Saltar al contenido principal

Reemplazo del Disco Duro de un Mac Mini Mid 2010

Sólo Prerrequisito
Esta guía solo debería usarse como prerrequisito para otras guías. Por tanto, estará incompleta.

Qué necesitas

  1. Reemplazo del Disco Duro de un Mac Mini Mid 2010, Disco Duro: paso 1, imagen 1 de 1
    • Quita los siguentes tres tornillos

    • Un tornillo Hexagonal T8 Torx de 5.0 mm o de 2.0 mm (cualquiera fucionará)

    • Un tornillo T8 Torx de 16.2 mm

    • Un tornillo de separación T6 Torx de 26 mm

    • Nota: Este tornillo de separación pudo haber sido removido con el ventilador.

    On mine I needed to remove the 26 mm T6 Torx standoff during step 3

    philipashlock - Contestar

  2. Reemplazo del Disco Duro de un Mac Mini Mid 2010: paso 2, imagen 1 de 2 Reemplazo del Disco Duro de un Mac Mini Mid 2010: paso 2, imagen 2 de 2
    • Con cuidado jala ambos cables de los sensores térmicos del disco duro hacia arriba para levantar sus conectores de su respectivo socket en la tarjeta lógica.

    BEWARE! Gently pulling one thermal sensor wire up from its logic board connector caused wire to rip loose from connector, leaving connector still in logic board socket. Using spudger on other connector caused same result. Even after wires ripped lose, it was impossible to get connector out of logic board socket (using spudger and needle nose pliers the connector came away in pieces). Connectors almost seem glued/fused into sockets and the wires will apparently break lose before the connector will release. What a terrible design. Here's hoping the mini will run without HDD thermal sensors :( I am experienced with repairing laptops and am kind of ticked because I am sure this damage was not due to incorrect/rough handling during attempt to disassemble.

    emcnally - Contestar

    Followup Note: Ending up with disconnected HDD thermal sensors due to breakage apparently causes the main system fan to run at full speed all the time. This is extremely loud and pretty much defeats the purpose of the Mini form factor. Going to have to try to rig something up with actual solder or adhesive tape.

    This is just stupid. A computer where logic board connections get broken while replacing a frickin HDD. All in an attempt to do something about the pathetic and feeble hard disk the vendor includes with their crap hardware (50MB/s transfer--what is this 1998?). Last Mac Mini I will ever buy. Slow, yet expensive and fragile.

    emcnally -

    Not sure what emcnally is talking about but mine came off fine. I have a 2010 mac mini and just upgraded to a 500 gig WD drive. Everything worked went great and was easier than I thought. My connectors pulled right off with no damage.

    Dave - Contestar

    tell the people to remove the superdrive’s thermal sensor as well! i just broke mine.

    Simon Meisinger - Contestar

    WARNING! Remove superdrive thermal sensor as well from the connector, or it will break in step 16.

    Laszlo Nyirfa - Contestar

    The plastic part broke for me. Barely putting any pressure on the connector and the thin plastic covering the metal connectors broke and the wires came out leaving the plastic connector in place. I was able to get the connector out without any more damage. Can I purchase a new thermal connector for this? I can't find the part listed anywhere.

    In the meantime I'm going to try and get the wires rigged to the board some how. Super glue them to the connector maybe. But I'm not sure if there is a polarity concern. Can the wires go to either pin on the board?

    Darrel Tenter - Contestar

    I was able to get the plastic connector back in place, and fit the wires into it. Polarity is needed. First time I got the fan running full. Switched the wires and now I think the fan is running normally.

    But I don't trust this connection over and time would like to find a replacement hard drive thermal sensor wire assembly.

    Darrel Tenter -

    Each of the hard drive temperature cable connectors have tiny little tabs on the sides. I found success using a small needle to carefully push under and pop the tab out.

    Leon Roy - Contestar

    Thanks, that's a nice way, works really well for me. Just try to stick a needle on the side and lift it up, if it has come up a little you can gently pull the cable and it will come off with very little force on the cable.

    gertjan -

    These connectors are fairly easy to unplug. You can pull up on the wires GENTLY to remove them. I used a wooden spudger to pry gently and the connectors popped right out. Putting them back in is easy just make sure they are right side up and they snap right back in.

    info - Contestar

    This is where I got in trouble too. No problems on the first of my Minis, but this time one of these sockets had poor soldering and just came off the board. Basically no solder connection to the posts that are there to hold the socket in place. I ended up using a pin to pry the rest of them off, in case the others were also poorly connected. The outside of the socket is U shaped, with 2 small tabs at the lower end of the U. I inserted a pin next to these tabs and it let me lever the connectors out easily. Now I get to practice my soldering!

    moecastleton - Contestar

    I used a pick (like a fine ice pick - available at Harbor Freight) to pry up the plastic clips while gently pulling at the wires with tweezers. They pull straight up. There are tiny tabs on the sides that kind of lock them in. I would not try just pulling on the wires. Everything is tiny and yrying to fix wires pulled out of the connectors would be very difficult.

