Saltar al contenido principal

Partes

No se especificaron partes.

  1. Este paso está sin traducir. Ayuda a traducirlo

    Power down your Mac mini, disconnect all of the cables, and flip it over. Insert the Jimmy into the crack between the aluminum top housing and the plastic lower housing.
    • Power down your Mac mini, disconnect all of the cables, and flip it over.

    • Insert the Jimmy into the crack between the aluminum top housing and the plastic lower housing.

    • The Jimmy should reach a stop about 3/8" down.

  2. Este paso está sin traducir. Ayuda a traducirlo

    Gently bend the Jimmy outwards to pry the crack open a little larger and lift the lower housing up a small amount. There are several plastic clips on the lower housing that fit into a channel in the aluminum top housing. Your goal is to use the Jimmy to push these clips inward enough to free them from the channel, while gently pulling up on the lower housing. There are several plastic clips on the lower housing that fit into a channel in the aluminum top housing. Your goal is to use the Jimmy to push these clips inward enough to free them from the channel, while gently pulling up on the lower housing.
    • Gently bend the Jimmy outwards to pry the crack open a little larger and lift the lower housing up a small amount.

    • There are several plastic clips on the lower housing that fit into a channel in the aluminum top housing. Your goal is to use the Jimmy to push these clips inward enough to free them from the channel, while gently pulling up on the lower housing.

  3. Este paso está sin traducir. Ayuda a traducirlo

    Once you have the first side free, rotate the Mac mini and start prying up on the front edge. Use the same prying motion to both bend the clips inward and lift the lower housing up out of the top housing.
    • Once you have the first side free, rotate the Mac mini and start prying up on the front edge.

    • Use the same prying motion to both bend the clips inward and lift the lower housing up out of the top housing.

  4. Este paso está sin traducir. Ayuda a traducirlo

    You may need to move the Jimmy along the edge to pry up all of the clips. Be patient and do a little bit at a time. You may need to move the Jimmy along the edge to pry up all of the clips. Be patient and do a little bit at a time.
    • You may need to move the Jimmy along the edge to pry up all of the clips. Be patient and do a little bit at a time.

  5. Este paso está sin traducir. Ayuda a traducirlo

    Keep working around the perimeter, freeing the clips along the final edge. Keep working around the perimeter, freeing the clips along the final edge.
    • Keep working around the perimeter, freeing the clips along the final edge.

  6. Este paso está sin traducir. Ayuda a traducirlo

    Flip the Mac mini back over and lift the top housing off of the lower housing. Flip the Mac mini back over and lift the top housing off of the lower housing.
    • Flip the Mac mini back over and lift the top housing off of the lower housing.

  7. Este paso está sin traducir. Ayuda a traducirlo

    Remove the single Phillips screw between the headphone and microphone jacks on the audio board.
    • Remove the single Phillips screw between the headphone and microphone jacks on the audio board.

  8. Este paso está sin traducir. Ayuda a traducirlo

    Use the flat end of a spudger to pry the audio ribbon cable connector off the interconnect board.
    • Use the flat end of a spudger to pry the audio ribbon cable connector off the interconnect board.

  9. Este paso está sin traducir. Ayuda a traducirlo

    Use the tip of a spudger to depress the audio board retaining clip (shown in red) to release the audio board from the bottom housing. Lift the audio board from its free end and remove it from the mini.
    • Use the tip of a spudger to depress the audio board retaining clip (shown in red) to release the audio board from the bottom housing.

    • Lift the audio board from its free end and remove it from the mini.

    • Don't forget to transfer the audio ribbon cable to your new audio board.

Linea de Meta

4 personas más completaron esta guía.

0 comentarios

Agregar Comentario

Ver Estadísticas:

Ultimas 24 horas: 0

Ultimos 7 días: 2

Ultimos 30 días: 18

Todo El Tiempo: 16,646