Saltar al contenido principal

Reemplazo de ventilador en Mac Mini Mid 2010

Qué necesitas

  1. Reemplazo de ventilador en Mac Mini Mid 2010, Cubierta inferior: paso 1, imagen 1 de 2 Reemplazo de ventilador en Mac Mini Mid 2010, Cubierta inferior: paso 1, imagen 2 de 2
    • Coloca tus pulgares en los huecos en la cubierta inferior.

    • Rota la cubierta interior en sentido horario hasta que el punto blanco pintado en la cubierta inferior este alineado con el aro grabado en la cubierta exterior.

  2. Reemplazo de ventilador en Mac Mini Mid 2010: paso 2, imagen 1 de 1
    • Inclina el mini lo suficiente para permitir la cubierta inferior salir de la cubierta exterior.

    • Remueve la cubierta inferior y colócala a un lado.

  3. Reemplazo de ventilador en Mac Mini Mid 2010, Ventilador: paso 3, imagen 1 de 1
    • Remueve los dos tornillos T6 Torx de 11.3 mm que aseguran el ventilador a la tarjeta lógica cerca de la placa de la antena.

    There are actually 3 T6 screws securing the fan. The third screw is out of the screenshot, just below the RAM.

    inferno10 - Contestar

    Nope, that third screw is actually just a post that the rubber grommet attached to the fan body slips over. Step 4 shows how the fan comes off of it. When you go to remove the fan, you simply remove the two screws closest to the antenna plate and then lift the fan off this post. The screw you are talking about is removed in Step 14 and does not need to be removed until this point.

    Andrew Bookholt -

    Successful install completed, but I had some trouble getting the fan reinstalled. When I removed the fan from the "Step 14" post, the rubber piece stayed on the post. When attempting to reinstall the fan, it was impossible to get the loop to go back over that rubber piece. So, I had to remove the post (again), and with the help of the spudger and some patience, worked it through. Then installed the fan using the 2 screws and the post. I think it may have saved some time and trouble if I just removed all 3 in the first place, leaving the post in the fan.

    meag -

    On mine I needed to remove the 26 mm T6 Torx standoff during this step rather than step 12

    philipashlock - Contestar

    on my mid-2011 mac mini, that 3rd T6 post/screw had to be removed to get the fan out. It goes right through a hole in the fan housing. No way the grommet is slipping over anything without wreaking major havoc.

    Derek Shaw - Contestar

    On my mid-2010 mac mini, also removed the 26 mm T6 Torx standoff during this step instead of step 12. Having completed the steps, it appears my hard drive is from mid 2011, so maybe the production line for mine had changed.

    jstraath - Contestar

  4. Reemplazo de ventilador en Mac Mini Mid 2010: paso 4, imagen 1 de 1
    • Levanta la oreja del ventilador mas cercana a la RAM hasta el punto muerto fijado a la cubierta exterior.

    • Si el ventilador no se separa del tornillo de separación con una moderada cantidad de fuerza, puede usar un desarmador T6 Torx para simplemente remover el tornillo.

    Pulling on the ear didn't do anything, so I removed the whole screw at this step. The screw stayed fixed on the fan and I didn't have to remove it at the step where you remove the logic board screws.

    Probably I didn't want to use too much force .. but it worked

    Alexander Kogler - Contestar

    This is the approach I used. no way was the "ear" pulling over the head of the standoff without breaking something. The standoff simply unscrewed from whatever is under the logic board and stayed with the fan assembly. WAY safe

    Derek Shaw -

    Loosen the fan standoff from the motherboard using a T6 driver.

    bobcloninger - Contestar

    When I pulled the fan ear off the standoff the rubber grommet stayed on the standoff. That's fine, but it makes it difficult to put the fan ear back on during reassembly. So I just pulled the rubber grommet off the standoff and put it into the hole in the fan ear. Then I was able to push the fan ear onto the standoff with out trouble during reassembly.

    Dave Hein - Contestar

  5. Reemplazo de ventilador en Mac Mini Mid 2010: paso 5, imagen 1 de 1
    • Levanta el ventilador de la mini para que haya suficiente espacio para acceder a su conector.

    • Con cuidado jala los cables del ventilador hacia arriba para levantar el conector del ventilador de su zócalo en la tarjeta lógica.

    • Remueve el ventilador.

    Be careful here, this is not a simple action. Pulling on the wires risks them coming out of the sockets of the connector that attaches to the pins on the board. I had to use an Xacto knife to push on the end of the connector to push it off the pins rather than pull.

    Brian - Contestar

    Actually, just sliding a spudger under the wires and edging upwards is the easiest way to disconnect this connector - and most others, too.

    Aleks Gekht -

Conclusión

Para reensamblar tu dispositivo, sigue estas instrucciones en orden inverso.

23 personas más completaron esta guía.

Un agradecimiento especial a estos traductores:

en es

100%

Estos traductores nos están ayudando a reparar el mundo! ¿Quieres contribuir?
Empezar a traducir ›

2 comentarios

How do you know the order of the wires when placing the 4 wires back onto the motherboard?

Communications Department - Contestar

The connector is a snap in / snap out or more properly lift out connector. The connector goes back in only one way with the 4 pins aimed towards the wifi icon. To get it out you GENTLY lift the wires. I used my fingernail under the wires as they went from the fan into the connector.

Mike Stark - Contestar

Agregar Comentario

Ver Estadísticas:

Ultimas 24 horas: 2

Ultimos 7 días: 8

Ultimos 30 días: 35

Todo El Tiempo: 15,955