    Steve Dollar - Contestar

    The pin method is definitely better. I used the pin to slightly spread the "wings" of the connector on the board. Then I levered out the part that is attached to the wires. All done with the aid of a magnifying loop.

    Fred Cat - Contestar

    I broke mine as well, did not replace the thermal sensor for the HDD, fan runs at full speed and is noisy. Went ahead and downloaded software fan control to reduce fan speed.

    Harish Ananthakrishnan - Contestar

    With all the good comments above, I was extra cautious, my two connectors have solid black covers and I couldn’t find the tabs for the needles. So I read ahead a few steps. I was able to skip this step 13 and steps 15 and 16 and take out the drive without force. Step 14 worked as described. I have a mid-2010 without an optical drive so there was only a hard drive connector.

    jstraath - Contestar

    Hi, i just used the flat end of ifixit’s plastic spudger to lift the tiny connectors without any tugging on the wires. First, i was a trained auto mechanic for 10 years then i got my electrical engineering degree! Started fixing macs in 1979 with an oscope, soldering iron and the ic circuit handbook plus chips from apple.

    Apples construction methods have sure gotten more and more fragile over the years. Glad i still have great eyes! Rossmon

    Ross Elkins - Contestar

    Thanks for the wonderful story, incredibly helpful to anyone reading it. A definite must for those upgrading their Minis. Perhaps an autobiography is in store for the future? I can only hope… I'd die knowing my life was complete if Im lucky enough to read such an intriguing story. OMG, and if it was hard back, I'd pass it down to the generations succeeding me so they too will grace this life changing experience. BRAVO to you sir !??

    AJ GREEN -

    I broke the connector too, but was able to make a secure connection despite this. You will need a good magnifier glass/visor and fine tweezers. I added a drop of Crazy glue to secure it. Photo: https://ibb.co/ZcsnvNC

    Gustavo Delfino - Contestar

    After the plastic of the connector of the thermal sensor falls in tiny little parts after manipulating with pludger, tweezers and all I can find in my home I just let the connector in place on the logic board. Like written down in step 15 and 16 I pulled the whole logic board just a little bit out of the housing, so there’s just enough room for pulling the old HDD out of the housing. Put away the different adhesive tapes HDD (main connector and thermal sensor). Put away main connector and the thermal sensor from the HDD. Then I put everything in place to the new SSD and stick the thermal connector with the the old adhesive stribe at the SSD. I never would try to disconnect the thermal sensor again from the logic board!!!

    Hanjo Lindenthal - Contestar

    I highly recommend TG Pro to solve this absurd hard disk temperature problem. After replacing my HDD with an SSD, the fan ran nutso just like everyone else’s. Sensors are in place on the drive, but they don’t seem to work. I even tried thermal paste, but no luck. While I could try replacing the temperature sensors, what’s the point? Having a quality SSD should remain far cooler than any HDD, regardless of the conditions.

    My Samsung EVO SSD has its own internal SMART temperature sensor built into it. TG Pro detects it fine. The reason I recommend TG Pro is that I tried others. TG Pro is top-of-the-line quality, imo. It even allows total override of system fan control, solving the runaway fan problem once and for all. While this is hypothetically a safety issue, since I began using the software 3 years ago, I’ve come to trust it more than whatever is built into my Macs. (I own three MacBooks in addition to my Mac Mini.)

    My 2010 is considered out of date, but with an SSD, it’s still a great little music server.

    AnnoniMoose - Contestar

    Found a 4,1 for $20, and flew too close to the sun. Thermal connections falling off everywhere. Will TG Pro (or something similar) allow me to just ignore replacing the HD sensors and the OD sensor?

    Clay Hummer - Contestar

    I wanted to change the Superdrive on a 2010 Mac mini and when I took off the thermal connector from the hard drive, one of the two cables came off.

    The hard drive has 2, it is the one on the other side of the SATA connector.

