Saltar al contenido principal

Esta traducción podría no reflejar los cambios más recientes añadidos a la guía de referencia. Ayúdanos a actualizar la traducción o revisa la guía original.

Mac Mini Late 2014 reemplazo del ventilador

Sólo Prerrequisito
Esta guía solo debería usarse como prerrequisito para otras guías. Por tanto, estará incompleta.

Qué necesitas

  1. Mac Mini Late 2014 reemplazo del ventilador, Ensamblaje del ventilador: paso 1, imagen 1 de 1
    • Retira los dos tornillos T6 de 12 mm del ventilador.

    • Afloja el tornillo cautivo T6 de 27 mm.

    That 27mm screw should be very loose, since it attaches the motherboard to the case. When you’re trying to remove the motherboard, if the AC connection side of the board is not moving back easily, you need to make sure this screw is fully backed out from the case.

    There’s no danger in removing it completely.

    marklfarley - Contestar

    I suggest removing the 27 mm tool, otherwise Step 23 will not work.

    Arvin Bhatnagar - Contestar

    Actually you don’t need to remove 27mm from the fan. I was able to tilt a little when I take the logic board out in Step 23. I also didn’t take the fan cable too. When you pull the logic board out, put the fan on the back of logic board as you pull it out.

    Kenneth Z - Contestar

  2. Mac Mini Late 2014 reemplazo del ventilador: paso 2, imagen 1 de 3 Mac Mini Late 2014 reemplazo del ventilador: paso 2, imagen 2 de 3 Mac Mini Late 2014 reemplazo del ventilador: paso 2, imagen 3 de 3
    • El conector del ventilador está atrapado debajo del borde del ventilador y no se puede desconectar hasta que se mueva el ventilador.

    • No intentes quitar el ventilador por completo.

    • Levanta el ventilador hacia arriba para liberar el tornillo cautivo de su orificio en la placa lógica.

    • Aleja el ventilador del SSD hasta que pueda acceder fácilmente al conector del ventilador.

  3. Mac Mini Late 2014 reemplazo del ventilador: paso 3, imagen 1 de 2 Mac Mini Late 2014 reemplazo del ventilador: paso 3, imagen 2 de 2
    • Usa la punta de un spudger para levantar el conector del ventilador y sacarlo de su zócalo en la placa lógica.

    When I did this the entire socket came off the logic board. What do I do now?

    Tyler - Contestar

    I broke off the connector. More photos of the connector may help. I lifted it but the pins broke off. It took me awhile to find points on the board to solder the wires to. I got 3 of 4 wires and the fan operates.

    Beryl Sachs - Contestar

    I would suggest NOT using the point end of the Spudger but the wide end. Place behind connector (wire side) and twist gently.

    If I may be so bold as to also suggest that a torch be used for those small components/connections.

    TisMise - Contestar

    Thank you, @TisMise! I placed the wide end of the spudger on the wire end of the connector and wiggled it up. The connector comes lose up - NOT out front in direction of the wires. Hope this helps. ?

    CK3 -

    I also broke the socket off. I don’t have the ability to solder little $@$* like that. I’m sad.

    Daniel Rackerby - Contestar

    broke it… how bad is the no fan option?

    Kris Chu - Contestar

    @TisMise you’re right thanks a lot! ;)

    Stefania Izzo - Contestar

    You don’t need to disconnect the fan cable to take out the logic board. When you slip the logic board out, put the the fan behind the logic board as you push it out.

    Kenneth Z - Contestar

    Definitely use wide end.

    Peter Harrison - Contestar

    That’s it, I used a needle! After reading so much people broke it, I rejected this step instruction and put a needle between the socket and the connector. It came out fine. Good that I also fix clothes, other than computers. :)

    Seff - Contestar

    As Kenneth Z said, I just left the fan attached to the board for the entire process (I removed the screws so it was just connected with the cable). After reading all the comments, I was too afraid to try to force it and it did not come off easily. Keeping the connector on is a little dangerous because you have to be careful not to pull on that connector too much but it seems pretty robust, which is probably why it is so difficult to removed. I just slipped the fan through after I pulled out the main board assembly.

    Richard Daley - Contestar

  4. Mac Mini Late 2014 reemplazo del ventilador: paso 4, imagen 1 de 1
    • Quita el ventilador del Mac mini.

Conclusión

Para volver a ensamblar tu dispositivo, sigue estas instrucciones en orden inverso.

Un agradecimiento especial a estos traductores:

en es

87%

Estos traductores nos están ayudando a reparar el mundo! ¿Quieres contribuir?
Empezar a traducir ›

Sam Goldheart

Miembro Desde 10/18/12

465,252 Reputación

538 Guías creadas

Equipo

iFixit Miembro de iFixit

Staff

136 Miembros

16,573 Guías creadas

0 comentarios

Agregar Comentario

Ver Estadísticas:

Ultimas 24 horas: 0

Ultimos 7 días: 0

Ultimos 30 días: 0

Todo El Tiempo: 240