Saltar al contenido principal

MacBook Air 13" Mid 2013 Ensamblaje Placa Lógica Reemplazp

Sólo Prerrequisito
Esta guía solo debería usarse como prerrequisito para otras guías. Por tanto, estará incompleta.

Qué necesitas

  1. MacBook Air 13" Mid 2013 Ensamblaje Placa Lógica Reemplazp, Ensamblaje de placa lógica: paso 1, imagen 1 de 2 MacBook Air 13" Mid 2013 Ensamblaje Placa Lógica Reemplazp, Ensamblaje de placa lógica: paso 1, imagen 2 de 2
    • Agarra la lengüeta plástica asida al seguro del cable de datos de la pantalla y muévela hacia la parte superior del computador.

  2. MacBook Air 13" Mid 2013 Ensamblaje Placa Lógica Reemplazp: paso 2, imagen 1 de 2 MacBook Air 13" Mid 2013 Ensamblaje Placa Lógica Reemplazp: paso 2, imagen 2 de 2
    • Tira del conector de cable de datos de la pantalla directamente del socket.

    • Asegúrate de tirar del conector de forma paralela a la placa lógica, no lo levantes hacia arriba.

  3. MacBook Air 13" Mid 2013 Ensamblaje Placa Lógica Reemplazp: paso 3, imagen 1 de 2 MacBook Air 13" Mid 2013 Ensamblaje Placa Lógica Reemplazp: paso 3, imagen 2 de 2
    • Usa el extremo plano del spudger para extraer ambos conectores del cable de la antena hacia arriba y fuera de sus sockets de la tarjeta AirPort/Bluetooth.

    One of my terminals is broken. What solutions do you recommend me

    Omar Lopez - Contestar

    You’re actually pushing the connector from side to side toward the front of the case (or towards the track pad). It’s not a vertical motion at all.

    Jay Quilty - Contestar

    I’d also mention to be careful taking these off and putting them back on. I also accidentally pulled a terminal off it’a cable.

    Jean-Pierre Bazinet - Contestar

    If the process is taken to replace the top case, you can leave the AirPort card hanging from the antenna wires. Only remove the card’s retaining screw and slide the card to the right (direction of the antenna connectors) to separate it from the main board.

    Yishai Sered - Contestar

  4. MacBook Air 13" Mid 2013 Ensamblaje Placa Lógica Reemplazp: paso 4, imagen 1 de 2 MacBook Air 13" Mid 2013 Ensamblaje Placa Lógica Reemplazp: paso 4, imagen 2 de 2
    • Desconecta el cable conector de la cámara con la punta del spudger.

    • Empuja primero de un lado del conector, luego del otro lado para "sacarlo" cuidadosamente del socket.

    • Tira del cable de la cámara paralelo a la superficie de la tarjeta I/O hacia el borde del Air para desconectarlo de su socket.

    • No levantes el cable mientras lo desconecta, puede que el socket puede romper la placa lógica.

    You’ve missed a whole section here on removing the fan. It’s still present in Step 19 pics, but gone by Step 23. It’s not that it’s difficult to work out how to do it. But, when reassembling and following the steps in reverse, it’s handy to know when to use which screws!

    Stuzzington Botulism - Contestar

    Ah! –my bad. The steps for removing Fan etc. are there –up round Step 13. It’s just your photos that are slightly out of sync, as it’s back in place again by Step 19. So, while working in reverse, it looks like it’s not been covered.

    Stuzzington Botulism - Contestar

    On getting it on — i feel it's implied by the word "push” you can walk it out with the spudger. I couldn't wanage that, and instead walked it out by taking the cord between my index and thumb and walking it out by pulling it to the right and then the left repeatedly in a

    Elijah Kennedy - Contestar

  5. MacBook Air 13" Mid 2013 Ensamblaje Placa Lógica Reemplazp: paso 5, imagen 1 de 2 MacBook Air 13" Mid 2013 Ensamblaje Placa Lógica Reemplazp: paso 5, imagen 2 de 2
    • Usa la punta de un spudger o su uña para levantar la solapa de retención del socket ZIF del cable plano del trackpad.

    • Asegúrate de que está levantando la aleta de retención con bisagras, no el socket en sí.

    • Tira el cable plano del trackpad hacia afuera del socket hacia el borde delantero del Air.