    If you don't connect that cable, the fan always starts at 5000rpm. It is Apple Part Number: 076-1369

    I was looking on Ebay/Ali and the cable is for €9, luckily you can insert the cable back into the connector and put a drop of thermal silicone to apply force and so far it works ok.

    morrit - Contestar

  3. Reemplazo del Disco Duro de un Mac Mini Mid 2010: paso 3, imagen 1 de 2 Reemplazo del Disco Duro de un Mac Mini Mid 2010: paso 3, imagen 2 de 2
    • Usa el extremo plano del spudger para hacer palanca en los conectores del disco duro y de la unidad óptica de sus sockets en la tarjeta lógica.

    I skipped this step as well as step 15 and 16.

    What I did, was just wiggle the drive out of the pc. Just pull it a little bit up and towards. Might need a little bit of force. But it should come out. Then, just remove the tape from the sata connector and then remove the sata connector from the hdd. Then you can replace the hdd like mentioned in this tutorial.

    And I removed only the left thermal sensor. The right one can stay on unless you need more room.

    gertjan - Contestar

  4. Reemplazo del Disco Duro de un Mac Mini Mid 2010: paso 4, imagen 1 de 3 Reemplazo del Disco Duro de un Mac Mini Mid 2010: paso 4, imagen 2 de 3 Reemplazo del Disco Duro de un Mac Mini Mid 2010: paso 4, imagen 3 de 3
    • Para tener suficiente espacio para remover el disco duro, la tarjeta lógica debe estar ligeramente fuera de su lugar. Para conseguir esto dos varillas cilíndricas deben ser insertadas en los agujeros remarcados en rojo.

    • Insertar instrumentos en cualquier agujero de la tarjeta lógica que no sea los que están remarcados en rojo puede dañarseveramente la tarjeta lógica.

    • Inserte una herramienta Mac mIni para remover la tarjeta lógica en los dos agujeros remarcados en rojo. Asegúrese que hace contacto con la carcasa exterior debajo de la tarjeta lógica antes de proceder.

    • Si no tiene una herramienta Mac mini para remover la tarjeta lógica a mano, puedes usar dos herramientas que tengan un máximo de 2.5 mm de diámetro. Solo inserta una en cada agujero remarcado.

    • Con cuidado jala la herramienta hacia la tarjeta I/O. La tarjeta lógica y el conjunto de la tarjeta I/O deben salir ligeramente de la carcasa exterior.

    • Deja de hacer palanca cuando la tarjeta I/O este visiblemente separada de la carcasa exterior. Remueve la herramienta Mac mini para remover la tarjeta.

    One MASSIVE hint to do this step: DON'T pull the tools towards you; rather, lever the top ends of the tools towards you, at and angle (so that the bottom of the tools don't move). Took me a while to figure this out!

    jon jon - Contestar

    Didn't have that special tool. Used iPhone repairset screwdriver. Worked fine with sticking it in to the holes verticaly and then push it towards me a bit, then changing holes and repeating that step.

    Alexander Kogler - Contestar

    I suggest to pull the wires for the cd drive thermal sensor and and the infrared sensor upward to lift their connectors up and out of their respective sockets on the logic board ((highlighted in red in the third picture of step 16).

    Riccardo Zulian - Contestar

    Two 3/32" drill bits work great at replacing the tool. Place the shaft of the bits into the holes.

    iceman - Contestar

    I had to watch a youtube video to see how this works. Then I realized you are just using the tools to pull the main board out toward the back of the mini.

    info - Contestar

    A couple of small screw drivers will do. Just make sure they go far enough into the hole to be able to lever against the bottom as you pull them towards you. Without this I started to damage the logic board slightly.

    David Jackson - Contestar

    How much pressure is necessary? Is it hard? Mine seams stuck.

    douglaslondrina - Contestar

    Sliding the motherboard forward is not really needed to remove the hard drive, but it sure makes it a bit smoother. Just need to persuade it to go over the memory bracket.

    Lying Bastard - Contestar

    NO NEED to slide the board out if there is already a 7mm thick SSD installed, as it comes out easily. Also don’t need to unplug the DVD SATA connector if not sliding the board out (Rt most SATA), or unplug the DVD heat thermal sensor, since you’re not moving the board. The less you unplug, the less chances of breaking a connector. However, with original or any 9mm HD, lifting it over the memory bracket would be very difficult IMO, w/o moving the board out ~5mm.

    amiller770 - Contestar

    I did NOT move the logic board. The original hard disk could be taken out with a little(!) force. The new replacement SSD was much thinner and was not problem to slide in.

