar el conector del cable del disco duro de la placa lógica.

    Reversing step 8 is where I ran into trouble. The replacement fan I had was slightly thicker than the original and caused the ZIF cable to work its way out of the tenuous connection it had to the SSD, resulting in a "?" missing boot drive error upon startup. Took me three tries to get it right! The difficulty is to get the drive connector to the logic board to reach and seat without pulling the other end out of the drive.

    aaronmiller - Contestar

  9. : paso 9, imagen 1 de 2 : paso 9, imagen 2 de 2
    • Utiliza el extremo afilado de un spudger para desviar el cable del micrófono del soporte del disco duro.

    • Retira la tapa del tornillo cosmético del adhesivo que lo fija al soporte del disco duro.

  10. : paso 10, imagen 1 de 1
    • Retira los cuatro tornillos Phillips que fijan el conjunto del disco duro a la carcasa superior:

    • Dos tornillos de 4,7 mm.

    • Dos tornillos de 3,9 mm.

    Longer screws on top.

    Adam Nelson - Contestar

    Two 3.9 mm Phillips screws.

    Two 4.7 mm Phillips screws.

    Alvaro Hermida - Contestar

    There is a cable glued to the diskframe that must be loosened with a spudger before you can remove the frame.

    oysteinalsaker - Contestar

  11. : paso 11, imagen 1 de 1
    • Extrae el conjunto del disco duro de la carcasa superior.

    Ever since Steve Jobs died, Apple hasn't been what it used to be.

    George A. - Contestar

  12. Este paso está sin traducir. Ayuda a traducirlo

    : paso 12, imagen 1 de 1
    • Use the tip of a spudger to pull the fan cable connector straight away from its connector on the logic board.

  13. Este paso está sin traducir. Ayuda a traducirlo

    : paso 13, imagen 1 de 2 : paso 13, imagen 2 de 2
    • Use the tip of a spudger to move the cosmetic fan cover aside.

  14. Este paso está sin traducir. Ayuda a traducirlo

    : paso 14, imagen 1 de 2 : paso 14, imagen 2 de 2
    • If you have the original version of the MacBook Air (A1237), refer to picture 1. Remove the following screws securing the heat sink to the logic board:

    • One 5.9 mm Phillips screw.

    • Two 1.9 mm Phillips screws.

    • One 1.9 mm Phillips screw.

    • If you have the A1304 version of MacBook Air, refer to picture 2. Remove the following screws securing the heat sink to the logic board:

    • One 5.0 mm Phillips screw

    • Five 1.9 mm Philips screws.

    • One 2.5 mm Phillips screw.

    On A1237, the yellow screw is a bit longer then the two orange ones.

    Peterdk - Contestar

    I have replaced several Logic boards at this point on the A1304 model, and realized that I did not need to remove the heatsink (Steps 14 through 17). You need to remove the screws around the fan, and disconnect the microphone cable (step 19). Of course if your replacement logic board doesn't include a heatsink, you need to take it off.

    Steerpike - Contestar

  15. Este paso está sin traducir. Ayuda a traducirlo

    : paso 15, imagen 1 de 1
    • Lift the processor clamp off the heat sink.

  16. Este paso está sin traducir. Ayuda a traducirlo

    : paso 16, imagen 1 de 1
    • Deroute the microphone cable away from the channel in the fan.

  17. Este paso está sin traducir. Ayuda a traducirlo

    : paso 17, imagen 1 de 1
    • Lift the heat sink up off the logic board.

    • Be mindful of the microphone cable when lifting the heat sink, as it can get tangled on the top edge of the fan.

    • When you mount the heat sink back onto the logic board, be sure to apply a new layer of thermal paste. We have a guide that makes replacing the thermal paste easy.

    I removed the fan at this point as well. Disconnect the small connector from the fan to the logic board and lift out the fan. Good time to blow off the dust!

    Andrea Wang - Contestar

  18. Este paso está sin traducir. Ayuda a traducirlo

    : paso 18, imagen 1 de 1
    • Use a spudger to pry the audio cable connector up off the logic board.

  19. Este paso está sin traducir. Ayuda a traducirlo

    : paso 19, imagen 1 de 1
    • If present, remove the small piece of black tape covering the microphone cable connector.

    • Disconnect the microphone cable by pulling its connector straight away from the socket on the logic board.

  20. Este paso está sin traducir. Ayuda a traducirlo

    : paso 20, imagen 1 de 2 : paso 20, imagen 2 de 2
    • Remove the two small Phillips screws securing the logic board bracket to the upper case.

    • Lift the logic board bracket out of the upper case.

  21. Este paso está sin traducir. Ayuda a traducirlo

    : paso 21, imagen 1 de 2 : paso 21, imagen 2 de 2
    • Use a spudger to pry the AirPort/Bluetooth and trackpad control cable connectors up off the logic board.

  22. Este paso está sin traducir. Ayuda a traducirlo

    : paso 22, imagen 1 de 1
    • Disconnect the DC-In cable by pulling its connector straight away from the socket on the logic board.

  23. Este paso está sin traducir. Ayuda a traducirlo

    : paso 23, imagen 1 de 2 : paso 23, imagen 2 de 2
    • Remove the small Phillips screw securing the display data cable ground loop to the upper case.

    • Disconnect the display data cable by pulling its connector straight away from the socket on the logic board.

  24. Este paso está sin traducir. Ayuda a traducirlo

    : paso 24, imagen 1 de 1
    • Remove the three Phillips screws securing the logic board to the upper case.

  25. Este paso está sin traducir. Ayuda a traducirlo

    : paso 25, imagen 1 de 1
    • Lift the logic board out of the upper case.

Linea de Meta

57 personas más completaron esta guía.

5 comentarios

nice its very helpful for each other.

Rjames Tabuzo - Contestar

I currently have a 1.6ghz A1237 Original Macbook Air, and I was wondering if the logicboard is interchangeable with the late 2008 model A1304. I hope someone can answer this for me. I want to swap out the logic board for A1304.

ric2081263 - Contestar

I have the same question too. Who can help me because I want to upgrade to El Capitan instead of Lion

Tom Xu -

great work and helpful!

frank.haubold - Contestar

Can we upgrade or add, make part from new mac dumbed down? advisor meeting with your board

Donald Eugene Moore - Contestar

Agregar Comentario

Ver Estadísticas:

Ultimas 24 horas: 4

Ultimos 7 días: 18

Ultimos 30 días: 73

Todo El Tiempo: 134,733