  6. MacBook Air 13" Mid 2013 Ensamblaje Placa Lógica Reemplazp: paso 6, imagen 1 de 3 MacBook Air 13" Mid 2013 Ensamblaje Placa Lógica Reemplazp: paso 6, imagen 2 de 3 MacBook Air 13" Mid 2013 Ensamblaje Placa Lógica Reemplazp: paso 6, imagen 3 de 3
    • Usa la punta del spudger para abrir la solapa de retención del socket ZIF del cable plano del teclado retroiluminado.

    • Asegúrate de que está levantando la aleta de retención con bisagras, no el socket en sí.

    • Usa el spudger para gentilmente retirar el cable plano del teclado retroiluminado fuera del socket.

    Do you know where i can buy the retaining clip ?

    Jo (MemePasGame) - Contestar

    Not sure you can. I’d just use some kapton tape to hold it in place and call it good.

    maccentric -

  7. MacBook Air 13" Mid 2013 Ensamblaje Placa Lógica Reemplazp: paso 7, imagen 1 de 1
    • Usa la parte plana del spudger para levantar el cable conector del parlante derecho fuera del socket de la placa lógica.

    • Es recomendable levantar por debajo de los cables.

    What is this cables for?

    great.ryankim - Contestar

    It’s a speaker cable

    maccentric -

    This is the one that gave me the hardest time!!! It does pop up and out tho.

    Edward Mills - Contestar

  8. MacBook Air 13" Mid 2013 Ensamblaje Placa Lógica Reemplazp: paso 8, imagen 1 de 1
    • Remuevw los seis tornillos 6.3 mm T5 Torx que sujetan la placa lógica a la carcasa superior.

    • En algunos modelos puede que los tornillos sean 4.1 mm T5 Torx.

    When re-assembling the motherboard, attach all 6 screws but do not completely tighten yet.

    First make sure the rubber gasket is sitting properly, that the 7th screw hole (from Step 18) is properly aligned, and the Airport wire is sitting properly and also not caught under the heat sink.

    Once everything is well aligned, start tightening the screws while watching out for the alignment. I found it useful to keep an eye on screw-hole from Step 18 as a reference.

    Rany - Contestar

    Going in this order, there is a 7th screw securing the logic board to the frame; the heatsink is secured to the logic board with 4 screws, and secured to the frame with 1 more screw. Either take the heatsink off first, or remove that last screw underneath two small black wires, next to the left (as viewed when using the computer; if the computer is flipped over with the cover off and the monitor hinge end of the computer farthest from you, it is in the far right corner) set of three big torx screws that hold the hinge in place. The exact location of this screw is pictured in step 35's second picture; the screw goes through the loop visible below the rubber fan insulator. Scoot those 2 li'l wires out of the way and remove that screw, then the logic board comes right out. If this isn't clear, please let me know and I'll try to describe it better, or add a photo. If I'm posting this to the wrong instruction page, let me know; I was pretty sure I correctly identified my rig, but if not, sorry for the N00bage.

    Fox MacLeod - Contestar

    I got an extra screw hiding under the rubber gasket holding the end of the heatsink to the chassis. Ended up bending the heatsink a little cause I wasn't looking for it.

    Corvallis Computer - Contestar

    In the model I was working on, the 6th screw (in the middle) was hiding under the Samsung RAM module. Simply remove the one T5 screw holding it in, slide the RAM module out, and the 6th screw will be exposed.

    Tim - Contestar

    “Samsung RAM module”… do you mean the SSD? That stick of NVRAM is totally your hard drive.

    FeRD - Contestar

    Exactly, he means SSD (storage) the RAM (memory) is soldered to this 820-00165 logic board. Also on this model the 2015 MBA there is no logic board retaining screw under the SSD

    Peter Newman -

  9. MacBook Air 13" Mid 2013 Ensamblaje Placa Lógica Reemplazp: paso 9, imagen 1 de 1
    • Remueve los dos tornillos interiores 4.9 mm T8 Torx que sujetan el retenedor del cable de la antena y la bisagra embrague izquierda a la parte superior de la carcasa.

    This is the same screws as step 17.

    Joseph Lee - Contestar

    In both the online and the PDF version, Steps 17-18 and Steps 29-30 are identical. At which stage should you actually remove the display screws?

    adlerpe - Contestar

    Good catch! We did some sleuthing and it looks like a couple guides did indeed have an extra section of steps! All better now =)

    Sam Goldheart - Contestar

    In my computer these screws were the same size as the other side’s hinge screws. All 6 are the same size.