    Christof Dallermassl - Contestar

    I used two thin screwdrivers. As they said, put them stright down the holes, and they seem to fit into something on the back side that holds the ends in place (eg. a shallow hole) in the top case or something).

    Then lean them both towards the back of the Mac (towards the ports etc.), and you’ll push the logic board AND the black part of the case, finally popping the black ports/rear free from the aluminum. Only needs to slide ~5mm as they said to get the needed clearance.

    Demis John - Contestar

    I tried so hard to just pry it out a short way, but so much force was needed that I ended up bring it out almost 1cm (ie the clips of the black rear ports fascia popped out of their recesses). This yanked the wires out of the optical drive thermal sensor. I was able to reinsert them with tweezers and hopefully the contact will be good enough to carry the signal. Wish I’d spudged that thermal sensor off the board when I was doing the other two (Step 10). After reading the warnings in step 10, I thought I didn’t need to worry about that until step 16.

    Andrew Boden - Contestar

  5. Reemplazo del Disco Duro de un Mac Mini Mid 2010: paso 5, imagen 1 de 3 Reemplazo del Disco Duro de un Mac Mini Mid 2010: paso 5, imagen 2 de 3 Reemplazo del Disco Duro de un Mac Mini Mid 2010: paso 5, imagen 3 de 3
    • Simultáneamente presione los dos clips de plástico al extremo izquierdo y derecho de la tarjeta I/O hacia el centro de la tarjeta I/O y jale la tarjeta I/O ligeramente de la carcasa externa.

    • Jala la tarjeta I/O y el conjunto de tarjeta lógica fuera de la carcasa exterior un mínimo de 5 mm. Jalando el conjunto mas lejos puede dañar el conector del sensor IR (remarcado en rojo en la tercer imagen).

    I found that when removing the logic board out a bit that the IR sensor was not so much of a problem as was the HDD temperature sensor located next to the IR sensor.

    My logic board accidentally popped out rather quickly and pulled out the sensor for the HDD.

    I don't know why it's not mentioned in the earlier step to just use the spudger to pop this cable off. Since it is mentioned in other guides for removal when replacing other parts.

    This would have been really helpful and most likely I would not have been left with loose cables and now looking for a new sensor cable.

    So fo any others out there replacing/upgrading your HDD and have some what of a hard time getting the logic board to budge just a bit, use the spudger to pop the cable off, it's not hard and pops back on as easily as the others. That's just an FYI and a preventative measure.

    tdowse1 - Contestar

    Ifixit note, Mac mini mid-2010 step 16

    @tdowse1 I agree completely. I take issue with this guide because I believe it has an error. With just one of two changes I wouldn't have destroyed my ZIF sensor connectors:

    1) Issue the warning BEFORE or even with the instruction. Following the instructions step by step and not reading a step ahead, you don't realize you can damage your cable irretrievably. Even if you read the entire guide first, you can't be expected to memorize all warnings BEFORE you act on the instructions.

    2) Instruct the user to disconnect ALL of the ZIF cables first. This is truly the only safe thing to do.

    LelandHendrix - Contestar

  6. Reemplazo del Disco Duro de un Mac Mini Mid 2010: paso 6, imagen 1 de 2 Reemplazo del Disco Duro de un Mac Mini Mid 2010: paso 6, imagen 2 de 2
    • Levanta el disco duro del borde mas cercano a la tarjeta lógica y remuévelo de la mini, teniendo en cuenta el socket de la RAM y algún cable que pueda ser atrapado.

    • Cuando reinstales el disco duro, asegúrate que las dos terminales T8 Torx en su extremo lejano estén insertados en los dos soportes de goma remarcados en rojo en la segunda foto, antes de deslizar la tarjeta lógica de vuelta en su lugar.

    The new drive, being thinner than the old one, was a bit tricky to get seated into the rubber grommets. I found that temporarily screwing a couple of screws into the top mounting holes on the drive helped with getting a grip on it. This, and standing the unit up on its end so that the drive would "fall" into the rubber grommets, worked OK for me.

    Fred Cat - Contestar

    Great tip @ Fred Cat!!

    Vevek Lochub - Contestar

Conclusión

Para volver a montar su dispositivo, siga las instrucciones en orden inverso.

Un agradecimiento especial a estos traductores:

en es

100%

Estos traductores nos están ayudando a reparar el mundo! ¿Quieres contribuir?
Empezar a traducir ›

0 comentarios

Agregar Comentario

Ver Estadísticas:

Ultimas 24 horas: 0

Ultimos 7 días: 0

Ultimos 30 días: 0

Todo El Tiempo: 1,944