    Yishai Sered - Contestar

  10. MacBook Air 13" Mid 2013 Ensamblaje Placa Lógica Reemplazp: paso 10, imagen 1 de 1
    • Empuja el retenedor del cable de la antena un poco y remueva los tornillos 3 mm T5 Torx que sujetan el disipador de calor de la parte superior de la carcasa.

    This step is not needed

    mayer - Contestar

    It’s not clear what you mean by “This step is not needed.” If you want to remove the logic board from the upper case in order to put it onto your replacement upper case, you will have to remove this screw.

    Richard Garella - Contestar

    This step is only needed if you’re replacing the ENTIRE top case. Simply swapping out the trackpad unit does not make this step necessary. This entire tutorial assumes you’re replacing the entire top case which is an expensive mistake if you’re simply replacing the trackpad and/or keyboard. The keyboard is removable as well despite those many tiny rivets. Save money and time by not replacing the entire top case for a bad trackpad and/or keyboard. I needed to accomplish this step because I also removed and replaced the keyboard.

    airshack - Contestar

    NOTE: There is a sort of clamp/washer attached to this screw that I didn’t know about until I flipped the laptop up on its side and it fell onto the desk. Also: you need to reset it *before* the motherboard

    Edward Mills - Contestar

    In my computer this screw was not there, nor was a related washer. I got it used so perhaps someone has already been there and did not replace the screw.

    Also, the photo here shows how this end of the fan gasket is placed

    .

    Yishai Sered - Contestar

  11. MacBook Air 13" Mid 2013 Ensamblaje Placa Lógica Reemplazp: paso 11, imagen 1 de 3 MacBook Air 13" Mid 2013 Ensamblaje Placa Lógica Reemplazp: paso 11, imagen 2 de 3 MacBook Air 13" Mid 2013 Ensamblaje Placa Lógica Reemplazp: paso 11, imagen 3 de 3
    • Desliza la parte plana del spudger por debajo del parlante derecho desde la parte más cercana a la bisagra hasta el borde frontal del Air para soltar el adhesivo.

    • Remueve el parlante derecho de la carcasa superior.

    You don’t really *have* to remove the speaker, especially if your replacement upper case assembly already includes the speakers.

    Alexander Zub - Contestar

    I found the same. If you already have speakers in your new upper case, you can leave them. When you put the logic board back in, it will be a tight fit. I had to start with the corner near the right hinge (the Thunderbolt port corner) and work it in to place.

    Richard Garella - Contestar

    If your keyboard and/or trackpad need replacing you do not have to replace the entire top case.

    airshack - Contestar

    If it is difficult to remove the speakers you can use Isopropyl Alcohol to loosen the adhesive holding the speakers in place. Make sure to keep the Isopropyl Alcohol away from the speaker itself.

    BluRepairs - Contestar

  12. MacBook Air 13" Mid 2013 Ensamblaje Placa Lógica Reemplazp: paso 12, imagen 1 de 2 MacBook Air 13" Mid 2013 Ensamblaje Placa Lógica Reemplazp: paso 12, imagen 2 de 2
    • Cuidadosamente remueve la placa lógica de la carcasa superior, teniendo en cuenta cualquier cable que pueda quedar atrapado.

    • Durante el armado:

    • Mantén los cables sueltos alejados de la placa así no quedaran atrapados debajo de esta.

    • Asegúrate que los cables de la antena estén en sus respectivas muescas, como se resalta en la segunda imagen.

    It’s probably worth mentioning here that during reassembly you want to tuck the rubber gasket under the extension of the heat sink that the fan slots into.

    David Bonner - Contestar

Conclusión

Para reensamblar tu dispositivo, sigue estas instrucciones en orden inverso

Una persona más ha completado esta guía.

Un agradecimiento especial a estos traductores:

en es

100%

Estos traductores nos están ayudando a reparar el mundo! ¿Quieres contribuir?
Empezar a traducir ›

0 comentarios

Agregar Comentario

Ver Estadísticas:

Ultimas 24 horas: 0

Ultimos 7 días: 0

Ultimos 30 días: 0

Todo El Tiempo: 317